Fire Alarm Systems

Product Catalogue 2008 / 2009 

Fire Alarm Systems

Content General Details 1 - 6 

1 

2 

3 

4 

5 

6 

Introduction 3 

Extensions 4 

General Information 5 

Control Panels 7 - 58 

Conventional Control Panels 8 - 9 

IQ8Control 10 - 25 

System 8000 26 - 44 

Extinguishing system 45 - 53 

CMSI - French Standard 54 - 58 

Power Supply / Display and Operating Units 59 - 72 

Power Supply Units 60 - 61 

Voltage Converters 62 

Batteries 63 - 64 

Standard 65 

Serial Connection 66 

Network 67 

Fire brigade indicating + operating panels 68 - 72 

Network Technology 73 - 84 

essernet 74 - 77 

Multiprotocol Gateway 78 - 82 

IGIS-LOOP 83 - 84 

Management systems 85 - 99 

WINMAGplus 86 - 97 

WINMAGLite 98 - 99 

Automatic Detectors 101 - 136 

Detector Series 9000 Conventional 102 - 103 

Series IQ8Quad (Intelligent addressable) 104 - 115 

Detectors for Hazardous Areas 116 - 119 

Detector Base Series 9x00 120 

Base Series IQ8Quad 121 

Accessories 122 - 136 

1 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

2 

www.esser-systems.com 

7 

8 

9 

10 

11 

12 

13 

14 

Manual Call Points 137 - 156 

Large Design - ABS 138 - 141 

Large Design - Aluminium 142 - 143 

Large Design - Accessories 144 - 147 

Small design - ABS 148 - 153 

Special Design 154 - 156 

Transponders 157 - 170 

esserbus 158 - 170 

Wireless component 171 - 178 

Wireless modules 172 - 178 

Detectors for Special Applications 179 - 228 

Flame Detectors 180 - 183 

Air duct detector f. IQ8Quad Detector 184 - 190 

Line Heat Detectors 191 - 192 

Line Smoke Detectors 193 - 199 

Aspirating Smoke Detectors 200 - 227 

Accessories 228 

Alarm Devices 229 - 246 

IQ8Alarm 230 - 236 

Conventional 237 - 243 

Remote Indicators 244 - 246 

Door release system 247 - 257 

Automatic Door Systems 248 

Triggering Devices 251 - 252 

Door Holding Magnets 253 - 257 

Installation & Service 259 - 267 

Housings 260 - 266 

Services 267 

Appendix 268 - 288 

Planing guide for loop installation 270 - 271 

Order Form WINMAGplus / WINMAG Lite 272 - 273 

Order Form IQ8Quad for individual composition of languages 274 - 277 

Part Number Index 278 - 280 

Index 281 - 288

Introduction Dear business partners, 

You are looking at your personal issue of our 2009 product catalogue. We would be 

happy if you could take the time to assure yourself of our comprehensive product 

range. Your satisfaction has been our top priority ever since our company was founded 

35 years ago. Because of this, all changes and innovations made meet our basic principle 

to only offer products of maximum quality at a good price-performance ratio to 

you. You should pay special attention to the following products: 

• Our new UniVario Flame Detectors. 

• The conventional DIBt-approved IQ8 detectors with corresponding accessories. 

• One new upright cabinet, 600 mm model. 

• The Fire Protection Housing F30 RO for our fire alarm control 

panels with functional integrity of F30. 

• The new technical alarm module IQ8TAL. 

• The new multi-function test device for fire detectors. 

The high level of customer satisfaction which we have maintained for years now is 

represented by renowned references from all over the world such as: 

Steiff-Gruppe, Giengen / Germany • Albertina, Vienna / Austria • Kunsthalle Weishaupt, Ulm / Germany 

The success of these extraordinary projects is tied closely to your success. We would 

therefore like to further extend our cooperation together with you under the motto 

"Safety is a matter of partnership". Use this possibility of talking to us and tell us your 

suggestions and wishes so we can build the future together in this more and more difficult 

market environment. 

We are looking forward to continued success in working together, 

Your Esser Team 

3 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

4 

Extensions 

The list below provides a brief explanation of various extensions used in this product guide. 

acc. = according to 

approx. = approximately 

ARS = aspirating detector 

CCTV = closed circuit TV 

CPU = central processing unit 

CTC = center to center 

DB = database 

DFD = series 9100 

DIBT = German Institut for 

Technical Approvals 

DIL = dual in line 

DIN0 = German Institut for 

Standardization 

DIP = dual in parallel 

DKC = display keyboard card 

DRS = digital receiving station 

DU = Depth Unit 

EDD = series 9000 

EDP = Esser Data Protocol 

EL = Line voltage 

EN = European Norm 

EOL resistor = end-of-line resistor 

Ex = explosion proof 

FACP = fire alarm control panel 

FAS = fire alarm system 

FBF = firepanel for Fire Brigade 

FD = fire detection 

FDC = fire detection panel 

FDOP = fire brigade panel 

FDS = fire detection system 

FSA = door release system 

HU = used for 19 inch rack e.g. "6HU" 

1 HU = 44.45mm 

I/O = input/ output 

IC = integrated circuit 

IDS = intruder detection system 

IDT = intelligent display terminal 

IP = ingress protection rating 

IR = infrared 

LAN = local area network 

LCD = liquid cristal display 

LED = light emitting diode 

LF = low frequency 

LPCB = Loss Prevention Certification 

Board 

LRS = high sensitivity aspiration 


detector 

MCP = manual call point 

MFAB = master box 

MM = micromodule 

NC = normally closed contact 

NO = normally open contact 

OMF = operating module front 

PAM = series 9200 

pcb = printed circuit board 

pcs. = pieces 

PLC = programmable logic control 

PM = delay and verify functions 

POROM = programmable read only 

memory 

PTB = National Institute of Natural 

and Engineering Sciences 

RAM = random access memory 

RIP = remote indicating panel 

ROR = rate-of-rise heat detector 

SHV = smoke heat ventilation 

module 

SMD = surface mounted 

technology 

SOC = switch-on control 

SZI = single zone indicator 

TAL = technical alarm module 

TM = coincidence detection 

USB = universal serial bus 

UV = ultra-violet 

VDE = Association for Electrical, 

Electronic and Information 

Technologies 

VdS = Association of German 

Property Insurance 

Companies 

VGA = video graphics array 

VPP = voltage peak-peak

Abbreviations 

= List of contents which the part number includes 

= Information, important notice 

such as special versions, dependencies etc. 

= Packing unit 

Notice regarding the packing unit: 

1. The item will only be sold in packing unit. 

2. The number of items, which have to be ordered, always refers to the number of packing unit rather than the 

number of single items. 

3. The price stated in the catalogue is always the respective price for the packing unit. It is not the price for the 

single item. 

Example item number 701040 (spare glass pane): 

Packing unit: 10 items. An order of 3 items, for instance, would be equivalent to an order of 3 packing units. 

This would correspond to 30 items of spare glass pane, which have been ordered. 

What happens, if the phase-out date of a product is reached? 

1. We guarantee to supply you for up to five years all related components are available and the legal regulations permit this. 

2. Manufacturing-stop date is five years after the phase-out date. No matter whether we are able to manufacture the items, we 

will stop manufacturing them. 

3. After stopping delivery, as far as it is possible for us, we will try to repair the product for further two years. 

4. So long as stock is available, the products can be ordered further with the same part number, as far as this is legally permissible. 

5. As soon as the products are no longer available in our main-warehouse, we supply you with products of our service and repair 

warehouse. These products are marked by a "K"-Number. In this case it can be a repaired product, however as good as new. 

Also here we must consider the actual legal regulations. 

Ingress Protection rating 

Degrees of protection against solid foreign 

objects indicated by the first characteristic 

numeral 

First characteristic brief numeral description: 

0 Non-protected 

1 Protected against solid foreign 

objects of 50 mm diameter and greater 


objects of 12,5 mm diameter and greater 





5 Dust-protected 

6 Dust-tight 

Degrees of protection against liquid foreign objects 

indicated by the second characteristic numeral 

Second characteristic brief numeral discription: 

0 Non-protected 

1 Protected against vertically falling water 

drops 

2 Protected against vertically falling water 

drops when enclosure tilted up to 15° 

3 Protected against spraying water 

4 Protected against splashing water 

5 Protected against water jets 

6 Protected against powerful water jets 

7 Protected against the effects of temporary 

immersion in water 

8 Protected against the effects of continuous 

immersion in water 

5 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

6 

www.esser-systems.com

Control Panels Conventional Control Panels 8 - 9 

IQ8Control 10 - 25 

System 8000 26 - 44 

Extinguishing system 45 - 53 

CMSI - French Standard 54 - 58 

7 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

8 

Control Panels Conventional Control Panels 

Fire / Intruder Alarm Panel 2001 

382011 

382001 

382201 

382010 


¬G5,+− 

¬G5"t− 

¬G7"x− 

¬G5+(− 

Fire / Intruder Alarm Panel 2001 - english language 

Universal small control panel containing two detector groups for monitoring intrusion 

and/or fire detectors. It allows contacts and motion or glass break detectors to be connected. 

Alternatively, up to 30 fire detectors of the 9000 / 76xxxx series or up to 10 fire 

detectors equipped with switch-on control of the 9000 / 78xxxx series and 10 detectors of 

the 9100 series can be connected per detector group without addressing using the standard 

base 781590. 

An additional permanently armed, resistance-monitored input monitors technical alarms, 

tamper or hold-up detectors or manual fire alarms. Remote arming is possible, e. g. via a 

key-operated switch. A control input allows alarms to be acknowledged, cleared and/or the 

control panel to be armed/disarmed. 

Technical Data 

Rated connection voltage 230 V AC 

Nominal frequency 50 to 60 Hz 

Rated current 0.1 A 

Rated operating voltage 12 V DC 

Quiescent current approx. 40 mA 

Current consumption for ext. devices max. 350 mA 

Battery capacity 12 V / 2 Ah 

Relays 2 

Contact load relay 30 V DC / 1A 

Transistor outputs 4 (12 V DC / 0.5 A) 

Operating temperature range -5°C to +45°C 

Storage temperature range -5°C to +50°C 

Environmental class according to VdS II 

Type of protection IP 40 

Housing ABS plastic 

Colour white, similar to RAL 9016 

Colour of front plate grey-blue, similar to RAL 5008 

Dimensions (W x H x D) 270 x 221 x 71 mm 

Class of protection I according to DIN EN 60950 

Weight 1.5 kg 

Fire / Intruder Alarm Panel 2001 - Esser, German 

as 382011, but with front plate: German labelling 

Fire / Intruder alarm panel 2001 - Esser, Dutch 

as 382001, but with front panel: Dutch labelling 

Fire / Intruder Alarm Panel 2001 - Esser, Russian 

as 382001, but with front panel: Russian labelling

Control Panels Conventional Control Panels 

FACP 80 

Features 

• 4 or 8 detector zones with up to 30 detectors per 

detector zone 

• LCD display with two lines with 20 characters for 

each line 

• Single zone indication 

• CPU failure safe operation 

• 1 common fire output, potential-free, max. 30V 

DC / 2A 

• 1 alarm device output, monitored, 24V / max. 

500mA operation 

• 1 interface for fire man routing equipment 

• 1 interface for routing fault events 

• “Transmission delay” function (PM operation to 

avoid deceptive alarms, delay / interrogation) 

• “Two-alarm dependency” function (TM operation 

to avoid deceptive alarms being triggered), alternative 

programming: intermediate alarm storage 

for each detector zone, two-detector dependency 

for each detector zone, two-zone dependency between 

detector zones 1&2, 3&4 

• Connection for fire brigade operating panel, in 

compliance with DIN 14661 

• 12V / 400mA voltage supply for fire brigade operating 

panel or other use 

• Integrated connection for fire brigade key box 

• 4 zone related transistor outputs, 12V or 24V 

(external), capacity of up to 50mA 

• 1 relay as changeover contact, freely programmable 

(fire, pre-alarm, trouble, disconnection), 

option between floating or 24V operation 

• 24V / 0.5A voltage supply for external devices 

• Alarm counter 

• Test mode 

• Potential-free transmission unit output for actuating 

dial-up devices (TWG) 

• Central output for alarm signalling devices if no 

fire brigade key box is connected 

• Switch function for automatic door holder system 

(without DIBT approval) 

788705 

788706 

788706.GB0 

¬ox&`− 

¬ox'c− 

¬ox'§/HC1$− 

Approval: 


VdS, CNMIS, CNBOP 

Microprocessor-controlled fire alarm control panel with 4 or 8 detector zones in compliance 

with DIN EN 54, DIN VDE 0833 and DIN 14675, for connection to automatic conventional 

detectors (76xxxx) and manual call points of Series 9000 without switch-on control. 

Rated voltage 230 V AC 


Operating voltage 24 V DC 


Quiescent current typ. 16 mA / max. 24.5 mA 

Battery capacity 2 x 12 V / 7 Ah 

Ambient temperature -5 °C to +45 °C 

Storage temperature -5 °C to +50 °C 

Class of protection I as per DIN EN 60950 



Colour grey, similar to Pantone 538 

Weight 3.1 kg 


Space for 2 x 12V/7Ah batteries (Part No. 018004) not included. End-of-line capacitor for zone 

monitoring (22 μF / 35 V), fitted in last detector of the zone required. 

Complete control panel including system software, installation material and installation / operating 

manual and log book for fire detection systems. Batteries are not included. 

Application example 

Accessories: 

804900 Conventional MCP electronic module 

804901 Conventional MCP electronic module with second microswitch 

804970 Conventional MCP, red housing with glass pane - Esser 

704477.10 MCP-electronic module Series 9000 with second micro-switch 

704480.10 MCP-electronic module with 24 V DC 

766239 Sounder, red 

766304 Flashing light, 24V DC, amber 

766306 Flashing light, 24V DC, red 

766308 Flashing light, 24V DC, green 

766410 Optical alarm signalling device - red 

766411 Optical alarm signalling device - amber 

766412 Optical alarm signalling device - green 

766413 Optical alarm signalling device - blue 

766414 Optical alarm signalling device - transparent 

761162 Fixed heat detector 

761262 Rate-of-rise heat detector 

761362 Optical smoke detector 

781590 Standard detector base series 9x00 

781804 Remote indicator, red, for detector series 9000 

781487 Adapter module for base 781590 

FACP 80-4 - Esser, German, 24 V DC 

With 4 detector zones 

FACP 80-8 - Esser, German, 24 V DC 

With 8 detectors zones 

FACP 80-8 - Esser, English, 24V DC 

as 788706, but english version 

9 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

10 

Control Panels IQ8Control 

IQ8Control C / Intelligent Addressable 

Features 

• Max. two micromodules 

• Max. two esserbus analog loop modules 

• Short circuit and open circuit resistant loop operation 

• Loop installation with I-Y(ST)Y 0.8mm cable for a 

maximum length of 3.5 km 

• Up to 127 fire detectors / detector zones per loop 

• Up to 32 esserbus transponders per loop / operation 

of wireless components (see chapter 10) 

• Operation types TM and PM as per DIN VDE 0833 

- 2 to avoid unwanted alarms being triggered 

• Fire brigade operating panel and alarm transmission 

unit interface on the peripheral module 

• Three common relays, freely programmable, 

monitored, floating for up to 24 V DC / 1A (on the 

peripheral module) 

• TTY or RS 485, RS 232 interface 

• Integration in the short circuit and open circuit 

resistant essernet network with up to 31 fire 

detection panels depends on transmission rate 

• Connection to graphical supervisor WINMAG via 

serial essernet interface (SEI) 

• Operating panel with alphanumerical display 

• Event memory for up to 10,000 events 

• All System 8000 micromodules are compatible 

• Printer interface for internal printer 

• Two batteries with monitoring circuit 

• Monitored input for external power supply unit 

Additional features for powered loop 

• Max. 2 analog powered loop modules 

• BUS powered, synchronously controlled, acoustic 

alarm signalling devices as per DIN EN 54-3 with 

alarm tone as per DIN 33404 

• Up to 48 powered loop base sounders (Series 

9200) per loop 

• Up to 32 powered loop IQ8Alarm per loop 

• Up to 48 IQ8Quad with alarm device per loop 


Approval: 

VdS, CNBOP, BOSEC 

The IQ8Control C as an efficient fire alarm control panel for the property supervision of 

small to mid-sized objects, facilitates simultaneous detection, control and alarm signalling 

both on the analogous ring as well as on the spur. 

Within the multifunctional IQ8Control C panel, the operation type (powered-loop or nonpowered-loop) 

can be selected via a jumper located on the control panel power supply unit. 

Depending on which loop operation type has been selected, the respective loop module / 

modules are need to be. 




Rated current 0,35 A (Standard); 0,7 A (esserbus-PLus) 

Quiescent current 215 mA (basic configuration without operating unit) 

230 mA (basic configuration with operating unit) 

295 mA (basic configuration with operating unit 

with 1/4 VGA display) 

Emergency power supply 2 x 12 Ah, 2 x 24 Ah in extension housing 

Operating current for external load max 2.0 A 

Ambient temperature -5°C to +45°C 

Storage temperature -5°C to +50°C 


Housing ABS, 10% glass fibre reinforced, V - 0 


Weight approx. 6.5 kg 


- The IQ8Control fire detection panels are fully compatible with FACP 8000 panels within 

essernet applications 

- FACP 8000 micromodules are also compatible with IQ8Control devices 

- Housing form and colour comply with the FACP 8000 generation 

- The IQ8Control panels can only be programmed with the tools 8000 software solution (Part 

No. 789861) and the field bus interface (Part No. 789862.10) or directly via USB with the 

RS-232 interface (Part No. 769828), with the field bus interface or the RS232 interface. 

Combined with 808619 or 808619.10 FSA transponders, the control panel can be used to control 

automatic door arrester systems in compliance with the German institute for construction 

engineering (DIBt: Deutsches Institut für Bautechnik). 

Connection example


IQ8Control C design and order diagram 

11 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

12 


Control Panels 

808003 

808139 


¬qq$N− 

¬qrHU− 

Fire alarm panel IQ8Control C 

Basic design. 

The operating front must be ordered separately. 

Housing with standard rear panel and front frame for operating panel fronts, interface board, 

power supply module, system software. 

Fire alarm panel IQ8Control C for 19” cabinet 

As 808003 but 19” version (7 HU) for upright cabinet installation. 


FACP 808003 IQ8Control C, including 19” installation frame and flat cable for 19” installation 

750707.


Accessories FACP IQ8Control C 

789300 

789301 

¬o~!]− 

¬o~"`− 

Battery extension housing 

Extension housing for additional batteries. 





Housing ABS plastic, 10% glass fibre reinforced, V - 0 


Weight approx. 5kg (without battery) 

Dimensions (W x H x D) 450 x 320 x 185mm 

Batteries are not included and must be ordered separately. 

Housing complete with battery rear panel, connecting cable for battery, mounting positions for 

2 x 12V/24Ah batteries. Neutral front and material for attaching to the existing panel housing, 

battery connecting cables, 800 mm. 

Connection between the central housing and the extension housing 

Extension housing for batteries and SZI 192 detector zones 


Quiescent current 5mA 

Current consumption 1.5mA when LED activated 



Weight approx. 5.5kg (without battery) 




This housing cannot be used if an operating module front with single zone indicator unit for 64 

zones is already fitted. Batteries are not included and must be ordered separately. 

A single zone indicator unit can only be used in connection with an operating module front. 

Housing complete with battery rear panel, connecting cable for batteries, mounting positions 

for 2 x 12V / 24Ah batteries, single zone indicator front for 192 detector zones and material for 

attaching to the existing panel housing. 

13 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

14 


789302 


¬o~#c− 

Extension housing for SZI 192 detector zones 

The housing can be used to mount additional modules, e.g. an esserbus transponder. 


Control Panel Packages IQ8Control C 

808020 

¬qq5£− 


Current consumption 1.5mA when LED activated 



Weight approx. 5kg 




This housing cannot be used if an operating module front with single zone indicator unit for 64 

zones is already fitted. A SZI unit can only be used in combination with an operating module 

front. 

Housing complete with standard rear panel, single zone indicator front for 192 detector zones 

and material for attaching to the existing panel housing. 

Package IQ8Control C with two slots for micromodules 


1 x control panel 808003 

1 x extension module 772478


IQ8Control M / Intelligent Addressable 

Features 

• Max. seven micromodules, with peripheral 

module 772418 max. five micromodules 

• Max. seven esserbus analog loops, with peripheral 

module 772477 max. five esserbus analog 

loops 

• Short circuit and open circuit tolerant loop operation 


maximum length of 3.5 km 

• Up to 127 bus devices / detector zones per loop 

• Up to 32 esserbus transponders per loop / operation 

of wireless components (see chapter 10) 

• Operation types TM and PM as per DIN VDE 0833 

- 2 to avoid unwanted alarms being triggered 

• Fire brigade operating panel and transmission 

interface on the peripheral module 

• Three common relays, freely programmable, 

monitored, floating for up to 24 V DC / 1A (on the 

peripheral module) 

• TTY or RS485 or RS 232 interface 

• Integration in the short circuit and open circuit 

resistant essernet network with up to 31 fire 

detection panels depends on transmission rate 

• Connection to graphical supervisor WINMAG via 

serial essernet interface (SEI) 

• Operating panel with alphanumerical display 


• All Systems 8000 micromodules are compatible 

• Printer interface for internal printer 

• Two batteries with monitoring circuit 

• Monitored input for external power supply unit 

Additional features for powered loop 

• Max. 4 analog powered loops and expandable up 

to 124 power loops 

• BUS supplied, synchronously controlled, acoustic 

alarm signalling devices as per DIN EN 54 - 3 with 

alarm tone as per DIN 33404 

• Up to 48 powered loop base sounders (Series 

9200) per loop 

• Up to 32 powered loop IQ8Alarm per loop 

• Up to 48 IQ8Quad with alarm device per loop 

Approval: 

The IQ8Control M as an efficient fire alarm control panel for the property supervision of midsized 

to large objects, facilitates simultaneous detection, control and alarm signalling both 

on the analogous ring as well as on on the spur. 

The loop operation type of the panel (powered-loop or non-powered-loop) can be selected 

via a jumper located on the power supply card. 

Depending on which loop operation type has been selected, the respective analog module / 

modules should be used. 


Output voltage 12 V DC 

Rated voltage 230 V 


Rated current 0,35 A (Standard); 0,7 A (esserbus-PLus) 

Maximum current drawing external user 2 A 

Quiescent current 300 mA without operating unit 

340 mA with operating unit 

420 mA with 1/4 operating unit without illumination 

580 mA with illumination 

Battery capacity 2 x 12 Ah, 24 Ah 






Weight 11.5 kg 


- The IQ8Control fire detection panels are fully compatible with FACP 8000 panels 

- FACP 8000 micromodules are also compatible with IQ8Control devices 

- Housing form and colour comply with the FACP 8000 generation 

- The IQ8Control generation can only be programmed with the tools 8000 software solution 

(Part No. 789861) and the field bus interface (Part No. 789862.10) or directly via USB with 

the RS-232 interface (Part No. 769828), with the field bus interface or RS232 interface. 

Combined with the 4 zone/2 relay-transponder 808619or 808619.10, the control panel can be 

used to control automatic door arrester systems in compliance with the German institute for 

building technology (DIBt: Deutsche Institut für Bautechnik). 


VdS, CNBOP, LPCB, BOSEC 

15 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

16 



IQ8Control M design and order diagram (basic design)


Control Panels 

808004 

808219 

¬qq%Q− 

¬qs4¤− 

FACP IQ8Control M 

Basic design. 

Control Panel Packages IQ8Control M 

808030 

808031 

¬qq?8− 

¬qq@;− 


Housing with rear panel and front frame for operating panel fronts, interface board, power 

supply module and system software. 

FACP IQ8Control M for 19” cabinet 

As 808004 but 19” version (7HU) for upright cabinet installation. 


FACP IQ8Control M 808004, including 19” mounting frame and flat cable for 19” installation 

750707. 

Package IQ8Control M with four slots for micromodules 



1 x extension module 772476 

Package IQ8Control M with seven slots for micromodules 



2 x extension modules 772476 

17 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

18 


808218 

789304 


¬qs3¡− 

¬o~%i− 

Package IQ8Control M black box 

With 4 micromodule slots without operating front. 

Space for up to 2 x 12V / 24Ah batteries (Part No. 018006). The essernet micromodule must be 

ordered separately. 


1 x neutral front 786100 

1 x extension module 772476 

1 x essernet micromodule: 62.5 kBd (Part No. 784840) or 500 kBd (Part No. 784841) option 

Extension housing for Package Part No. 808218 IQ8Control M 










The operating front must be ordered separately and is not included in the price. The extension 

housing must always be mounted on top of the double housing of the IQ8Control M (Part No. 

808218). For expanding the IQ8Control M fire alarm panel by an integrated printer with paper 

take-up reel, the extension housing (Part No. 789304) must be mounted above the fire alarm 

panel. 

1 x operating panel front 7863xx 

1 x printer 

1 x paper take-up reel


IQ8Control C/M 

IQ8Control C/M operating fronts 

786001 

786101 

¬o]"§− 

¬o^"©− 

Esser - front (786001, 786101, 786301, 786401, 786501, 786801 and 786901) is also available 

with the respective country specification - except the special versions. When ordering, please 

fill in the last two digits by the specific language code. 

Example: 

The German version of the standard operating front C/M would have the Part No. 7860-01. 

For the Dutch version, the number would have to be changed to 7860-08. 

For the Dutch variant please order 7860-08. 

Following language- / national variants are available: 

01 German 

02 English 

03 Italian 

04 Portuguese 

05 Polish 

06 Spanish 

07 Austrian 

08 Dutch 

09 Czech 

10 Russian 

11 Hungarian 

12 Danish 

13 Swedish 

14 Croat 

15 French 

16 Slovak 

18 Romanian 

20 Turkey 

21 Greece 

22 Flemish (Belgium - Dutch) 

23 Walloon (Belgium - French) 

25 Arabian / English 

Operating front - Esser, German 



Operating front w. single zone indication 64 - Esser, German 


Quiescent current 50 mA 

Current consumption single zone indication: per activated LED 1.5mA 

19 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

20 


786801 

786301 

786401 

786452 

786501 

786552 


¬oe".− 

¬o`"$− 

¬oa"&− 

¬oaUX− 

¬ob"(− 

¬obUZ− 

Operating front with printer, w/o take-up reel - Esser, German 



Operating front for printer w. take-up reel - Esser, German 



This operating module front can only be used on IQ8Control M. 

The printer kit with paper take-up reel (Part No. 784892) must be ordered separately. 

Operating front with 1/4 VGA display - Esser, German 

Two-line additional text can be programmed using the programming software package. 



Resolution 320 x 240 pixels 

Remote diagnosis is not possible if a two-line extra text is programmed. 

Operating front with 1/4 VGA display - Esser, Chinese 

Operating front w. 1/4 VGA display & SZI for 64 zones - Esser, German 




Current consumption single zone indication: per activated LED 1.5mA 



Operating front 1/4 VGA and SZI for 64 zones - Esser, Chinese


786901 

786952 

786000 

786100 

788093 

¬of"0− 

¬ofUb− 

¬o]!¤− 

¬o^!¦− 

¬oq~%− 

Operating front w. 1/4 VGA display, printer - Esser, German 




Current consumption printer: 45mA 



Operating module front with 1/4 VGA display + printer - Esser, Chinese 

SZI front for 192 detector zones 



Current consumption single zone indication: per actuated LED 1.5mA 

Including insertable foils with country-specific versions 

Filler panel front, neutral for IQ8Control C/M 

19” rack mounting kit for SZI 192 detector zones 

7 HU for upright cabinet mounting. 



Current consumption 1.5mA per actuated LED 

772445 mounting frame, 786000 SZI front for 192 detector zones, including insertable foils 

with country-specific versions 

21 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

22 


786261 

786262 

786263 


¬o_ô− 

¬o__r− 

¬o_ù− 

IQ8Control C/M operating unit front with FBOIU- Esser, German/Switzerland 

With integrated Swiss fire department operating and indicating unit (FBOIU) - German lettering 

IQ8Control C/M operating unit front w. FBOIU- Esser, Italian/Switzerland 

as 786261, but with Italian lettering 

IQ8Control C/M operating front w. FBOIU - Esser, French/Switzerland 

as 786261, but with French lettering


Control Panel Modules for IQ8Control C/M 

772479 

772477 

772478 

772476 

¬n9pX− 

¬n9nR− 

¬n9oU− 

¬n9mO− 

Peripheral module 

The peripheral module contains a fire brigade operating panel interface as well as a alarm 

transmission unit interface and three freely programmable, optionally monitored or up to 

24V DC floating common relays. The peripheral module can only be used on system terminal 

1 of the control panel interface board. 



Only one 772477/78/79 module can be plugged onto the interface board. 

Peripheral module with one additional micromodule slot 

As 772479 but with one additional micromodule slot. The peripheral module can only be 

used on system terminal 1 of the control panel interface board. 


Quiescent current 15mA (without micrmodule) 

Only one 772477/78/79 module can be plugged onto the basic module. 

Extension module with one additional micromodule slot 

The extension module is plugged onto the interface board of the control panel. The extension 

module can only be used on system terminal 1 of the control panel interface board. 


Quiescent current 5mA (without micromodule) 

Only one 772477/78/79 module can be plugged onto the interface board. 

Extension module with 3 additional micromodule slots 

The extension module is plugged onto the interface board of the control panel. This extension 

module can be used on plug connectors 1 and 2 of the basic control panel module. 


Current consumption 5mA (without micromodule) 

The 772476 extension module can only be used in the IQ8Control C/M fire alarm panel. 

23 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

24 


Accessories for IQ8Control C/M 

784892 

736235 

789303 

Features 


¬oQ}I− 

¬j_D¥− 

¬o~$f− 

• For the installation of up to 10 transponders 

and FO Converters with Installation Kit 788605. 

772445 

¬n9NY− 

Printer kit with paper take-up reel for IQ8Control C/M 

40 characters, printer with fixed print head. 

When the printer is installed in the FACP IQ8Control C, the battery case, including toroidal 

transformer, must be replaced by the mounting rack. The batteries and the toroidal transformer 

must be installed in an additional extension housing, either 789300 or 789301. 

Mounting frame complete with part no. 736234 plain text thermal printer including winder and 

end-of-paper recognition. 

Accessories: 

736235 Printer paper for printer 736233 / 736234 

Printer paper for printer 736233 / 736234 

Printer paper for Part No. 736233 printer without paper take-up reel and for Part No. 736234 

printer with take-up reel. 


Dimensions (L x W) 25 x 58 mm 

Extension housing 

The standard extension housing can be used to mount additional modules, e.g. esserbus 

transponders. 







Weight approx. 5 kg 


Housing complete with standard rear panel, neutral front and material for attaching to the existing 

control panel housing. 

Mounting frame 19” IQ8Control C/M and FACP 8000 C/M


789310 

Features 

• Allows termination of fire cables 

• Ten cable entry points 

• Wall adjust elements for panel installation on 

uneven surface 

• Simple installation 

¬o~+{− 

Intermediate distribution frame for IQ8Control C 

The Mounting box assembly (Part No. 789310) is a first fix component for the installation 

of the 8000 C/M or IQ8Control C/M fire alarm control panel and is specially designed to 

allow termination of fire cables. 


Cable entry 10 

Ambient temperature -10 °C to +40°C 


Weight 1,1 kg 

Colour similar to Pantone 538, grey 



Mountin example 

25 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

26 

Control Panels System 8000 

FACP 8008 / Intelligent Adressable 

Features 

• Fully redundant with second CPU (option) 

• Short circuit and open circuit resistant esserbus 

loop operation 


maximum length of 3.5km 

• Up to 127 fire detectors/detector zones per loop 

• Up to 32 esserbus transponders per loop 

• Delay, verification time, to enable manual intervene 

• Fire brigade operating panel interface integrated 

• Master box interface on master box micromodule 

• TTY or RS 232 interface - optional 

• Up to 30 panels can be networked via the short 

circuit and open circuit resistant essernet 

• Connection to supervisor e.g. Winmag 

• Computer-aided remote diagnosis 

• Operating module with alphanumeric display 

• Event memory for up to 200 events 

• All System 8000 micromodules are compatible 

• Interface for log printer 

• Connectors for two storage batteries with monitoring 

circuit 


Approval: 

VdS, CNBOP 

Microprocessor-controlled fire alarm panel in accordance with DIN EN 54, VDE 0833 and 

VdS, for connecting automatic detectors and manual call points as well as the various 

esserbus transponders. The following fire detectors can be connected: Series 9000 / 9200 

/ IQ8Quad. 




Output current 12 V DC 

Quiescent current 400 mA, for basic design 

Rated current 2.9 to 1.1 A 

Battery capacity up to 2 x 12 V DC / 40 Ah 

Ambient temperature -5° to +45°C 

Storage temperature -5° to +50°C 


Housing sheet steel 

Colour grey, similar to RAL 7035, blue, similar RAL 5003 

Plain text display illuminated with 8 x 40 characters 

• Monitoring input for external power supply Our Technical Marketing Consultants will gladly assist you in the project planning of larger central 

control unit extensions concerning the details of technical and application-oriented applications. 

Application example


Design and order diagram 

27 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

28 


Panels FACP 8008 

768308 

768318 

768398 


¬mt)_− 

¬mt3}− 

¬mt¥8− 

Fire alarm panel 8008 in S1 housing - Esser 

Basic version. 


Weight ca. 26 kg 


Wall housing with basic chassis and cover housing. Basic housing with space for one power 

supply unit and six 19” IO-card slots. 

Operating module 7684xx, filler panel module left 772360 and power supply 784026 must be 

ordered seperately. 

772330 wall housing 

included: 

771456 A/B control card 

771451 backplane bus 

771796 I/O card 

771450 I/O terminal card 

771794 CPU card 

771671 power supply terminal card 

771788 EEPROM card 

772365 filler panel module, right 

Accessories: 

772366 Filler panel module left 

784026 Power supply unit for fire alarm panel 8008 

770392 Systemsoftware Master 

Fire alarm panel 8008 in S1-E housing - Esser 

As 768308 but with more space for batteries. Required for installation of hinged printer 

frame 2 batteries. 




Operating module 7684xx, filler panel modules left 772360 and power supply 784026 must be 

ordered separetely. 

Accessories: 



770392 Systemsoftware Master 

Fire alarm panel 8008 for 19” cabinet - Esser 

As 768308 but 19” version (6 UH); for upright cabinet mounting. 

Operating module 7684 -20 to 37 is included in price, must be ordered separetely. 

Accessories: 



770392 Systemsoftware Master


Software - FACP 8008 

770392 

770393 

¬n$}U− 

¬n$~X− 

Operating modules - FACP 8008 

768420 

768411 

¬mu5§− 

¬mu,j− 

Master system software for FACP 8008 

Required for operating FACP 8008. 

Slave system software for FACP 8008 

Required for operating a second CPU in FACP 8008. 

Required when the fire detection panel is used in redundant operation mode. 

Operating module front - Esser, German 

Each operating front is also available with the respective country specification. When ordering, 

please fill in the last two digits by the specific language code. 

Example: 

The German version of the standard operating front 8008 would have the Part No. 768420. 

For the Dutch version, the number would have to be changed to 768429. 

Following language/country variants are available: 

20 Germany 

21 England 

22 Italy 

23 Portugal 

24 Austria 

25 Poland 

26 Spain 

29 Netherlands 

31 Czech Republic 

32 Russia 

33 Hungary 

34 France / Switzerland 

35 Slovakia 

36 Croatia 

37 France 

Operating module front with ¼ VGA display - Esser, English 

Each operating front is also available with the respective country specification. When ordering, 

please fill in the last two digits by the specific language code. 

Example: 

The German version of the standard operating front 8008 would have the Part No. 768414. 

For the English version, the number has to be changed to 768411. 

The following versions are available: 

Language codes: 

11 English 

13 Chinese 

16 Russian 

29 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

30 


Control Panel Modules - FACP 8008 

771794 

784760 

771669 


¬n2¡w− 

¬oP]N− 

¬n1f*− 

CPU card for FACP 8008 

Panel control unit for installation in 8008 fire alarm panel. 

A second I/O card (784760) and the 770393 slave software package are required for a redundant 

CPU card. 

Input/output (I/O)-card for micromodules - Esser 

I/O card for the control of micromodules and the modular extension of the panel. Including 

BUS communication and data exchange with the central processing unit. Up to 8 micromodules 

can be mounted on each I/O card. 

Including 771450 I/O terminal card 

Accessories for Fire Alarm Panel 8008 

784026 

¬oI;A− 

Power supply unit for FACP 8008 

Primarily pulsed supply unit for supplying power to FACP 8008 and recharging batteries in 

parallel mode. 


Rated voltage 115 V DC / 230 V AC / 50 HZ 


Output voltage 12 V DC / 24 V DC 

Output current 4 A @ 12 V DC; 1 A @ 24 V DC 

Battery capacity max. 2 x 40 Ah 

Terminal card power supply, series 3


764701 

784141 

772333 

772331 

¬mP"i− 

¬oJJp− 

¬n8B3− 

¬n8@-− 

Kit for limitation of capacity limit for FACP 8008 

The capacity limiter-kit is mounted inside the housing of the Fire Alarm Control Panel 8008 

and provides the interference voltage decoupling of the connected analog loops. This device 

is suited to prevent the fault message >Com. trouble ground fault< caused by the cable 

shielding of the analog loop, in any applications where adversed installations must be considered. 

The cable shield can be connected via an external terminal to each of the 10 gray connection 

leads of the kit from up to four analog loops. 

Up to 4 cable shieldings of different analog loops may be connected via an external terminal 

(supplied) to one of the 10 grey connection cables. Thus a total of all analog loop cable 

shieldings may be connected to this Kit per FACP 8008. 

Single zone indicator card for max. of 64 zones 

Single zone indicator unit for up to 64 detector zones, status display of “Disconnection, 

Fault, Fire and Initial (SZI) Alarm - Fire”. 

Extension chassis S1-E for FACP 8008 

Extension kit consisting of rear panel sheet and cross arm for S1-E extension. 

including mounting material 

Extension housing kit S1-E for FACP 8008 

Extension kit consisting of S1-E housing, lock and cover plates. 

31 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

32 


750707 

772147 

784885 

736235 

736264 


¬l((*− 

¬n6PY− 

¬oQv4− 

¬j_D¥− 

¬j_as− 

Flat cable 40-pin for 19” rack mounting 

Connection between 8008 operating module control card and operating module. 


Length 120cm 

19” mounting kit for FACP 8008, operating unit front 

For mounting operating front, 6 HU. 

1 x frame 741755 

2 x mounting brackets 741763 

1 x 1.2m bus cable 750707 

Mounting material 

19” mounting kit for retrofitting 

For mounting 6 HU, 784883 printer (printer isn’t included). 

1 x frame 741755 

2 x mounting brackets 741763 

1 x printer connection cable 750755 

1 x PVC insulating sleeving 752414 

Mounting material 

Printer paper for printer 736233 / 736234 

Printer paper for Part No. 736233 printer without paper take-up reel and for Part No. 736234 

printer with take-up reel. 



Printer paper for printer 736259 

For printers (Part No. 736259) with paper take-up reel. 


Dimensions (L x W) 25 x 60 mm


772365 

772366 

772363 

784883 

¬n8b,− 

¬n8c/− 

¬n8`&− 

¬oQt.− 

Filler panel module right 

Filler panel module left 

Single zone indication module with bus board 

Module for up to 3 single zone indicator cards. 

1 modul per panel is required 

Including insertable foils with country-specific versions 

Printer for mounting in wall housing - Esser 

Hinged frame complete with plain text thermoprinter and paper take-up reel, delivered with 

interface. 

If the hinged frame is mounted in the 763808 type housing there is room for only 1 battery of 

up to 40 Ah. Printer with fixed print head and “paper end” signal, prints 40 characters per line. 

Accessories: 

736235 printer paper for printers 736233 / 736234 

33 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

34 


Packages Fire Alarm Panel 8008 

768428 

768418 

768448 


¬mu=6− 

¬mu3¡− 

¬muQr− 

The operating modules are not included in the panel/package price and must be ordered separately. 

Package 1 of FACP 8008 


Space for max. 2 x 12V DC/38Ah batteries (Part No. 018008). 

1 x 8008 fire alarm panel 

1 x 784026 power supply unit 

1 x 771671 power supply + terminal card 

1 x 7684xx operating module 

1 x 771456 A/B control card 

1 x 784760 I/O card + terminal card 

1 x 771788 EEPROM card 

1 x 771794 CPU card 

1 x 772365 filler panel module right 

2 x 772366 filler panel modules left 

1 x 770392 software master 

Package 2 of FACP 8008 with SZI 









1 x 772363 SZI basic module 

1 x 784141 SZI 64 zones 




1 x 772366 filler panel module left 


Package 3 of FACP 8008 with printer 


Space for max. 1 x 12V DC/38Ah battery (Part No. 018008). 







1 x 784883 printer 




1 x 772366 filler panel module left 

1 x 770392 software master


768408 

768408.VC0 

768438 

¬mu)a− 

¬mu)§/WD1¥− 

¬muGT− 

Package 4 of FACP 8008 with SZI and printer 


Space for max. 1 x 12V DC/38Ah battery (Part No. 018008). 









1 x 784141 SZI 64 zones 





Package of FACP 8008 - Esser, Chinese 

As 768408, but Chinese version 

Package of FACP 8008 with SZI and printer 




1 x 772331 S1-E extension housing 








1 x 784141 SZI 64 zones 





Micromodules for IQ8Control C/M and FACP 8008 Fire Alarm Panels 

784381 

¬oLr§− 

4-zones fire detection module 

Zone card for connecting up to 30 Series 9000 automatic fire detectors and / or up to 10 

Series 9000 manual call points per zone. 


Quiescent current approx. 25mA 

35 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

36 


784382.D0 

804382.D0 

784385 

784842 

787530 


¬oLs§/E1n− 

¬qLs§/E1p− 

¬oLv*− 

¬oQK£− 

¬ol?,− 

Analog loop module 

Single loop circuit module for up to 127 Series 9200 / IQ8Quad intelligent fire detectors or 

bus devices, divisible into 127 zones. 


Quiescent current ca. 25 mA 

Length loop: 3.5 km 

Analog loop module powered loop 

Single loop circuit module for up to 127 bus devices. Series 9200 / IQ8Quad intelligent fire 

detectors and esserbus transponders (Part No. 80xxxx) or addressable sounders and 

powered loop base sounders. 



Length loop: up to 3.5 km 

Powered loop compatible only with IQ8Control. 

Master box interface module 

Single master box interface module for activating and processing acknowledgement signals 

from master boxes; programmable as constant or pulsed master box activation. 



RS 232/TTY serial interface module 

Serial interface module with optional RS 232 or TTY typ, for operating external devices such 

as external printers, printers, modems for remote diagnosis. 


Quiescent current approx. 35 mA - RS 232 

approx. 55 mA - TTY 

4-relay module 

4-relay module with freely programmable output functions, each of which can operate as an 

NC or NO contact (not monitored) for potential-free activation. 



Contact load max. 30V DC / 1A per output 

Switching capacity per module max. 1A


787531 

787532 

787533 

¬ol@/− 

¬olA2− 

¬olB5− 

3-relay module 

3-relay module with output functions which can be programmed either as NC or NO contacts, 

3 x latching “monitored” relay outputs. 




Switching capacity per module max. 1A 

3-relay common fault module 

3-relay module with pre-set functions such as common fault, 2 x freely programmable 

monitored relay outputs. 




Switching capacity per module max. 1A 

Standard interface module for System 8000 and IQ8Control C/M 

The standard interface module enables extinguishing control equipment to be connected to 

System 8000 control panels. The module is provided with an additional monitored relay, 

which can be programmed for any function. With this module, acknowledge messages from 

the extinguishing system cannot be interpreted. 



Use in connection with 4/2 transponder for the processing of feedback, conforms with VdS 

37 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

38 


Accessories for System 8000 and IQ8 

788730 

Features 

• Max. 7 FACP 3007 & 3008 UZ connectable, in 

each case via a serial interface 784842 (not 

included, must be ordered separately) 

• Common trouble relay 

769163 

769164 

772084 


¬ox?D− 

¬m|`F− 

¬m|aI− 

¬n5u_− 

Gateway for FACP 3007/3008/3010 @ System 8000, IQ8Control 

The gateway is designed as a protocol converter for 3007 and 3008 fire alarm panels to 

System 8000 fire alarm panels and the IQ8Control series via the essernet. A maximum of 

seven 300x sub alarm panels and the essernet module can be connected to the gateway. 

Customer data for the gateway is programmed via the tools 8000 software solution. 





Current consumption for ext. devices max. 2 A 

Battery capacity max. 2 x 12 V DC / 24 Ah 

Rated current 0,7 A 

Ambient temperature - 5°C to +45°C 

Storage temperature - 10°C to +45°C 



Colour grey, similar to RAL 7035 



One slot is required for the essernet module 784840 or 784841 (not supplied as standard and 

must be ordered separately). 

Basic PCB, power supply unit, 2 micromodule extension cards, system software, wall cabinet 

with basic chassis 

Upright cabinet 

With full view glass and swiveling lever lock (PHZ) for housing of the System 8000 and 

IQ8Control as 19“ rackmount. Cabinet rack with welded 100 mm base, with drill holes for 

floor installation. 

Removable rear and side walls, cable inlet in top with bristles and cover plate. 40 HE hinged 

frame for integration of operating unit and facing with dummy plates. 


Material approx. 150 kg 

Dimensions (W x H x D) 800 x 2.000 x 600 mm 

Upright cabinet not suitable for the releasing control equipment 788014, 788015,788024, 

788025. 

Upright cabinet including mounting 

As 769163 but completely premounted at the factory for integrating a fire alarm control 

panel. 

Door contact for upright cabinet 

Only when combined with upright cabinet 769163.


743212 

743245 

769914 

743248 

769915 

¬kA-j− 

¬kANf− 

¬m¦/*− 

¬kAQo− 

¬m¦0-− 

Spare key 1D9 for FACP 

For upright cabinets 769163 and 769164. 

Lever lock - type 17 for key no. 801 

Spare key 801 for FACP 

For fire alarm panels 2001, IQ8Control C/M, 8000 M/C, 8007, 8008, for operating panel, 

printer and housing. 

Two keys. 

Lever lock - type for key no. 901 

Two keys and one cylinder lock. 

Spare key 901 for FACP 

For fire alarm panels 2001, IQ8Control C/M, 8000 C/M, 8008 for operating panel, printer and 

housing. 

Two keys. 

39 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

40 


744030 

744027 

744028 

744029 


¬kI?I− 

¬kIF− 

Dummy cover 19”, 2 HU 

For covering free installation space in upright cabinets and wall cabinets, 2 HU. 


Material sheet steel 


One height unit (HU) covers 44.45mm. 


As 744030, but 3 HU. 


As 744030, but 5 HU. 


As 744030, but 9 HU.


Maintenance and Test Equipment - System 8000 

789861 

789860.10 

¬o¥^P− 

¬o¥]§/21(− 

tools 8000 programming software 

Convenient Windows programming software CD for programming the fire alarm panels 

belonging to Series 8000 C/M, 8008, IQ8Control, Gateway, extended supplementary text in 

¼ VGA display and ABIGA. 

For programming, the 789862.10 field bus interface is required. 

System requirements: 

- FACP 8000 C/M, FACP 8008 or IQ8Control C/M as of software version V2.20 

- PC / Notebook as of Windows 98 SE, but no Windows NT (no USB support) 

- Recommended configuration: 128 MB RAM, 500 MHz CPU 

This software is also to be used for the LCD panels 785101 and 785103. 

tools 8000 PLus equipment starter kit 

Complete package for programming of the fire alarm control panels 8007, 8000C/M, 8008, 

gateway, ABIGA and IQControl via PC or Notebook. 

The field bus interface is used as a programming interface between the FACP and the PC/notebook. 

Furthermore the field bus interface facilitates the direct connection of a ring bus to the convenient 

monitoring of a finished installation and the elimination of possible cabling mistakes. 

789861 Programming software for system 8000 and IQ8Control 

789862.10 Field bus and control panel interface 789862.10 for tools 8000 

789863 USB cable 

789864 Serial Connecting Cable 

Accessories: 

BME2Z002 Switched-mode power supply with cylindrical plug 


41 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

42 


789862.10 

789863 


¬o¥_§/21.− 

¬o¥`V− 

Field bus interface PLus 

Interface for the programming of the fire alarm control panels 8007, 8000C/M, 8008, 

gateway, ABIGA and IQ8Control or for the direct field-side connection of a single installed 

analog loop. With the optional switched-mode power supply BME2Z002, bus-supplied 

alarm signaling equipment can be tested independently from the control panel via the direct 

connection to the field bus interface 789862.10. (V1.12 or above of programming software 

tools 8000 is required) 


Voltage supply via plug-in power supply (part no. BME2Z002) 

and/or via the USB connection 

Ambient temperature +5°C to +45°C 

Storage temperature 0°C to +50°C 


Housing plastic, PS (Polystyrene) 

Colour white, similar to RAL 9010 / 

grey, similar to RAL 7035 

Weight approx. 300 g g 


Connecting cables 789863 and 789864 are not included in delivery. 

Windows NT does not support any USB interface. Therefore the use of the programming software 

tools 8000 is possible under Windows NT only with the usage of programming interface 

RS 232 (Part No. 769828). 

One interface and two 6-pin plugs. 

Accessories: 

BME2Z002 Switched-mode power supply with cylindrical plug 


USB cable A/B for 789862 field bus & panel interface 

For connecting service PC / laptop with the tools 8000 field bus and panel interface. 


Cable length 1.8m


789864 

BME2Z002 

769828 

¬o¥aY− 

«CNF3[1138− 

¬m¥=R− 

Serial connecting cable for 789862 

For connecting the field bus interface to panels 8007, 8000C/M, 8008, Gateway, ABIGA and 

IQ8Control. With 4-pin special plug for the control panel. 


Length approx. 1.9m 

Switched-mode power supply with cylindrical plug 



Output current 1 A 

Control panel interface RS 232 

Interface for programming all Series 8000 fire alarm control panels, extinguishing panel 

8010 and 5008 intrusion detection control panels with a notebook and programming software. 

- IDT 770597 programming software and 381137 maintenance software 

- FDT tools 8000 programming software (789861) 

- 775814 Programming software for extinguishing panel 8010 / series 3 


Cable 1.5m with 4-pole special plug 


9-pin PC serial interface required! 

Interface cable 756649 

43 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

44 


ECS 8000M - French Standard 

Panel 

788297 

Features 

• compatible with FACP 8000 M 

788298 


¬os¤5− 

¬os¥8− 

Fire alarm panel ECS 8000 M - Esser, French 

Approval: 


CNMIS 

Microprocessor-controlled fire alarm panel in accordance with NF EN 54-2, NF EN 54-4, NF 

S 61-936, and NF S 61-940. Managed evacuation unit (UGA) include with it’s own security 

power supply in accordance with NF S 61-936 (1999). Connection to automatic and nonautomatic 

fire detectors, various types of esserbus transponders. The following fire detectors 

can be connected: conventional fire detectors of series 9000 and series 9200. 

Rated mains voltage 230V / 50 to 60Hz 

Voltage supply 1 x 12V / 24Ah 

Rated current 0,7 A 

Security power supply (UGA) 1 x 12V / 7Ah 

Quiescent current 200mA (with operating module front) 

Quiescent current (without display) 150mA (without operating module front) 

Maximum current drawing external user 2A 


Room atmosphere class 3k5 according to IEC 721-3-3:1994 



Colour pantone 538, light-grey 

Class of protection I according to NF EN 60950 



ECS 8000M 19”- Esser, French 

as 788297, but 19” version.

Control Panels Extinguishing system 

Extinguishing system 8010 / series 3 


788012 

Features 

• 8 detector zones for up to 30 Series 9200 and 

IQ8Quad automatic detectors each (for twodetector 

dependency up to 25 detectors) 

• 1 zone for manual alarm 

• 1 zone for emergency stop 

• 1 zone for post flooding 

• 1 zone for extinguishing system fault 

• 1 zone for blocking extinguishing system 

• 1 control input for buzzer OFF 

• 1 control input for control panel reset 

• 8 relays, monitored or floating 30V DC/2A 

• 3 relays, floating 30V DC/2A 

• 2 mains voltage relays, floating 230V AC/2A 

• All outputs are provided with fuses 

788013 

¬oq-g− 

¬oq.j− 

Extinguishing panel 8010, Series 3 w/o operating unit 

Approval: 


VdS 

Control device with integrated fire detection module for an extinguishing area in accordance 

with VdS 2496 and EN 12094-1. The extinguishing panel 8010 is an electronic control 

device for extinguishing systems with integrated fire detection module, compatible with 

Series 9200 and IQ8Quad detectors. It is additionally provided with respective detection 

zones for manual alarm, post flooding and emergency stop as well as two zones for extinguishing 

system fault. Complex control functions can be realised by using the 13 control 

groups (relays). Up to 8 extinguishing areas on the esserbus of the fire detection system 

8000 or IQ8Control can be networked via the 808615 communication transponders 

(optional). 




Battery capacity 2 Akkus per 12 V / 24 Ah 

Ambient temperature - 5°C to +45°C 

Storage temperature - 10°C to +50°C 

Class of protection I to DIN EN 60950 



Colour grey, similar to RAL 7035, blue, similar to RAL 5003 

Weight (without battery) 18.3 kg 


Accessories: 

Indicating and operating unit 788400 (stand alone operation mode required), 788615 esserbus communication 

transponder, control zone indicator and 788016 alarm counter. 

Extinguishing panel 8010, Series 3 with operating unit 

As 788012 but with 788400 operating unit. 

45 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

46 


Operating Panel Modules for 8010 series 2 and 3 

788400 

788401 

Control Panel Modules 

788016 

788016.NL 


¬ou!K− 

¬ou"N− 

¬oq1s− 

¬oq1§/OM$− 

Indicating and operating panel f. releasing control equipment 8010 series 2 and 3 

Integrated detector zone indication, can be set to status indication for control outputs. LED 

for relevant extinguishing system function indication. 

Indicating and operating panel f. releasing control equipment 8010 series 2 + 3, English 

As 788400, but english. 

Panel 8010-option with control group indicator and alarm counter 

Additional LEDs for indicating activated control outputs and mechanical alarm counter. The 

indicators are mounted to the second recess of the 8010 releasing control equipment. The 

PCB connection cable is connected to the 788400 indicating and operating panel. 

Foil with German description 

Panel 8010-option with control group indicator and alarm counter, Dutch 

Same as 788016, but Dutch version.


Software 8010 

775814 

¬n[/@− 

Programming software for extinguishing control panel 8010, Series 2 and 3 

Programming software under Windows® for the fire alarm and extinguishing panel 8010 

Series 3 and for the extinguishing system 8010 Series 2 and 3. 

Software German / English 

Compatible to: 

788010 Extinguishing control panel 8010 Series 2 

788011 Extinguishing control panel 8010, operating unit D Series 2 included 



788014 Extinguishing control panel 8010 Series 3 with operating unit 

788015 Extinguishing control panel 8010 Series 3 w/o operating unit 

788024 Extinguishing control panel 8010 Series 2 with operating unit 

788025 Extinguishing control panel 8010 Series 2 w/o operating unit 

The programming interface 769828 is necessary (no USB support) for programming. 

47 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

48 


Extinguishing control panel 8010 - 19” (3HU) 

Features Extinguishing panel as per EN 12094-1 for extinguishing zone control in complaince with 

Series 3 

• 8 detector zones for up to 30 Series 9200 or 

IQ8Quad automatic fire detectors per detector 

zone ( max. 25 detectors in two-detector 

dependency) 

Series 2 

• 8 detector zones for up to 30 Series 9000 or 

9100 automatic fire detectors per detector zone 

(max. 25 detectors in two-detector dependency) 

• 1 detector zone manual alarm 

• 1 detector zone emeregency stop 

• 1 detector zone post flooding 

• 1 detector zone blocked extinguishing system 

• 1 control input buzzer off 

• 1 control input reset control panel 

• 8 monitorable relays 30V DC /2A 

• 3 floating relays 30V DC /2A 

• 2 relays for mains voltage 230V (connection at 

the back) 

• Each output is protected by fuses 

• Electronically controlled exhauster control 

Operating unit : 

• 13 LED-indication with inscription fields for 

indicating activated outputs 

• Mechanical alarm counter 

• LED display to indicate the detector zone status 

• LED collective display 

• Keypad can be intuitively handled 

• Key operated switch for keypad activation 

• Emergency current supply 2 batteries 12V/12Ah 

(not supplied as standard) 


VdS 2496, with integrated fire detection unit and optional convenient operating and indicating 

panel. 

The slide-in concept enables space-saving, ergonomic integration into a 19-inch housing for 

installation heights of only 3 height units (13.34 cm). Peripherals are connected at the back 

of the housing via plug-in cable connections to accessible connection terminals, allowing 

convenient installation within the housing before the insert is integrated. With the communication 

transponder (Part No. 808615), a maximum of eight extinguishing control panels 

can be networked on one esserbus or powered loop in Fire Alarm Systems FACP 8000 or 

IQ8Control. Via the programming interface plugged to the front, the extinguishing panel settings 

can be adjusted to the specific requirements and information can be transferred for 

visulaising to the master fire alarm system via the loop. 




Rated current @ 24 V DC 0.7 A 

Battery capacity 2 x 12 V DC / 12 Ah 



Class of protection I- as per DIN EN 60950 




The use of heavy duty rails from the respective cabinet manufacturer is recommended for 

installation in 19-inch upright cabinets. 

Installation of multiple extinguishing panels in one upright cabinet


788024 

788024.CZ 

788024.E 

788024.GB 

788024.PL 

788024.RO 

788024.SK 

788025 

¬oq9$− 

¬oq9§/D[\− 

¬oq9§/Fn− 

¬oq9§/HC3− 

¬oq9§/QMH− 

¬oq9§/SPi− 

¬oq9§/TLS− 

¬oq:'− 

Extinguishing control panel 8010 Series 2 with operating unit - Esser, German 

Approval: 

VdS 

For connecting Series 9000 or 9100 fire alarm detectors. 

Accessories: 

788653 Connection set for panel 8010 Series 2 and 3 in 19-inch technology (3 HU), 1m 

788654 Terminal card for panel 8010 Series 2 and 3 in 19-inch technology (3 UH), 2m 

Extinguishing control panel 8010 Series 2 with operating unit - Esser, Czech 

as 788024, but Czech version. 

Extinguishing control panel 8010 Series 2 with operating unit - Esser, Spanish 

as 788024, but Spanish version. 

Extinguishing control panel 8010 Series 2 with operating unit - Esser, English 

as 788024, but English version. 

Extinguishing control panel 8010 Series 2 with operating unit - Esser, Polish 

as 788024, but Polish version. 

Extinguishing control panel 8010 Series 2 with operating unit - Esser, Romanian 

as 788024, but Romanian version. 

Extinguishing control panel 8010 Series 2 with operating unit - Esser, Slovak 

as 788024, but Slovak version. 

Extinguishing control panel 8010 Series 2 w/o operating unit 

Approval: 

VdS 

As 788024 but without operating unit. 

49 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

50 


788014 

788014.CZ 

788014.E 

788014.GB 

788014.PL 

788014.RO 

788014.SK 

788015 


¬oq/m− 

¬oq/§/D[>− 

¬oq/§/FP− 

¬oq/§/HC|− 

¬oq/§/QM*− 

¬oq/§/SPK− 

¬oq/§/TL5− 

¬oq0p− 

Extinguishing control panel 8010 Series 3 with operating unit - Esser, German 

Approval: 

VdS 

As 788024 but for connecting Series 9200 or IQ8Quad fire detectors. 

Extinguishing control panel 8010 Series 3 with operating unit - Esser, Czech 

As 788014, but Czech version. 

Extinguishing control panel 8010 Series 3 with operating unit - Esser, Spanish 

As 788014, but Spanish version. 

Extinguishing control panel 8010 Series 3 with operating unit - Esser, English 

As 788014, but English version. 

Extinguishing control panel 8010 Series 3 with operating unit - Esser, Polish 

As 788014, but Polish version. 

Extinguishing control panel 8010 Series 3 with operating unit - Esser, Romanian 

As 788014, but Romanian version. 

Extinguishing control panel 8010 Series 3 with operating unit - Esser, Slovak 

As 788014, but Slovak version. 

Extinguishing control panel 8010 Series 3 w/o operating unit 

As 788014 but without operating unit.


Accessories 

788653 

788654 

¬owV©− 

¬owW#− 

Connection set for panel 8010 Series 2 and 3 in 19-inch technology (3 HU), 1m 

Length of plug-in connection cables: 1m 

2 x 50-pin connection cable 1m D-Sub50 

1 x terminal card for top hat rail or C-rail mounting with D-Sub pin connectors 

1 x terminal card for top hat rail or C-rail mounting with D-Sub multipoint connectors 

Terminal card for panel 8010 Series 2 and 3 in 19-inch technology (3 UH), 2m 

As 788653 but plug-in connection cable with 2m length. 

51 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

52 


Extinguishing System “PanelSafe” 

761220 

Features 

• Space-saving: 19“ format with only two height 

units 

• Fast detection by means of early fire detection 

inside the 19“ cabinet 

• Effective damage minimisation via automatic 

object deactivation 

• Fast extinguishing function through direct integration 

of effective FM-200 extinguishing 

device in the cabinet 

• Easy installation and commissioning via 

assembled components 

• Easy maintenance through modular design 

• Fast and secure detection of events: by means 

of clear and well-structured LED display 

• Highest security even for huge cabinets: by 

using slave units, up to 6m 3 can be protected 

• Display power supply, CPU, common trouble, 

line 1&2 

• extinguishing agent container (pressure control), 

extinguishing fan, buzzer 

• external control, actuation loop, prealarm, main 

alarm 

• extinguishing activated, manual activation 

761221 


¬m-5\− 

¬m-6_− 

PanelSafe, 19” cabinet extinguishing, basic module (master), German 

PanelSafe is a stand alone fire detection and extinguishing system in 19” design. It is an 

extremely cost effective fire detection solution for EDP server, telecommunication devices 

and switch cabinets. The system consists of a master unit (basic device) with fire detection 

/ 2-detector dependency, control and extinguishing unit. 

The PanelSafe extinguishing system is a space-saving solution that can be easily installed 

in commercially available, closed 19” cabinets with a maximum cabinet volume of 1.2m 3 . 

Installation is also possible in huge cabinets or several connected cabinets (max. 5) when 

using additional slave modules (only extinguishing module and detection). 


Mains voltage 230V AC ± 15% 

Output voltage 24V DC, 1A for external actuation, buzzer and 

extinguishing fan 

Emergency power supply 2Ah (4h capacity) 

Detector 2 optical scattered light detectors in two-detector 

dependency 

Inputs for power supply, detector 1&2 / manual activation, 

door switch 

Outputs extinguishing fan, buzzer, external control 

Relay outputs pre and main alarm / common trouble, deactivation 

Extinguishing suppression via door switch 

Extinguishing agent Novec 1230TM , C6F12O/N2 (25 bar) 

Extinguishing agent container - volume 1.1 l for max. protected volume of 1.2m 3 

Extinguishing agent container - approval approved as per RL 1999/36/EG 

Ambient temperature 0°C to 40°C 

Weight approx.14kg 

Dimensions (W x H x D) 19 x 87 x 403.25 mm 

19” master slide-in unit, junction box with connecting cable, tank with fire-extinguishing agent 

Novec 1230TM, extinguishing fan, mains cable (2m), door switch and 2pcs. optical smoke 

detectors 

PanelSafe basic module with extinguishing fan (rear view) 

PanelSafe, 19” panel extinguishing system, slave 

PanelSafe slave for increasing the protected volume. 

Basic device (master) and slave connecting cable are required. 2 optical scattered light 

detectors in two-detector-dependency. 


Extinguishing agent Novec 1230”TM”, C6F12O/N2 (25 bar) 

Extinguishing agent container - volume 1.1 litre for max. protected volume of 1.2m 3 

Extinguishing agent container - approval approved as per RL 1999/36/EG 

Ambient temperature 0°C to +40°C 


Display via master 

Dimensions (W x H x D) 19” x 87 x 265 mm 

19” slave slide-in unit, tank with fire-extinguishing agent Novec 1230TM and 2pcs. optical 

smoke detectors


Accessories 

761227 

761228 

761226 

761230 

¬m-

54 

Control Panels CMSI - French Standard 


System Overview CMSI - French Standard


783000 

Features 

• Up to 32 CMSI 8000 can communicate using 

the network IGIS LOOP. 

783003 

¬o?!F− 

¬o?$O− 

CMSI 32 functions in cabinet 

Approval: 

CNMIS 

Security control panel 32 functions / 64 functions with extension in compliance with NF S 

61-934, NF S 61-935, and NF S 61-936. Association with a fire alarm panel NF approved. 

CMSI 8000 is an intelligent Fire Protection Control Equipement. It has been designed to 

ensure several kinds of functions such as evacuation, door control or containment, smoke 

and heat control system and so on. The CMSI 8000 can be used in public building as 

hospital, clinic, hotel, shopping center, offices for example, but also for industry or private 

offices. CMSI 8000 can be extended up to 128 functions with extension. Tested by CNPP in 

compliance with French standards NFS 61-934, NFS 61-935 and NFS 61-936. 

Type A: 

It can be connected to a FACP as IQ8Control or System 8000 using one micromodule RS 

232/TTY serial interface (Part No. 784842). 

Type B: 

Without FACP using inputs interface (Part No. 783255) to connect MCP’s. 

CMSI 8000 communicates with special intelligent transponders (MD1L, MD2L and MD4L) 

via loop modules (Part No. 783256). These transponders can be installed in the building 

close to devices to control, 2 redundant cables for the power supply. 


Operating voltage external security power supply 24 or 48V DC 

External voltage 21 to 56 V DC 

Security functions 128 max. with extension version 

Order lines 1, 2 or 4 per transponder MD 

Quantity of transponders 32 MD4L, 64 MD2L or 64 MS1L per ring loop 

Loop 2 or 4 with extension version 






Dimensions (W x H x D) 450 x 642 x 177 mm (for 32 functions) 

450 x 963 x 177 mm (for 64 functions) 

A dedicated software kit tool (Part No. 783260) for PC is necessary to comission the CMSI 

8000. 

Complete control panel including system software, Rack 8 U extension for CMSI 8000, installation 

material and manual, operating manual. Security power supply is not include. 

CMSI 8000 rack-mount 19” 32 functions 

As 783000 but 19” rack mount. Equiped to receive up to 32 security function. 


Operating voltage external security power supply 24 or 48 V DC 

Dimensions 8 HU for base + 8 HU for 32 functions 

CMSI 8000 rack-mount 19” 32 functions, Rack 8 U extension for CMSI 8000 

55 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

56 


783001 

783005 

821056 


¬o?"I− Cabinet extension for CMSI 8000 

Extension cabinet for CMSI 8000 (Part No. 783000). 

Maximum 32 additional functions for each extension. 





Dimensions (W x H x D) 450 x 642 x 177 mm (for 32 functions) 



¬o?&U− Rack 8 U extension for CMSI 8000 

¬s+Yc− 

As 783001, but Extension 19” rack mount (8U) for CMSI 8000 (783003). 

CMSI 1 function 

Approval: 

CNMIS 

Security control panel 1 function in compliance with NF S 61-934 and NF S 61-935. Association 

with a fire alarm panel NF approved. 


Rated mains voltage 230V / 50Hz 

Operating voltage 24V DC 

Available internal current 500mA 

Available current per line 6W, 250mA 24V DC with internal power supply 

48W, 2A / 24V DC with external power supply 

48W, 1A / 48V DC with external power supply 

Security functions 1 

Order lines 2 


Colour grey 

Material metallic wall housing 

Weight 5.2kg (with batteries) 

Battery 2 x 12V / 1.8Ah 


Complete control panel including system software, installation material and manual, operating 

manual. Batteries are included.


821057 

Modules CMSI 8000 

783250 

783251 

783252 

¬s+Zf− 

¬oASy− 

¬oAT|− 

¬oAU¡− 

CMSI 10 functions 

Approval: 

CNMIS 

Security control panel 10 functions in compliance with NF S 61-934, NF S 61-935, and NF 

S 61-936. Association with a fire alarm panel NF approved. 


Rated mains voltage 230V / 50Hz 

Operating voltage 24V DC 

Available current per line 1 A with external power supply 24 or 48V DC 

per line 

Security functions 10 max. 

Order lines 10 max. 

UGA function 5 max. 

Ambient temperature range -10 °C to +45 °C 

Colour grey 

Material metallic wall housing 


Weight 13kg (with batteries) 

Battery 2 x 12V / 6Ah 


Complete control panel including system software, installation material and manual, operating 

manual. Batteries are included. 

Front face 4 security functions for CMSI 8000 

Up to 8 modules in a box. 

Front face 1 alarm managed unit for CMSI 8000 

Up to 8 modules in a box 

Front face 12 functions UCMC for CMSI 8000 

Up to 8 modules in a box 

57 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

58 


783253 

783254 

783255 

783256 


¬oAV¤− 

¬oAW§− 

¬oAX!− 

¬oAY$− 

Accessories for CMSI 8000 

789907 

¬o¦(~− 

Front face 12 zones for manual call points for CMSI 8000 


Blank front face for non used place for CMSI 8000 


Internal module for MCP zones or link with fire detection panel 

12 zones module for manual call point or connection with fire alarm control panel. 

Bus CMSI 8000 

Single ring loop module for up to 128 remote control lines. Max 2 in a box or 4 with extension. 

Software package ECS 8000M - Esser, French

Power Supply Power Supply Units 60 - 61 

Voltage Converters 62 

Batteries 63 - 64 

Display and Operating 

Units Standard 65 

Serial Connection 66 

Network 67 

Fire brigade indicating 

+ operating panels 68 - 72 

59 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

60 

Power Supply Power Supply Units 

Power Supply - Housing version 

785653 


¬oYVK− 

There is a suitable power supply/charger unit available for every type of application. Each 

unit features permanent battery monitoring, voltage stabilisation and current limitation. Batteries 

used in the power supply must be tested and VdS approved. Batteries of the same age 

from the same manufacturer coming from the same production batch must be used when 

connecting batteries in parallel. Furthermore, regulations as per DIN VDE 0833-1 have to 

be adhered to. 

External power supply unit 12V DC / 2A 

Approval: 

The external 785653 power supply unit enables an uninterruptible power supply of peripherals 

in fire alarm systems and intrusion detection systems. The power supply unit complies 

with the EN, DIN and VDE standards. Batteries have a maximum capacity of 48Ah 

(space for 2 x 12V / 24Ah batteries). Relay outputs are provided for common trouble, power 

failure, battery failure and ground fault. All relays operate as floating changeover contacts. 


VdS 




Operating voltage 10.5 V DC to 14.8 V DC 


Output current max. 2 A 

Maximum battery capacity 24 Ah or 48 Ah 

Battery charging voltage 13.65 V DC @ 25 °C 

Battery charging voltage 13.65 V DC @ 25 °C 

Emergency power supply 800 mA @ 60h, 666 mA @ 72h 

Contact load relay 30 V DC / 1 A 







Weight approx. 8 kg (w/o battery) 


Accessories: 

382040 8-fuse card

Power Supply Power Supply Units 

785655 

¬oYXQ− 

External power supply unit 24V DC / 1A 

Approval: 


VdS 

The external power supply unit 785655 enables an uninterruptible power supply of field 

devices and third-party detectors. The power supply unit complies with the EN, DIN and VDE 

standards. Relay outputs are available for common trouble, power failure, battery failure and 

ground fault. All relays work as potential-free change over contacts. 

Rated voltage 230 V AC; +10%/-15% 



Operating voltage 21.0 V DC to 29.6 V DC 

Output voltage range 24 V DC 

Output current max. 1A 

Maximum battery capacity 24 Ah 

Battery charging voltage 27.6 V DC at +25°C 

Emergency power supply 400 mA @ 60h / 333 mA @ 72h 








Weight approx. 8kg (w/o battery) 


Accessories: 

382040 8-fuse card 

61 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

62 

Power Supply Voltage Converters 

781335 

Features 

• Each output is separately fused. 

781336 

Features 


¬o.D&− 

¬o.E)− 

• Direct current potentials are electrically isolated 

• Voltage interface, for instance, for operating 

transponders connected to a extinguishing 

control panel 8010 Series 3 configured for 12 

V DC operation 

• Suitable for max 1.5 mm 2 connection terminals 

• Short circuit resilient 

781337 

Features 

¬o.F,− 

• Direct current potentials are electrically isolated 

• Suitable for max 1.5 mm 2 connection terminals 

• Short circuit resilient 

DC/DC converter 12V/24V DC 

Approval: 

This converter generates 24V as power supply for special detectors. The input voltage of 

12V is taken from the fire alarm control panel or an external 12V power supply. Mounted 

inside the FACP (mounting kit 788605), this module can supply up to 4 special detectors 

with a maximum current of 125mA each or 1 special detector with 500mA. This module can 

be integrated in cabinets 120240, 788600 and 788601. Please pay attention to the primary 

current consumtion (12V) in case of mains failure. 


VdS 

Input voltage 9 - 15 V DC 

Output voltage 24 V DC ± 10% 

Maximum output current 4 x 125 mA or 1 x 500 mA (single covered) 



Type of protection IP 40 (in housing) 

Weight approx. 150 g 


DC/DC converter output voltage 

Approval: 

VdS 

This converter generates 12 V as “electrically isolated” power supply for one special 

detector. The input voltage of 12 V is taken from the fire alarm control panel or an external 

power supply. This module can be integrated in cabinets 120240, 788600, 788601, and 

788603. Please pay attention to the primary current consumption (12 V) in case of mains 

failure. 




Maximum output current 800 mA 






The module can also be used in in explosion zones for the galvanic separation of the esserbus 

voltage supply. 

DC/DC converter output voltage 24 V DC 

Approval: 

VdS 

This converter generates 24 V as power supply for one special detector. The input voltage 

of 12 V is taken from the fire alarm control panel or an external power supply. This module 

can be integrated in cabinets 120240, 788600, 788601, and 788603. Please pay attention to 

the primary current consumption (12 V) in case of mains failure. 




Maximum output current 400 mA 





Dimensions (W x H x D) 65 x 72 x 20 mm

Power Supply Batteries (rechargeable) 

018001 

018002 

018003 

018004 

018005 

018006 

018007 

018008 

018010 

Accessories 

785753 

These sealed lead storage batteries with a solid electrolyte do not require maintenance. Operation 

irrespective of position, exhaustive discharge protected, cycle-resistant, long service 

life (4–5 years) and high loading capacity. 12V DC storage batteries with a charging voltage 

of 13.8V (6 x 2.3V per cell) at + 20º C operating temperature. 

The battery technical data sheets can be made available via the KBC on request or optionally 

can be seen via the download area on the Internet. 

The batteries comply with the VDE 0833-1 regulations for hazard alarm systems and are VdS 

approved. 

According to the VdS guidelines, the batteries must be replaced every four years. This is not the 

case if the approval certificate contains other information. 

Please note that batteries must be obtained from the same manufacturer with the same manufacturing 

date and the same capacity. 

¬"q"`− Battery 12 V DC / 1.2 Ah capacity 

¬"q#c− Battery 12 V DC / 1.9 Ah capacity 

¬"q$f− Battery 12V DC / 2.6 Ah capacity 

¬"q%i− Battery 12 V DC / 6.5 Ah capacity 

¬"q&l− Battery 12 V DC / 10 Ah capacity 

¬"q'o− Battery 12 V DC / 24 Ah capacity 

¬"q(r− Battery 12 V DC / 15 Ah capacity 

¬"q)u− Battery 12 V DC / 38 Ah capacity 

¬"q+{− Battery 12V DC / 65Ah capacity 

¬oZVM− 

Accumulator / battery kit 

63 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

64 

Power Supply Batteries 

805597 


¬qX¤h− 3.6V lithium battery 

4 lithium batteries for use in wireless detector base (Part No. 805593), wireless gateway for 

detectors (Part No. 805594) and wireless universal interface (Part No. 805601/02). 

4 pcs

Display and Operating Units Standard 

Standard LED Indicator Panel 

764790 

Loop LED Indicator Panel 

804791 

¬mP{?− 

¬qP|F− 

Standard LED remote indicator panel - Esser 

Approval: 


Loop LED remote indicator panel for 32 messages - Esser 

Approval: 


VdS 

Additional indicator for up to 32 alarm, trouble or collective signals. Connection via an integrated 

32-pin terminal strip. The indicator is controlled via relay contacts or semiconductor 

outputs with positive-guided contacts in the hazard detection system. With key for lamp 

testing, integrated buzzer and easy-to-maintain terminal card. Elegant plastic housing for 

surface mounting. 

Operating voltage 10 V DC to 15 V DC 

Quiescent current @ 12 V DC approx. 1 mA 

Alarm current @ 12 V DC 380 mA 

Display 32 LED, red 

Connection terminal max. 1.5mm 2 



Relative humidity max. 95% humidity (w/o condensation) 



Colour white similar RAL 9003, 

front colour blue similar RAL 5003 



This indicator panel is not suitable for application as an initial warning device for the fire brigade. 

VdS 

As 764790 but with integrated and wired esserbus transponder 32 LED’s for operation as a 

remote indicating panel for the esserbus. For connection to the esserbus and powered loop 

in fire alarm systems 8000 and IQ8Control. 

Operating voltage range 10 V DC to 15 V DC 

Rated voltage 19 V DC, max. 42 V DC 

Quiescent current approx. 1 mA at 12 V DC 

Alarm current 380 mA 

Display 32 LED, red 

Connection terminal 1.5 mm 2 






Colour white, similar to RAL 9003; 

front colour blue, similar to RAL 5003 



Isolator (Part No. 788612) not included, please order separately. 

This indicator panel is not suitable for application as an initial warning device for the fire brigade. 

65 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

66 

Display and Operating Units Serial Connection 

Serial LCD Indicator Panels 

785103 

Features 

• Display of zone and detector status information 

of the FACP with additional text 

• Event memory for 200 messages 

• Free programming up to a max. of 4,000 additional 

texts, each with 2 x 20 characters 

• Sequential message interrogation via scroll 

keys 

• Monitoring of the serial interface 

• Internal buzzer, can be switched off via key 

• Function test of the display elements 

• Potential-free relay, programmable for the 

modes deactivated, fault, intermittent operation, 

ON-OFF operation 

785101 

785102 

785104 

785105 

785107 

785108 


¬oT$y− 

¬oT"s− 

¬oT#v− 

¬oT%|− 

¬oT&¡− 

¬oT(§− 

¬oT)!− 

LCD indicator panel - Esser, German 

The LCD indicator panel 785103 is used as an add-on device for the remote display of FACP 

status information of the System 8000 IQ8Control relating to detectors and detector zones. 

Event messages are displayed via LED collective indicators and on the 2-line LCD display 

with the associated detector zone number and a programmable additional text. Each message 

is signalled via the built-in buzzer. The buzzer can be acknowledged by pressing a 

button. 

Up to 31 LCD indicator panels can be operated on an RS 485 bus, either directly on the RS 

485 interface of the basic card of FACP 8007/8000C/8000M/IQ8Control or using a common 

RS 485 converter (e.g. RS 232/RS 485 converter 764852) on another serial interface (e.g. 

RS 232). In connection with panel 8008, only possible with RS 232/TTY micromodule 

(784842) and RS 232/RS 485 converter (764852). 

The additional texts are programmed using the tools 8000 software package and a service 

PC connected via the 769862.10 programming interface. 


Operating voltage 8.5 V to 14 V DC 


Alarm current approx. 70 mA 


Storage temperature 0°C to +50°C 





Dimensions (W x H x D) 206 x 177 x 48.5 mm 

This indicator panel cannot be used as an initial warning device for the fire brigade. 

Accessories: 

384745 Kit for flush mount 

384747 19” rack mount kit (6HU) 

LCD indicator panel - Esser, English 

LCD indicator panel - Esser, French 

LCD indicator panel - Esser, Italian 

LCD indicator panel - Esser, Spanish 

LCD indicator panel - Esser, Polish 

LCD indicator panel for system 800 - Esser, French

Display and Operating Units Network 

Networked LCD Operating Panels 

788139 

Features 

• TTY or RS 485 interface e. g. for connecting 

remote printers 

• Optional field device module with masterbox 

unit and fire brigade operating panel interface 

and three common relays, freely programmable, 

monitored, potential-free up to 24V DC 

• Programming with System 8000 customer data 

editor 

788140 

¬orHS− 

¬orIV− 

Indicating & operating panel for networked FACP (Repeater) 

ABIGA as fully functional repeater panel. Microprocessor-controlled interface for networked 

fire alarm control panels, designed for standardised display and operation as per DIN EN 54 

- 2 and DIN VDE 0833 - 2. Installation and connection to the FACP’s via the short-circuit and 

open circuit-resistant essernet system network. 


Rated mains voltage 230V / 50 to 60Hz 

Emergency power supply 2 x 12Ah, 2 x 24Ah in the extension housing 

Quiescent current 200 mA (with operating module) 

320 mA (with ¼ VGA operating module) 


Room atmosphere class 3k5 as per IEC 721-3-3:1994 



Housing ABS, 10% glass-fibre reinforced, V - 0 

Colour similar to Pantone 538, pale grey 

Weight approx. 6.5kg 


Phase-out date: 31.01.2008 

An operating module front is not supplied or included in the price and must be ordered separately. 

The essernet micro module is included in the price but must be ordered separately either 

784840 (62,5kBd) or 784841 (500kBd). 

Housing with standard rear panel and front mounting frame for operating module fronts, 

772417 basic module, 771690 power supply module, 770584 system software, 784840 (62.5 

kBd) or 784841 (500 kBd) essernet micromodule. 

Accessories: 

Operating module fronts: 7860xx, 7861xx, 7863xx, 7864xx, 7865xx, 7868xx, 7869xx 

Indicating & operating panel for networked FACP (Repeater), slim-line 

As 788139, but designed for 12V or 24V DC external power supply. 


Rated voltage 12V/24V DC 

Voltage supply external 


Weight approx. 6.0kg 


An operating module front is not supplied or included in the price and must be ordered separately. 

The essernet micromodule is included in the price but must be ordered separately, either 

784840 (62,5kBd) or 784841 (500kBd). 

Slim-line housing with standard rear panel and front mounting frame for operating module 

fronts, 772417 basic module, 770584 system software, 784840 (62.5 kBd) or 784841 (500 

kBd) essernet micromodule. 

Accessories: 

Operating model fronts: 7860xx, 7861xx, 7864xx, 7865xx 

67 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

68 

Display and Operating Units Fire brigade indicating + operating panels 

Fire Brigade Operating Panels 

784710 

764818 


¬oP+¨− 

¬mQ37− 

The fire brigade operating panel (in compliance with DIN 14661) is an add-on device for fire 

detection systems with transmission units to the fire brigade. The essential display and operating 

elements of the fire detector control panel can be found on the fire brigade operating 

panel (FBOP), allowing direct fire brigade alarm processing via the FBOP. Therefore, detailed 

guidelines for operating the control panel do not need to be provided. 

Fire brigade operating panel - Germay 

Approval: 

Suitable for connection to the FACP 80, System 8000 and IQ8Control fire alarm systems. 

Lock: rim lock case for fire brigade half profile cylinder provided on site (DIN 18252). 


VdS 

Operating voltage 10.5 V DC to 30 V DC 

Quiescent current @ 12 V DC approx. 18mA 

Alarm current @ 12 V DC approx. 75mA 

Operating temperature range 0°C to +50°C 





Weight 3.4 kg 


The fire brigade operating panel is supplied without locking cylinder (DIN 18252). It should be 

acquired in accordance with the guidelines provided by the regional fire brigade. 

Fire brigade operating panel (FBF-Ö) - Austria 

Fire brigade operating panel in compliance with ÖNORM F 3031 (2004) 

- Plain text display with 2 lines and 16 characters for each line, illuminated 

- 3 signals can be collectively indicated per LED (in operation, alarm, fault / deactivation) 

- 2 optional status LED (BFS extinguishing system actuation) 

- 3 buttons for FACP feedback 

- Direct programming at the fire brigade operating panel via serial interface 

- The additional text is displayed when using the shortcut deactivation + fault. 



Current consumption illuminated @ 12 V DC 50 mA 

Current consumption not illuminated @ 12 V DC 40 mA 


Storage temperature -10°C to+60°C 



Colour red, similar to RAL 3000 




LCD Indicator Panels 

784743 

784744 

Features 

• Inout: TTY from the internal FACP interface 

• Output: DUAL RS 485 to the FAT interface 

¬oPL¤− 

¬oPM§− 

Fire department indicating panel FAT3000 

Approval: 


VdS 

Microprocessor-controlled fire department indicating panel in compliance with DIN 14662 

as an additional indicator for fire alarm panels. Serial connection to the fire alarm panel via 

variable interfaces TTY, DUAL RS 485, RS232 and ESPA 4.4.4(on Board), conventional and 

redundant activation, plain text display with 4 x 20 characters, collective LED indication 

(alarm, trouble, deactivation). Simple handling with 4 buttons (buzzer OFF/level/scroll buttons). 

Additional text (> 5000 texts) can be programmed using a PC with serial interface 

connection, event memory, redundancy via loop structure for up to 16 FAT, power supply 

and signalling pathway are monitored to prevent short or open circuits, full functional range 

during breakdown of one circuit. The ESPA interface enables direct connection of telecommunication 

and paging systems. 



Alarm current @ 12 V DC approx. 125 mA 






Weight 3.5kg 


The module can only be used when combined with a System 8000 or IQ8Control fire alarm 

panel. 

Programming software “FatProgWin” is included. 

Adaptor module ADP-N3E 

Microprocessor-controlled module for installation in System 8000 or IQ8Control fire alarm 

panels. In compliance with DIN 14675, the TTY interface can be used for redundant transmission 

when the adaptor is connected and when the fire department indicating panel 

FAT3000 is used for initially informing the fire department. Additional text (> 5000 texts) can 

be programmed using a PC with serial interface connection. 


Operating voltage range 8V DC to 30V DC 



Connection terminal max 2 x 0.8 mm 2 

Length connection cable approx. 800 m 



Air humidity (relative)

70 


784753 

784754 


¬oPV9− 

¬oPW


Plain Text Indicator and Operating Panels 

784725 

784726 

¬oP:L− 

¬oP;O− 

FB inform./operating system, A4 horizonal layout, individual locking-German 

Sheet steel housing with two leaves for surface mount or flush mount installation with central 

leaf opening for both door leaves. The right-hand housing door can be individually 

opened by means of a built-in CL1 lock. Door opening through fire brigade locking (suitable 

for half profile cylinder installation). In the left-hand half of the housing, a 784743 fire service 

indicator panel and a fire service operating panel 784710 are installed. The housing is 

designed for receiving a transmission unit or a manual call point. The fire service indicator 

panel is actuated via the serial interface in the control panel. The fireservice operating panel 

is connected to the control panel interface. A maximum of 2 x 100 DIN A4 / horizonal layout 

fire brigade route maps can be integrated. 


Rated voltage 12V DC / 24V DC 

Quiescent current @ 12 V DC approx. 50mA 

Alarm current @ 12 V DC approx. 180mA 

Ambient temperature 0°C to +50 °C 




Weight 15kg 



Only in combination with the System 8000, IQ8Control fire detection panels. For redundant operation, 

redundancy module ADP-N3E (Part No. 784744) is required. 

Double-leaf sheet steel housing 

Fire service indicating panel 784743 

Fire service operating panel 784710 

FB inform./operating system, A3 horizonal layout, individual locking - German 

As 784725 but for a maximum of 80 DIN A3 fire brigade route maps (transverse). 


Weight 17kg 


Only in combination with System 8000 and IQ8Control fire alarm panels. 

For redundant operation, the redundancy module ADP-N3E (Part No. 784744) is required. 

71 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

72 


Accessories 

070300 

764896 


¬($!0− 

¬mQ£S− 

This elegant and functional housings are designed for storing documents for the emergency 

services. Thus, for example, layout plans, ground plans, operational procedures etc. can be 

kept safe for the relevant services. 

Emergency file depot DIN A4 horizontal layout for 2 x 64 cards, red 

For DIN A4 with electromechanical opening release via manual pushbutton. For up to 200 

fire brigade routing cards. 


Colour sheet steel, red coated, similar RAL 3000 

Weight 7.5kg 



Emergency file depot DIN A4 horizontal layout for 10 pcs. routing cards, red - German 

On the back of every emergency file depot are 4 holes and on the front side 4 bracket hooks. 

For the installation on any underground are to set out 4 flat head screws (max. 4mm Ø). 

The first emergency file depot is hooked up on the screws. Every new emergency file depot 

is mounted to the four latches and snaps in behind a metal lug 8see example of use). Each 

single emergency file deposit is mounted end-stackable on the last one so that the required 

emergency file number can be selected on the spot. 


Material sheet steel powder coated 

Colour red, similar RAL 3000 

Weight 0.73kg 


Application example with three staggered emergency file deposits.

Network Technology essernet 74 - 77 

Multiprotocol Gateway 78 - 82 

IGIS-LOOP 83 - 84 

73 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

74 

Network Technology essernet 

784840 


The essernet is a short circuit and open circuit resistant 2-wire backbone for networking fire 

detection and intrusion detection panels from Esser’s product range. The essernet permits 

both hierarchy-restricted and hierarchy-free programming of panels. The essernet has been 

tested and approved by the VdS. The hardware components are listed in the respective 

equipment approvals of the fire detection panels. 

Up to 31 panels can be networked with each other in a ring loop. Superior functions and 

functions covering different panels can be programmed. The status of the entire system can 

be read off on anything from one to all panels as desired. Likewise, the system can be operated 

entirely from one panel. 

Networking can be carried out via a simple telecommunication cable, e.g. IY-ST-Y 2 x 

0.8mm, with 784840 or using a data cable, e.g. IBM type 1 as well as CAT5 cable, with 

784841. With the essernet repeaters, cable distances of up to 3000m between two panels 

are possible. An optical waveguide fibre is possible with the converters, which are listed 

below. 

Third-party or management systems (e.g. WINMAGplus) can be connected via the serial 

essernet interface. 


¬oQI{− essernet module 62.5kBd 

Network interface module for up to 16 network users (e.g. panels respectively SEI). Protocol: 

similar to DIN 19245 - 1 (Profibus). Topology: loop structure, short circuit and open 

circuit resistant. 



Baud rate 62.5kBd 

Cable telecommunications cable I Y (St) Y n x 2 x 0.8mm 

Cable length max. 1000m between two users


784841 

784865 

784843 

784763 

¬oQJ~− essernet module 500kBd 

¬oQb_− 

¬oQL¦− 

¬oP`W− 

Network interface module same as 784840 essernet loop module, but for a maximum of 31 

network users (e.g. panels respectively SEI). 



Baud rate 500kBd 

Cable IBM type 1 or similar 

Cable length max. 1000m between two users 

essernet repeater 62.5kBd 

Approval: 


VdS 

The essernet repeater increases the maximum distance between two fire alarm control 

panels in the essernet by up to 1000 m. Standard telephone cables can be used as connection 

leads. Two repeaters can be operated in line. 


Current consumption @ 12 V DC 100 mA 

Baud rate 62.5 kBd 

Cable telecommunications cable IY(St)Y n x 2 x 0.8 mm 




Housing die-cast aluminium 

Colour grey 



essernet repeater 500kBd 

Approval: 

VdS 

As 784865 but with 500kBd baud rate. IBM type 1, type 2 or type 6 cables can be used as 

connection leads. 

The respective 784841 essernet module must be ordered separately. 

Fibre optic converter for essernet, Multi-Mode with F-ST male connection 

Fitted on locking device for C-rail mounting. Depending on the glass fibre used, distances 

of up to 3km are possible. Suitable for 50/125μm and 62.5/125μm multi-mode fibres. 



Current consumption @ 12 V DC approx. 100 mA 





Prefabricated connecting cable included for connection to the essernet module in the FACP. 

75 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

76 


784764 

784765 

784855 

Features 

• Serial data rate 19.2kBd 

• RS 485 interface on board 

784856 


¬oPaZ− Fibre optic converter for essernet, Multi-Mode with F-SMA male connection 

As 784763, but with F-SMA male connection. 

¬oPb]− Fibre optic converter for essernet, Single-Mode 

¬oQXA− 

Fitted on locking device for snap-on mounting. Interface converter electrical/optical for RS 

485 field bus networks; repeater function; for fused quartz-fibre optics, electrical full/half 

duplex operation; long range version. 


Operating voltage 18 to 32 V DC (typ. 24 V DC) 


Power consumtion @ 18 V DC 3,4 W 

Operating temperature range -25 ºC to +60 ºC 

Storage temperature range -25 ºC to +70 ºC 

Installation mounting rail or mounting plate 

Weight 650 g 


Material zinc die-cast 


Serial essernet interface EDP (unidirectional) 

The serial essernet interface can be used as a gateway to link remote computers that support 

the Esser data protocol (EDP). The EDP version (unidirectional) is only provided with 

information from the essernet, remote control is not possible.The unit includes a slot for an 

essernet module and is therefore a fully functional unit within the short circuit and open circuit 

resistant essernet. 


Operating voltage 10.5 to 28 V DC 




The essernet micromodule and the interface module are not included and must be ordered 

separately in accordance with the required essernet type and the serial transmission standard. 

Accessories: 

788606 Housing kit 

772386 Interface-Module RS 232/V24 

772387 Interface-Module TTY/CL 20mA 

784840 essernet micromodule (62.5kBd) 

784841 essernet micromodule (500kBd) 

¬oQYD− Serial essernet interface EDP (bidirectional) 

As 784855 but bidirectional.


784859 

Features 

• RS 485 interface 

Accessories 

788606 

772386 

772387 

¬oQ\M− 

¬ow'a− 

¬n8wk− 

¬n8xn− 

8000 FACP remote serial essernet interface 

The serial essernet interface is a router for interfacing an 8000 fire alarm panel over relatively 

large distances. Information from the connected fire alarm panel is received via a 

router/router link and made available in the host essernet. 

It has a slot for an essernet loop module and is thus an integral device in the short circuit 

and open circuit resistant essernet. For remote function, you can use the integrated RS 485 

interface. 

The essernet micromodule and the interface module are not included and must be ordered 

separately, depending on the type of essernet and the serial transmission mode. 

770432 SEI setup 

Accessories: 

788606 Housing kit 

772386 Interface-Module RS 232/V24 

772387 Interface-Module TTY/CL 20mA 

784840 essernet micromodule 

784841 essernet micromodule 500kBd 

Software 

Housing kit 

Housing for the serial essernet interface. 




Colour white, similar to RAL 9003 and 

front: blue, similar to RAL 5003 


Interface module RS232/V24 

For the serial essernet interface. 

Interface module TTY/CL 20mA 

For the serial essernet interface. 

77 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

78 

Network Technology Multiprotocol Gateway 


The Multiprotocol Gateway provides the conversion of essernet data protocols to standard 

software protocols for the communication with overriding building services management 

systems as well as devices from other manufacturers. The planning of the data points is carried 

out on the basis of text files per protocol driver. A connection of two data points is 

defined in a further text file via information of source and destination. The mapping of the 

data points is carried out on the basis of analog actual values, analog projected values, 

binary projected values as well as binary actual values. 

The basic configuration is carried out through simple reading of the project data from the 

tools 8000 programming software and conversion of the editable project data into data 

objects of the respective target protocol. The Gateway has an access-protected web user 

interface with its own user administration. In this way, the following are possible: remote 

diagnostics, the status inquiry of all data points and switching over the Gateway without 

additional software (when using the corresponding Esser modules). Here, alarm, fault and 

disconnection are each considered to be one information point for one fire detector. Insertion 

of an expansion card (PC104) is optionally possible. This is for communication protocol, 

for example LonTalk ® , included in the package with protocol option. 

A serial essernet interface (SEI) –uni- or bi-directional – as well as an Interface Module 

RS232/V24 is necessary for connecting the Multiprotocol Gateway to the essernet. When 

using the bidirectional SEI, switching functions such as connection and disconnection of 

detectors or detector groups is also possible. 

In addition to the essernet protocol, delivery also includes a third-party protocol listed 

further below. 

At shipping, the Multiprotocol Gateway is designed for operation at 230 V AC. 


Accessories: 

784855 Serial essernet interface EDP (unidirectional) 

784856 Serial essernet interface EDP (bidirectional) 

772386 Interface module RS232/V24 

788606 Housing kit


MPG DP500 

Features 

• Interfaces: 

- 1 X RS485 BACnet MS/TP (B+, A-, AGND, 

screen) 

- 1 X RS232 Rx, Tx, GND, RTS,CTS 

- 1 X serial port RS232 9-pin fully allocated 

- 1 X RJ45 10/100 Base-T 

- 1 X USB 

• CPU: ATMEL ARM9 200 MHz 

• RAM 32 MB SDRAM 

• Memory: 256MB Flash-RAM 

• Operating system: Linux Real-time 

• Indicators: 

- Power LED, green 

- RxD LED, yellow 

- TxD LED, yellow 

- Status LED, multi-color 

- Network media LED, orange 

- Network activity LED, green 

• 1 X digital input 

• 1 X digital output (relay 1250W) 

• Internal temperature sensor 

• Network - bias resistors, 560 Ohm (DIP switches) 

• Network – termination resistors 120 Ohm (DIP 

switch) 

785000 

785001 

785002 

785003 

785004 

¬oS!n− 

¬oS"q− 

¬oS#t− 

¬oS$w− 

¬oS%z− 

The Multiprotocol Gateway DP500 is suitable for usage in small objects in which only a 

small number of detection points must be transmitted. The maximum number of detection 

points is 330 indicating and 200 indicating and switching. Here, a fire detector is valid as a 

detection point. Because of its small dimensions and the integrated mounting rail supports, 

this device can be easily mounted into existing housing. 


Operating voltage 12-26 V DC / AC 

Power consumption 8 W 

Cooling passive 

Ambient temperature 0 °C to 50 °C 

Relative humidity 20 % to 80 % rF, non-condensing 

Weight 400 g 

Fixation top hat rail mounting support 


Power supply 

Rated voltage 100-240 V AC 

Nominal frequency 47-63 Hz 


Output current 2,5 A 

Power output 60 W 




This device is not expandable via an internal card. One RS-485 interface is already integrated. 

Multiprotocol Gateway, power supply, cross-over data cable, serial connection cable 

Multiprotocol-Gateway DP500 Esser - BACnet Client 

Multiprotocol-Gateway DP500 Esser - BACnet Server 

Multiprotocol-Gateway DP500 Esser - EIB/Instabus 

Multiprotocol-Gateway DP500 Esser - LONTalk 

Multiprotocol-Gateway DP500 Esser - Modbus IP 

79 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

80 


785006 

785007 

785008 

MPG DP1500 

Features 


¬oS'¢− 

¬oS(¥− 

¬oS)¨− 

• Interface: 

- 2 x RS232 (9pol. Sub-D) 

- 1 x Ethernet, 10/100Mbit/s, RJ-45 connection 

785009 

785010 

785011 

785012 

785013 

¬oS*"− 

¬oS+%− 

¬oS,(− 

¬oS-+− 

¬oS..− 

Multiprotocol-Gateway DP500 Esser - OPC Server 

Multiprotocol-Gateway DP500 Esser - custom driver incl. HW 

Multiprotocol-Gateway DP500 Esser - custom driver 

The Multiprotocol Gateway DP1500 is suitable for usage in small to mid-sized objects. The 

maximum number of detection points is 1000 indicating and 600 indicating and switching. 

Here, one fire detector counts as one detection point. Because of the integrated mounting 

rail supports, this device can be easily mounted into existing housing. 







Power supply 

Rated voltage 120 to 370 V DC / 85 to 264 V AC 

Nominal frequency 47-63 Hz 

Output voltage 5 V (tolerance 2%) 

Output current 5 A 

Weight approx. 0,5 kg 








Multiprotocol-Gateway DP1500 Esser - Modbus IP


785015 

785016 

785017 

MPG DP7500 

Features 

• Interface: 

- 4 x RS232 9-pol (optional Com4 RS485 

optoisolated) 

- 1 x RJ45 100/10 Base-T 

- 1 x RJ45 1Gbit Base-T 

- 4 x USB 

• CPU: Pentium M 800MHz 

• RAM: 512MB DDR-RAM 

• Memory: 40GB HD, optional DiscOnChip 

• Operating system: QNX 

785018 

785019 

785020 

785021 

¬oS04− 

¬oS17− 

¬oS2:− 

¬oS3=− 

¬oS4@− 

¬oS5C− 

¬oS6F− 



Multiprotocol-Gateway DP1500 Esser - custom driver 

The Multiprotocol Gateway DP7500 is suitable for usage in mid-sized objects. The 

maximum number of detection points is 5000 indicating and 3000 indicating and switching. 

One fire detector counts here as a detection point. This device is ready for back plane mounting 

and can be integrated into existing upright cabinets. 


Operating voltage 10 to 30 V DC 


Cooling passiv 

Ambient temperature 5°C bis 50°C 

Relative humidity 5 % to 90 %, non-condensing 


Fixation back plane mounting 


Power supply 

Rated voltage 100 to 240 V AC 



Output current 2.5 A 

Power output 60 W 


Fixation back plane mounting 







81 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

82 


785022 

785024 

785025 

785026 

MPG DP3500 

Features 

• Interfaces: 

- 2 x RS232 9-pol 

- 1 x RJ45 100/10 Base-T 

- 4 x USB 

• CPU: Intel PIII 1100MHz MMX 

• RAM: 256MB SDRAM 

• Memory: 64MB non-volatile medium (Flash) 

• Operating system: QNX 

785027 

785028 

785029 

785030 

785031 

785033 

785034 

785035 


¬oS7I− 

¬oS9O− 

¬oS:R− 

¬oS;U− 

¬oS^− 

¬oS?a− 

¬oS@d− 

¬oSBj− 

¬oSCm− 

¬oSDp− 


Multiprotocol-Gateway DP7500 - OPC Server 

Multiprotocol Gateway DP7500 Esser - custom driver incl. HW 

Multiprotocol Gateway DP7500 Esser - custom driver 

The Multiprotocol Gateway DP35000 is suitable for usage in large objects. The maximum 

number of detection points is 23,000 indicating and 14,000 indicating and switching. One 

fire detector counts here as a detection point. This device is constructed for upright cabinets 

with 19” slide-in unit and requires 4 rack units of free space for mounting. 






Relative humidity 20 % to 80 %, non-condensing 

Cooling active 

Display Power LED and status LED 


Fixation 19” slide-in unit 

Dimensions (W x H x D) 19” x 4 HE x 281 mm 

Integrated power supply 

Multiprotocol Gateway, cross-over data cable, serial connector cable 








Multiprotocol-Gateway DP35000 Esser - custom driver

Network Technology IGIS-LOOP 

013330.10 

013331.10 

013332.10 

788604 

¬"B?§/214− IGIS-LOOP-Controller 

For IDT/FDT/AC/PC. 

Interface controller of universal use for integrating intrusion detection and fire detection 

units in the IGIS-LOOP. The controller allows WINMAG control centre PCs to be connected 

to the IGIS-LOOP via the integrated RS-232 interface, thus setting up an extensive security 

system. 

¬"B@§/217− IGIS-LOOP-Controller (in housing ZG0) 

In housing ZG0. Housing with sealed door. 

No space for emergency power supply. 

¬"BA§/21:− IGIS-LOOP controller (in housing ZG2) 

¬ow%[− 

In housing ZG2. Housing with sealed door. 

Space for emergency power supply item no. 010686.01, or 010690.02 (EN54) and 1 x storage 

battery . 

IGIS-LOOP controller kit kit for FACP 8008 

For operating the 8008 fire alarm control panel in the IGIS-LOOP system network. Complete 

kit with IGIS-LOOP adapter micromodule, connection cable and IGIS-LOOP controller ready 

for installation in the S1E housing and for connection to the FACP 8008. 



Quiescent current @ 12 V DC adapter micromodule 85mA 

IGIS-Loop controller 200mA 

The number of System 8000, IQ8Control as well as IACP 5008 / 5008C control panels depends 

on the system load, which must be calculated. Please contact our technical marketing department 

for system laod calculation. 

1 x 784847 Serial interface for WINMAGplus / WINMAGLite 

1 x 750725 Connecting cable IBB for Backbone 

1 x 013330 IGIS-LOOP controller 

83 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

84 

Network Technology IGIS-LOOP 

788609 

789305 

784847 


¬ow*j− 

¬o~&l− 

IGIS-LOOP controller kit for FACP 8000M, IQ8Control M 

For operating the 8000M, IQ8Control M fire alarm control panel in the IGIS-LOOP system 

network. Complete kit with IGIS-LOOP micromodule, connection cable and IGIS-LOOP controller, 

pre-mounted on a carrier plate, ready for installation and for connection to the FACP 

8000M, IQ8Control M. 



Quiescent current @ 12 V DC adapter micromodule 85 mA 

IGIS-Loop controller 200 mA 



for system load calculation. 

1 x 784847 IGIS-LOOP adapter module 



1 x 742417 PCB mounting rail 

IGIS-LOOP controller kit for FACP 8000C, C IQ8Control or EMZ 5008C 

For operating 8000C and IQ8Control fire alarm control panels and/or 5008C intruder alarm 

panel in the IGIS-LOOP system network. Complete kit with IGIS-LOOP adapter micromodule, 

connection cable and IGIS-LOOP controller, mounted in extension housing, ready for 

connection to a FACP 8000C, IQ8Control or an intrusion alarm panel 5008C. 



Quiescent current @ 12 V DC adapter micromodule 85 mA 

IGIS-Loop controller 200 mA 

Emergency power supply up to 2 x 12 V DC / 24 Ah 





Housing ABS, 10% glass fibre-reinforced, V -0 



for system load calculation. 

1 x 789300 Battery extension housing 

1 x 784847 IGIS-LOOP adapter module 



1 x 742417 PCB mounting rail 

¬oQP)− Serial interface for WINMAGplus / WINMAGLite 

Interface suitable for serially connecting 800X/IQ8Control fire alarm panels to WINMAGplus/WINMAGLite. 

The module is plugged to the essernet slot in the control panel. As a 

result, essernet operation is disabled. 

For PC connection, the RS 232 isolator module 784754 is required. 



Quiescent current @ 12 V DC 85 mA 

Interface RS 232 

The control panel is connected to the PC via RS 232 cable, which is not supplied as standard.

Management systems WINMAGplus 86 - 97 

WINMAGLite 98 - 99 

85 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

86 

Management systems WINMAGplus 

Features 

• Compatible with Windows XP Professional SP2, 

Windows of 2003 servers and Windows Vista 

• Modular construction and freely programmable 

• Direct control of the network devices 

• List of measures to be taken for fire-fighting 

forces 

• Individual allocation of usage rights - priority 

scheduling 

• Integrated simulation-functions 

• Extensive recording of events and operations 

• Visualization of messages 

• Up to 12 active graphics simultaneously representable 

• Integration of video sequences possible 

• Information output via Windows print manager to 

multiple printers etc. 

• Time program / calendar function 

• Integrated database standard 

• Activation of other programs from WINMAGplus 

possible 

• Efficient programming language (SIAS) for 

customer-specific adjustment of interface and 

processes in case of alarm 

• Remote control possible via modem (optional) 

• 10 printers per workstation possible 

• Multiple monitors can be used. 4 of 8 screens 

may be selected. 


Windows management system for hazard detection systems 

Windows management system for hazard detection systems. 

WINMAGplus has been specially developed to meet the requirements of managing and integrated 

hazard detection systems on a single PC platform. 

WINMAGplus simultaneously manages and displays graphically a number of security applications, 

using a common user interface including: fire detection technology; voice alarm 

public address; intrusion detection technology; access control technology; video technology; 

rescue route technology/escape door control, personnel protection systems and locating 

systems as well as fence monitoring systems. 

Apart from security systems, a multitude of building management control systems such as 

lighting, elevator control and fault detection systems as well as door/gate/barrier control 

systems can be managed and graphically displayed. 

Database and user interface are designed in line with current standards: messages are 

displayed both graphically and in text format. 

WINMAGplus offers various application options, ranging from clearly displayed messages 

to active control of all detection devices. 

Based on our security networks IGIS-Loop and essernet, WINMAGplus is not only a highly 

professional system but also the best possible integrated visual data and management 

solution. 

Programme: 

Thanks to its modular design, WINMAGplus offers suitable software for systems of any size 

and type of application, ranging from WINMAGplus basic package for single-station 

systems with one subsection being connected to the WINMAGplus multi-station system 

with multiple subsections being connected. 

Licensing enables the programme options purchased and it legitimises programme use. A 

dongle is acquired together with a licence. The dongle must be plugged into a parallel interface 

or into a USB port of the WINMAGplus computer. 

With multi-station systems, every computer that is networked must be equipped with a 

dongle. Workstations that are not networked do not need a dongle. 

The licence is for one version level (until version 7). If updating is effected to versions prior 

to V6.0 to V10.0 and later versions, you automatically receive a dongle. If the dongle is 

removed during operation, WINMAGplus runs for max. 72 hours in online mode. 

Our services for installers: 

Our WINMAGplus services include everything from entering alarm points to generating diagrams. 

First of all, operators are made familiar with WINMAGplus. Then we work out the 

specifications together with the customer and develop SIAS programmes. We design complete 

application packages and train your personnel. Until the final acceptance, we offer support 

for all installation processes and assist you during daily operation via a remote maintenance 

tool if required. 

Interfaces, drivers: 

Besides our security system drivers included in our product catalogue, we offer a variety of 

drivers for all kinds of trades and manufacturers. Due to the continuously rising number of 

drivers, the current list of drivers can be requested when required. If the driver you need is 

not available, we will develop a driver geared to your requirements. Alternatively, all instruments 

can be connected via the standard OPC interface. This is an international standard, 

which is supported by a multitude of manufacturers irrespective of their product lines. For 

developing your own drivers, we can provide you with the Connection Server and a developer’s 

package. Thus, individual WINMAGplus drivers can be created. 

Hardware and software requirements: 

Pentium 3 GHz or higher, minimum 512 MB RAM, minimum 1 GB of hard disk space, XGA graphics 

card with minimum 4 MB video memory, monitor with min. 1024x768 pixels, sound card 

with external speakers, Windows XP Professional SP 2 Windows of 2003 servers and Windows 

Vista, Internet Explorer version 6.0 or higher. 

To order WINMAGplus licenses, please use the order form found in the back of the catalogue.


013610.10 

Basic Licences 

013631.10 

013630.10 

013633.10 

¬"E+§/21e− Control center software CD WINMAGplus basic kit 

¬"E@§/21=− 

¬"E?§/21:− 

¬"EB§/21C− 

WINMAGplus control centre software CD for hazard detection systems, licence not included, 

compatible with Windows XP Professional SP2, Windows of 2003 servers and Windows 

Vista.With the aid of this basic software and the corresponding licenses, hazard detection 

systems can be operated and managed via PC.Hazard reports are indicated in text form and 

graphically. In this way, the PC can also be used as an electronic emergency control point.As 

of WINMAG version 10, this version can be used as an upgrade (only for existing WINMAG 

versions 6 or older). 

For demonstration purposes only, the WINMAGplus basic version operates without a licence as 

afull version for a total of twenty 8-hour days, after which the programme switches to offline 

mode. After expirary of the test time, all connections to all components are cut off. Starting in 

offline mode does not reduce the number of test runs.The demo mode is a full-function editing 

environment. All components function except the online communication. Each process can also 

be tested in demo mode through simulation and all editing functions can be used. 

Please use order form printed in the catalog. 

You can also download this software free of charge from our protected download area at 

www.esser-systems.com. 

Basic license for WINMAGplus USB port 

This basic licence is used to activate the basic software package / demo version to operate 

as unrestricted visualising software for server workstations and for network clients. For 

interfacing control panels to server workstations, further licences are required (see 

013601.10 – 013606.10, 013608.10, 013611.10-013613.10, 013625.10). 


Dongle for USB port 

Basic license for WINMAGplus parallel port 

Basic licence for WINMAGplus control centre software including dongle for the parallel 

port. 

This basic licence is used to activate the basic software package / demo version to operate 

as unrestricted visualising software for server workstations and for network clients. For 

interfacing control panels to server workstations, further licences are required (see 

013601.10 – 013606.10, 013608.10, 013611.10-013613.10, 013625.10). 


Dongle for parallel port 

Basic license for USB port 3 month duration 

Dongle with USB port for licencing of the software. The data medium contains the licence 

information as well as the activation of the program options FDS, AC, FT and video. 

The term is restricted to 3 months. 

A one-time extension for a further 3 months is possible (part no. 013634.10). 


Dongle for USB port and license disk 

87 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

88 


Upgrade Package 

013634.10 

013616.10 

013617.10 

Extension Licences 

013609.10 


¬"EC§/21F− 

¬"E1§/21w− 

¬"E2§/21z− 

¬"E*§/21b− 

Basic license extension for USB port 

Licence file for extending the duration of 013633.10 an additional 3 months (only possible 

once). 


License disk 

WINMAG upgrade to WINMAGplus 

Upgrade of a WINMAG installation from version 6 onto the newest WINMAGplus control 

center software. 

For updating WINMAG V1 - 5 please use part no. 013617.10 in order form. 


License file 

WINMAG upgrade as of version 6 to WINMAGplus 

WINMAG installation upgrade to the most recent WINMAGplus control centre software 

version 

An existing WINMAG as of version 6 can be upgraded to the most recent WINMAGplus control 

centre software version. For each installation with dongle (each connected PC) an 

upgrade version must be separately ordered. 

Please indicate the basic licence number when ordering! 


WINMAGplus control centre software - subsequent upgrade 

This order number serves as an auxiliary number for a subsequent optional extension or 

(e.g. additional client or subsequent connection of video systems) to an existing WINMAG 

installation from V 6.0. to V10 and WINMAGplus. The appropriate licences must be ordered 

separately. The dongle need not be submitted. 

Note on the respective licenses: 

In each case only one license is necessary in order to connect an unlimited number of control 

panels to a PC. These licences may be separately (subsequently) ordered only in conjunction 

with the auxiliary number 013609.10. The update number of the basic licence must be indicated. 


This article must be indicated during expansion and is not charged for.


013601.10 

013626.10 

013603.10 

013604.10 

¬oP^Q− 

¬"E;§/21.− 

¬"E$§/21P− 

¬"E%§/21S− 

WINMAGplus Licence - intrusion detection technology 

Licence option for WINMAG/WINMAGplus basic software. Required if intrusion detection 

systems are connected to WINMAG. 

This licence may be ordered separately (subsequently) only in conjunction with the auxiliary 

number 013609.10. The update number of the basic licence must be included when ordering. 

The license is used for connection of the Honeywell intrusion detection systems MB/HB, 5008. 

Please use the attached order form. 

WINMAGplus licence - fire detection technology 

Licence option for WINMAG/WINMAGplus basic software. Required if fire detection 

systems are connected to WINMAGplus. 

This licence may be ordered separately (as subsequent optional upgrade) only in conjunction 

with the auxiliary number 013609.10. The update number of the basic licence must be included 

when ordering. The license is used for connection of the Honeywell IQ8Control, system 8000 

1024 and 1016 fire detection systems. 


WINMAGplus License - access control 

Licence option for WINMAG/WINMAGplus basic software. Required if access control 

system devices are to be connected to WINMAGplus (e.g. ACS 2 and ACS 8). MultiAccess 

and/or IQ MultiAccess software package is also required. 

This licence may be ordered separately (as a subsequent optional update) only in conjunction 


when ordering. The license is used for the connection of the Honeywell ACS and (IQ) MultiAccess 

access control systems. 


WINMAGplus Licence - video technology 

Licence option for WINMAG/WINMAGplus basic software. Required if video technology 

equipment is to be operated via WINMAG. The crossbars can execute such commands as 

pan, zoom, tilt, select monitor etc., depending on the model. The following video crossbars 

are currently supported: Ernitec M 500 and M 1000; Honeywell MaxPRO 32; Philips LTC 

8x00; Fusion series II / III; Geutebrück Vicrosoft; Geutebrück Multiscope; Honeywell Fusion; 

contact your supplier for additional brands. 



when ordering. 


89 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

90 


013605.10 

013623.10 

013608.10 

013654.10 

013656.10 


¬"E&§/21V− 

¬"E8§/21%− 

¬"E)§/21_− 

¬"EW§/21¤− 

¬"EY§/21!− 

WINMAGplus Licence - rescue route technology/escape door control 

Licence option for WINMAG/ WINMAGplus basic software. Required if rescue route technology 

/ escape door control equipment (only Honeywell Security) is to be operated via 

WINMAG. 

The status of escape doors is graphically displayed. 



when ordering. The license is used for connecting Honeywell rescue route technology/escape 

door control equipment. 


WINMAGplus License - interfacing DEZ 9000 

Option for connecting the DEZ 9000 remote control unit to the WINMAG/WINMAGplus 

system. The connection also enables the installation of applications working on the basis of 

VdS- 2465 transmission protocols to the WINMAGplus system. 


WINMAGplus Licence - RTD 

Licence option for WINMAG/WINMAGplus basic licence. Enables operation of WINMAGplus 

via modem, using DS 7600 and DGA 2400 to ESSER IDT (HB and MB series) and fire detection 

systems (1024 series). 





WINMAGplus Licence – CMSI 

Licence for WINMAG/WINMAGplus basic software for the French market. 





WINMAGplus Licence nurse call systems 

Optional for WINMAGplus basic software. Required if to be connected to WINMAGplus call 

system devices (e.g. clino phon 99). 

This license can be ordered separately (as a subsequent optional expansion) only in conjunction 

with the auxiliary number 013609.10. The update number of the basic license must indicated. 

The license is used for the connection of Ackermann clino systems. 


Not available until the end of Q4/2008


013657.10 

Connection Server 

013606.10 

013607.10 

OPC 

013590.10 

013618.10 

¬"EZ§/21$− 

¬"E'§/21Y− 

¬"E(§/21\− 

¬"D{§/21§− 

¬"E3§/21}− 

WINMAGplus Licence VA/PA 

Optional for WINMAGplus basic software. Required if to be connected to WINMAGplus 

VA/PA systems, e.g. Esser Variodyn D1. 

This license can be ordered separately (as a subsequent optional expansion) only in conjunction 

with the auxiliary number 013609.10. The update number of the basic license must indicated. 

The license is used for the connection of Esser Variodyn D1 systems. 


WINMAGplus Licence connection server 

Licence option for WINMAG/WINMAGplus basic software. Connection Server is a software 

module that enables the connection of a 3rd party device to WINMAGplus . Connection 

Server offers a convenient interface with which data and control commands can be 

exchanged bi-directionally in detection point format using WINMAGplus. 





Connection server developers kit 

This developers kit can be used to programme WINMAG/WINMAGplus connections to third 

party devices. The package contains the Connection Server Developers Kit including full 

documentation plus a one day training in Albstadt. 


Dongle for USB port and license file 

Universal gateway for PC (software) 

Gateway software as a standalone solution for the allocation of data points on host control 

centre systems via OPC, ESPA 4.4.4. 

Hardware and software reuirements: 

Pentium 3 GHz or higher, min. 512 MB RAM , min. 1 GB hard disk, XGA graphics card with 

min. 4 MB video memory, monitor with 1024 x 768 pixels or more, sound card with external 

speakers, Windows XP Professional SP2 and Windows 2003 Server, Windows Vista, Internet 

Explorer 6.0 or higher. 

Part no. 013590.10 may only be ordered in connection with part no. 013618.10. 


Data points package 

Package of 500 data points for project-related allocation of OPC tags, ESPA data points, etc. 

The data points package can only be ordered in connection with the License 013590.10 Universal 

Gateway for PC and/or License 013611.10 OPC Server. 


91 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

92 


013611.10 

013612.10 

Options 

013405.10 

Features 


¬"E,§/21h− 

¬"E-§/21k− 

¬"C&§/21R− 

• Serial interface: RS232, RS422 or RS485 (2and 

4-wire), configurable via software 

• Transmission speed: 300 bauds to max.230 

Kbaud configurable via software 

• Serial connection: D-Sub 25, socket 

Ethernet interface: 10Base-T/100Base-TX 

• Transmission speed: 10/100/auto MBit, configurable 

via software 

• Mode of transmission: half- /full-duplex or 

automatic, configurable via software 

• Network access: RJ45 

• Supported protocol: ARP, UDP, TCP, ICMP, 

Telenet, TFTP, AutoIP, DHCP, HTTP, SNMP, TCP, 

UDP and Telnet, TFTP 

WINMAGplus Licence – OPC server 

Option for WINMAG/WINMAGplus basic software. Required if WINMAGplus is to act as an 

OPC server. 

The OPC server licence can only be ordered in conjunction with the 013618.10 licence. This 

licence may be ordered separately (as a subsequent optional update) only in conjunction with 

the auxiliary number 013609.10. The update number of the basic licence must be included 



WINMAGplus Licence – OPC client 

Option for WINMAG/WINMAGplus basic licence. This is required if WINMAG is to display 

data from devices with OPC interfaces. 





Hardware Option TCP/IP converter, Ethernet RS232/RS485 

This hardware option is used for the connection of an remote Essernet via a (for example) 

companies-wide Ethernet LAN to a WINMAGplus control centre via TCP/IP. Through this, 

the device is used as a protocol converter between the SEI contained on the Essernet and 

the WINMAGplus control centre available in the Ethernet LAN. 


Rated operating voltage 9 -30 V DC or 9 - 24 V AC 

Power consumption 1,5 Watt, maximum 

Operating temperature 0°C to 60°C 

Storage temperature -40°C to 85°C 

Material metal 

Weight 0,20 kg 


Dimensions (L x W x H) 9 x 6,4 x 2,3 cm 

System requirements for operation and software configuration: Windows® 2000 / XP.


013613.10 

013650.10 

013651.10 

013652.10 

013660.10 

¬"E.§/21n− 

¬"ES§/21v− 

¬"ET§/21y− 

¬"EU§/21|− 

¬"E]§/21-− 

Option - notification 

Licence option for WINMAG/WINMAGplus basic licence. Required if SMS (text message), 

fax or e-mail are to be sent from WINMAGplus. 



when ordering. An ISDN connection (S0) as well as an ISDN card are required for the notification 

function. 


Option – escalation 

Option for the WINMAG/WINMAGplus basic licence. Required if short text messages dispatched 

by WINMAGplus are to be acknowledged. Without acknowledgment, pre-programmed 

escalation plans can be activated. 



when ordering. For the escalation licence, the 013613.10 notification licence is required. A PC 

sound card is required for this function. 


Option – DTMF control option 

Option for the WINMAG/WINMAGplus basic licence. Facilitates the execution of control 

sequences via dual tone multi frequency (DTMF). With this, for example, it is possible to 

switch system outputs connected to WINMAG on or off via mobile phone. 





Option – ability for customized interface rights (client-side) 

Option for the WINMAG/WINMAGplus basic licence, allowing individual assignment of interfaces 

and rights to several operators. 





Option – WEBX 

Licence option for the basic WINMAG/WINMAGplus licence, allowing display of all system 

statuses via Internet or Intranet, using standard browsers (max. 5). 





93 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

94 


013624.10 

013625.10 

013640.10 

013619.10 

013653.10 


¬"E9§/21(− 

¬"E:§/21+− 

¬"EI§/21X− 

¬"E4§/21¢− 

¬"EV§/21¡− 

Option – redundance 

Option for redundant connection of essernet and IGIS-Loop security networks to the WIN- 

MAGplus server. Interface operation for redundant networks is based on master/backup 

operation and prevents data loss in WINMAGplus objects in case of disruption of network 

connections caused by cable defects or COM port failure. 


Option – Client 

Licence option for WINMAG/WINMAGplus basic licence. Enables operation of one client station 

in a computer network with one server workstation. The licence must be installed at the 

server workstation. Clients require only the WINMAGplus software to be installed. One WIN- 

MAGplus client licence is needed per client. 





WINMAGplus - remote-access package 

With this remote-access package, WINMAG/WINMAGplus applications can be remotely serviced 

and supported via modem. The package includes four-hours of telephone support 

within the first twelve months. 

No modem is included with the package and and must be provided in accordance with the existing 

transmission technology. 

Please use the attached order form. 

WINMAGplus – translation tool 

Option for WINMAGplus basic software. With this tool, the WINMAGplus database can be 

translated into other languages. 





WINMAGplus – 4-monitor support option 

Option for WINMAGplus basic licence. Enables the allocation of 4 monitors from a choice 

of 8 monitors. This option only works with WINMAGplus. 

This option requires a special graphics card with up to 8 outputs in the WINMAG hardware. 

This option must be ordered per workstation which uses the multi-monitor option. 

Please use order form printed in the catalog.


013655.10 

013614.10 

Services 

784830.10 

784832.10 

784833.10 

784839.10 

¬"EX§/21§− 

¬"E/§/21q− 

¬oQ?§/218− 

¬oQA§/21>− 

¬oQB§/21A− 

¬oQH§/21S− 

WINMAGplus – AutoCAD option 

Option for WINMAGplus basic licence. Enables the placement of detectors and groups 

directly from ACAD LT. The drawings are saved as dxf files. The detectors/ groups are placed 

as hyperlinks in the ACAD drawing and stored. When importing these ACAD drawings into 

Winmagplus, the symbols of the disciplines are automatically placed onto the correct position 

in the drawing. An ACAD licence must be provided by the customer. 

This option only works with WINMAGplus. 


Not available until th end of Q4/2008 

WINMAGplus – OEM option 

Option for WINMAGplus basic software for customizing WINMAGplus to individual 

customer-specific wishes. 

May cause changes to symbols / text and the front end. 

These licences may be ordered separately (as a subsequent optional update) only in conjunction 

with the auxiliary number 013609.10. The update number of the basic licence must be 

included when ordering. 


Detection point input 

Object-related according to written customer specifications. 

Text page input 


Graphics page input 


Graphics page conversion 

Conversion of various graphics formats into format readable for WINMAGplus. 

95 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

96 



Application Example


Application Example 

97 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

98 

Management systems WINMAGLite 

013635.10 


¬"ED§/21I− 

Features 

• Cost-effective management software for hazard 

detection systems 

• Visualising and controlling of only one hazard 

detection central control panel (FDS, VAPA, 

IDS, RRT, AC) 

• Visualising and controlling of VisiOprime or 

Fusion video management systems 

• Management of up to 500 detection points 

• Processing of up to 100 status reports per 

second 

• Processing of up to 100 macro processes 

• Connection of log and alarm printers 

• Information display via monitor and / or printer 

(Windows standard printer) 

• Adjustable programme background 

• Flexible, window-oriented graphics 

• Display and location of detectors in diagrams 

• Status information indicators 

• Pre-defined alarm reports 

• Simulation function 

• Extensive event and operation logging 

• Users possible 

013636.10 


WINMAGLite with USB dongle 

WINMAGLite is a cost effective first step to hazard detection systems management. Ease of 

operability as well as pre-defined, practical central control panel and detection point types 

facilitate the commissioning and operation of WINMAGLite. 

WINMAGLite is perfect for small systems for which no expansions or connection of further 

hazard detection control panels are planned in the near future. Thus, the Lite version is perfectly 

suitable for a broad range of applications, even for WINMAGplusprofessionals. 

Especially small objects can be professionally secured due to a combination of hazard 

detection system with the Honeywell video management systems of Honeywell VisiOprime. 

WINMAGLite provides the user with almost all basic WINMAGplus functions. Unlike the full 

version, this version can initially connect only one hazard detection central control panel. 

The user has access to pre-defined programmes which can automatically be adjusted via a 

text editor to the respective situation on site. 

The alarm stack which was implemented in previous WINMAGplus versions is replaced 

through symbols displayed in the top bar which indicate alarms. The new feature improves 

overall clarity so that the user can react more quickly in the case of an alarm. 

Hardware and software requirements: 

Pentium processor 3 GHz or higher, min. 512 MB RAM , min. 1 GB hard disk, XGA graphics 

card with min. 4 MB video memory, monitor with 1024 x 768 pixels or more, sound card with 

external speakers, Windows XP Professional SP2, Windows 2003 Server and Windows Vista, 

Internet Explorer 6.0 or higher. 


Training for this product is offered. Please contact our training department. 

Basic CD control centre software package WINMAGplus (013610.10) 

Accessories: 

Please take note that one serial interface for WINMAGLite, Part No. 784847 is needed. 

¬"EE§/21L− WINMAGLite upgrade to WINMAGplus full version 

If the WINMAGLite system limits have been reached, an upgrade to the full version of Winmagplus 

is possible, since both systems have access to the same database. WINMAGplus 

options are not part of the upgrade and must be ordered separately. 

WINMAGplus options are not included in the upgraded version and must be ordered separately. 

Please use order form printed in the catalog.

Management systems WINMAGLite 

Difference between WINMAG Lite and WINMGplus 

99 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

100 


Automatic Detectors Detector Series 9000 


Series IQ8Quad 

(Intelligent addressable) 104 - 115 

Detectors for Hazardous Areas 116 - 119 

Detector Base Series 9x00 120 

Base Series IQ8Quad 121 

Accessories 122 - 136 

101 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

102 

Automatic Detectors Detector Series 9000 Conventional 

Features 

• Detector series preferably for connection to thirdparty 

control panels 

• Detector series can be used with all Esser fire 

alarm panels 

• All detectors without switch-on-control 

• Green marking on housing for heat detectors 

• Up to 30 detectors can be connected per zone 

• Rated voltage UN = 9V 

• Low closed-circuit current 

• The detector alarm current can be programmed 

for the adaptation to other manufacturer’s panels 

• Large operating voltage range 

• Detector design based on SMD technology 

• All detectors can be programmed on one primary 

loop 

• Standard detector base 781590, detector base 

781588 with relay output (30V / 1A) or detector 

base 781592 with optocoupler output (30V / 

0.4A) can be used for all Series 9000 detectors 

• Easy installation 

• Pre-mounting plate with snap-in adapter 

• Detector base with base adapter 781498 up to IP 

43 

• Optional detector lock 

• Detector removal tool for max. 9m mounting 

height 

• Reverse polarity protected 

761162 

761162.F0 

761262 


¬m,_q− 

¬m,_§/G1c− 

¬m-_s− 

Automatic conventional fire detectors with high reliability used for premises and items of 

property with low and medium concentration of valuable assets. 

The detector alarm current can be adjusted for 12V zone voltage to max. 50mA by means 

of connecting a resistor of 1kohm to max. 62ohm located between terminals 4 and 5. 

Resistor value can be calculated with the following formula: R = 2.4V / (I alarm - 9.4mA) 


Operating voltage 8 V to 28 V DC 

Alarm current @ 9 V DC typ. 9 mA 

Display red LED / light pipe 


Air humidity 95 % rel. humidity (without condensation) 

Material ABS 


Weight approx. 90g 

Dimensions (Ø xH) 90 x 61 mm (72 mm including base) 

Type of protection IP 40, IP 43 with base adapter 781498 

Detector bases are not supplied as standard. 

Fixed heat detector 

Approval: 

Automatic heat detector with fast semiconductor sensor for the detection of fires with 

extreme fluctuations in ambient temperatures. Conventional heat detector without switchon-control, 

with alarm latch and alarm indicator. 


VdS 

Quiescent current @ 9 V DC approx. 12 μA 

Application temperature -20°C to +50°C 

Area to be monitored max. 30 m 2 

Height to be monitored max. 7.5 m 

Detector specification DIN EN 54 - 5, Class 1 

Fixed heat detector - Esser, France 

Approval: 


CNMIS 

Height to be monitored max. 4m 

Alarm current (UN) 19mA 

Application temperature 58°C 

Rate-of-rise heat detector 

Approval: 


rapidly rising temperatures and integrated fixed temperature function for the detection of 

fires with slowly rising temperatures. Conventional detector without switch-on-control, with 

alarm latch and alarm indicator. 


VdS, LPCB 





Detector specification EN 54 - 5 A1

Automatic Detectors Detector Series 9000 Conventional 

761262.VC0 

763262.F0 

761362 

761362.VC0 

763362.F0 

771365 

¬m-_§/WD1.− Rate-of-rise heat detector - Esser, China 

¬mA_§/G1&− 

¬m._u− 

Rate-of-rise heat detector - Esser, France 

Approval: 


CNMIS 

With fault information on optical smoke detector. 

Area to be monitored max. 50m 2 


Detector fault current (UN) 8,3mA 

Optical smoke detector 

Approval: 


VdS, LPCB, CNBOP 

Optical scatter detector for the early detection of fires with clear smoke development. Conventional 

smoke detector without switch-on-control, with alarm latch and alarm indicator. 





Height to be monitored max. 12 m 

Detector specification DIN EN 54 - 7 

¬m._§/WD10− Optical smoke detector - Esser, China 

¬mB_§/G1(− 

Optical smoke detector - Esser, France 

Approval: 

CNMIS 

¬n.b¡− Optical smoke detector non-latched alarm - Esser 



Mounting height max. 12m 

Voltage 8 to 28 V DC 

Nominal input voltage 9 V DC 

Quiescent current approx. 20 μA, plused 

Alarm current 9 to 50 mA programmable 

Temperature range -20 °C to +72 °C 


Humidity class ¥ 95 % rel. humidity, (no condensation) 

Protective tube IP 40 

Material ABS plastic 

Colour white (similar to RAL 9010) 


Dimensions (with base) Ø 90 mm, H = 72 mm 

103 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

104 

Automatic Detectors Series IQ8Quad (Intelligent addressable) 


Automatic intelligent fire detectors with high reliability, used for premises and items of property 

with medium and high concentration of valuable assets. 

Detector series IQ8Quad features: 

System advantages 

- designed for optimal operation on System 8000 and IQ8Control fire alarm systems 

- with multisensor detectors for the detection of all types of fires, even under the most 

difficult operating conditions 

- detector with and without loop isolator 

Different options of installation 

- wiring in loop and spur combination, e.g. 

- maximum number of detectors with cable lengths of up to 3500m with installation 

cable for fire detection, e.g. cables I-Y(St)Yn x 2 x 0.8mm 

- up to 127 detectors per loop installation 

- up to 127 detector zones per loop installation 

- up to 32 detectors per zone 

Easy commissioning 

- automatic detector addressing 

- fixed address assignment of detector location, even after detectors have been 

replaced or added 

- localication of wire breaks and short circuits on loop 

- detector-LED used as alarm indicator and as an indicator for detectors in service 

- adaptation to changing operating conditions 

- dedicated LED for indicating operation (green LED) 

- disconnection of individual detectors, detector zones and detection areas 

- disconnection of individual sensors or several sensors at once within a 

multisensor detector; either manually or depending on programmed time of the day 

Automatic adaptation to varying environmental conditions 

- compensation of changing levels of air pressure, humidity, smoke concentration 

according to the double chamber principle 

- electronic compensation of long-term influences like aging or pollution 

Reliable detection 

- constant alarm sensitivity of multisensor detector for all types of fire 

- large signal to noise ratio due to the special design of the sensors and the electronics 

to suppress electromagnetic interference 

Reliable false alarm suppression 

- high immunity against false alarms by means of timed evaluation of different sensor 

criteria 

- signal patterns not typical for fires are eliminated by using special filter algorithms 

- automatic self-monitoring of detector electronics 

- continuous loop monitoring even during short-circuits through isolating the relevant 

segment 

- automatic monitoring of all sensors to guarantee operational capacity and correct 

condition. 

Increased operating reliability 

- short-circuit and wire break tolerant through monitoring from both ends of the loop 

- alarm decision inside detector 

- fail-safe circuit activated if communication fails 

Maintenance 

- automatic maintenance request 

- heat detector identification through a black circle on the light transmission plate 

- multisensor gas detector identification through a golden loop on the circle transmission 

plate 

- operating time counter in each detector 

- alarm counter in each detector 

- fault counter in each detector 

- automatic, cyclic loop check 

- complete status interrogation from the control panel 

- interrogation of operating data from all detectors on loop via standard service PC and 

detector interface 

Comprehensive range of accessories 

- standard detector base and relay base 

- base adapter for ceiling mounting 

- dust cover for fire detector or detector base 

- kit for suspended ceiling mounting 

- RF base 

WAGO clamps for looping in wires, e.g. type 243-204 (Ø 0.5mm - 1mm) or 273/104 (0.75mm 2 

- 2.5mm 2) can be mounted on the detector base. 

Commission, test and maintain fire detectors only with panel software V2.42R006 and higher 

and the programming software, tools 8000 V1.05 and higher! 

The detector base is not supplied as standard.


Detector without integrated alarm device 

802171 

802171.F 

802177 

¬q6h=− 

¬q6h§/G&− 

¬q6nO− 


Emergency operation alarm approx. 18 mA 

Air speed 0 to 25.4 m/s 


Relative humidity 95 % rel. humidity (without condensation) 

Type of protection IP 43 (with base + option) 




Dimensions (Ø x H) 117 x 49 mm (including base 62 mm) 

Special-colour on demand 

The detectors Part No. 802271, 803271, 802371, 803371, 802373, 802374 and 

803374 are approved in the scope of the DIBt system authorization for the operation 

with an Automatic Door System. 

without socket! 

Fixed heat detector IQ8Quad 

Approval: 



Automatic heat detector with fast semiconductor sensor to guarantee reliable detection of 

fires with strong heat generation. Intelligent fire detector with decentralised intelligence, 

automatic function self-test, CPU failure mode, alarm and operating data memory, alarm 

indicator, soft-addressing and operating indication. 

The detector is provided with an integrated isolator. A parallel detector indicator can be connected. 






Detector specification EN 54 - 5 A1S 

Special marking for heat detector on the light pipe: black ring. 

Fixed heat detector IQ8Quad - France 

Approval: 

CNMIS 

As 802171, but with NF-Approval Mark at the backside. 

Fixed heat detector class B IQ8Quad 

Approval: 


VdS 

As 802171, but for increased operating temperature according to EN 54-5 Class B. 






Detector specification EN 54-5 BS 


105 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

106 


802271 

802271.F 

803271 

802371 


¬q7h?− 

¬q7h§/G(− 

¬qAhS− 

¬q8hA− 

Rate-of-rise heat detector IQ8Quad 

Approval: 

Automatic heat detector with fast semiconductor sensor to guarantee reliable detection of 

fires with rapidly rising temperatures and integrated fixed temperature function for the 

detection of fires with slowly rising temperatures. Intelligent fire detector with decentralised 

intelligence, automatic function self-test, CPU failure mode, alarm and operating data 

memory, alarm indicator, soft-addressing and operating indication. 

The detector is provided with an integrated isolator. A parallel detector indicator can be connected. 



Operating voltage range 8 to 42 V DC 





Detector specification EN 54-5 A1R 


Rate-of-rise heat detector IQ8Quad - France 

Approval: 

CNMIS 


IQ8Quad Rate-of-rise detector without loop isolator 

Approval: 

VdS, CNBOP, LPCB 

As 802271 but without loop isolator. 

The detector can be operated in a standard detector group as well as independently. 

Optical smoke detector IQ8Quad 

Approval: 

Optical smoke detector to guarantee safe and early detection of fire. Intelligent fire detector 

with decentralised intelligence, automatic function self-test, CPU failure mode, alarm and 

operating data memory, alarm indicator, soft-addressing and operating indication. The 

detector is provided with an integrated isolator. A parallel detector indicator can be connected. 








Detector specification EN 54-7


803371 

802375 

802375.F 

802373 

¬qBhU− 

¬q8lM− 

¬q8l§/G6− 

¬q8jG− 

IQ8Quad Optical smoke detector without loop isolator 

Approval: 


As 802371 but without loop isolator. 


OT blue multisensor detector IQ8Quad 

Approval: 


VdS 

Multisensor with integrated optical detector and heat detector. The optical measurement 

chamber is provided with a newly developed sensor technology, enabling the detection of 

open fires, smouldering fires and fires with high heat generation. Especially for open fires, 

the classical ionisation technology implemented in ionisation detectors is replaced by the 

new detection technology. The detector is capable of identifying the TF1 and TF6 test fires 

described in the EN 54-9:1982 specification. 

The OT blue multisensor is an intelligent detector with time-related signal analysis, signal correlation 

of the sensor data, decentralised intelligence, automatic function self-test, CPU failure 

mode, automatic adaptation to environmental conditions, alarm and operating data 

memory, alarm indicator and soft-addressing. 

The detector is provided with an integrated isolator and a parallel detector indicator can be 

connected. 






Detector specification EN 54-7/5 A2, CEA 4021 


OT blue multisensor IQ8Quad - France 


OT multisensor detector IQ8Quad 

Approval: 


VdS 

Multisensor detector with integrated optical detector and heat detector, with time-controlled 

signal analysis and weighted data combination of both detector functions for detecting 

smouldering fires and fires with extreme heat generation. Intelligent detector with decentralised 

intelligence, self function test, CPU redundancy mode, automatic adaptation to the 

environments, alarm and operating data storage, alarm indication and soft addressing. 

The loop isolator is integrated in the detector. A parallel detector indicator is additionally 

attachable. 








107 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

108 


802374 

802374.F 

803374 

802473 


¬q8kJ− 

¬q8k§/G3− 

¬qBk^− 

¬q9jI− 

O 2T multisensor IQ8Quad 

Approval: 

Multisensor detector provided with two built-in optical smoke sensors with different scattered 

light angles as well as additional heat detector sensor evaluation to guarantee the 

detection of different types of fire from smouldering fires to open fires with constant sensitivity 

level. Smoke sensor signal identification to ensure smoke classification and reduction 

of deceptive alarms caused, for instance, by water vapour or dust. 

Because of its excellent detection characteristics, the detector is also able to identify the 

standardized TF1 and TF6 test fires. The O 2T multisensor detector is also suitable for applications 

with higher temperatures of up to +65 °C. The detector is provided with an integrated 

isolator. A parallel detector indicator can be connected. 







Detector specification EN 54-7/5 B, CEA 4021 

OTG multisensor (CO) IQ8Quad 

Approval: 

Multisensor detector with integrated smoke detector, heat detector and gas sensor (CO) for 

preventive and early detection of fires ranging from smouldering fires to open fires through 

combined evaluation of scattered light, temperature and gas. An alarm is actuated at carbon 

monoxide (CO) concentration levels that are life-threatening for humans. Programmable 

technical alarm if CO concentration level is exceeded.The detector is provided with an integrated 

isolator. A parallel detector indicator can be connected. 



O 2T multisensor IQ8Quad - France 


IQ8Quad O 2 T Intelligent detector without loop isolator 

Approval: 


As 802374 but without Loop isolator. 


VdS 








CO pre alarm approx. 75 ppm 

CO alarm approx. 100 ppm 

In the course of installation, we recommend testing the integrated CO sensor with our CO test 

gas (Part No. 805583) or CO capsule (Part No. 805553). 

Gas sensors (CO) mainly react to the carbon monoxide arising from a fire (CO). They have, 

however, also a cross sensitivity to other gases, as for example hydrogen (H2), acetylene 

(C2H2) or nitric oxide (NO). 

Special marking for gas detector on the light pipe: black ring.


Detector with integrated alarm devices 

Features The IQ8Quad smoke detectors with built-in alarm device incorporate up to 4 different functionalities 

depending on the type of detector: 

Detection 

• The reliable O 2T multisensor principle for 

consistent response performance at the 

highest level of security against false alarms 

Flash lamp 

• External power supply is not required 

• No additional short address 

• Automatic synchronisation of various 

IQ8Quad alarm signalling devices 

• High flash energy 

Sounder 





• Maximum sound level: 92 dB(A) at 1m 

• Maximum sound pressure can be set 

• Multiple signal pattern can be combined to 

one signal 

• Signal pattern and repetition rates can be set 

• 20 different signal tones, incl. DIN-tone 

Speech message with sounder 





• Maximum sound level: 92 dB(A) at 1m 

• Maximum sound pressure can be set 

• Multiple signal patterns can be combined to one 

signal 

• Signal pattern and repetition rates can be set 

• 20 different signal tones, incl. DIN-tone 

• Speech messages can be played in up to 5 

languages 

• 5 alarm messages per languages are 

preprogramed 

- fire detection as per EN 54-7 

- integrated heat sensor as per EN 54-5 

- optical alarm via flash lamp 

- acoustic alarm via sounder as per as per EN 54-3 

- acoustic alarm speech messages 

Detection 

Multisensor detectors with two built-in optical smoke sensors with different scattered light 

angles as well as additional heat detector sensor evaluation for detecting everything from 

smouldering fires to open fires with consistent response performance. Smoke sensor signal 

identification to ensure smoke classification and reduction of false alarms caused, for 

instance, by water vapour or dust. Each detector is provided with an integrated isolator. 

Alarm signalling 

The alarm signalling device is activated by the control panel. No further short address needs 

to be allocated. It is programmed with tools 8000 as of software version 1.05. 

Alarm tone / speech message programming 

For detectors with speech message and / or alarm tone function with up to five language 

options, up to 4 signals can be programmed. Two signals are reserved for alarm signalling 

and evacuation in the case of fire. Two further signals can be programmed for other events. 

Each signal can consist of up to four signal components, enabling one signal to be programmed 

as a DIN tone combined with subsequent speech messages in three different 

languages. 

Alarm tones can be chosen from a table with various tone types. For application in schools, 

a break signal to signify the breaks between class can be activated. 

Four different speech messages, each in three languages, are available: 

- “An incident has been reported in the building. 

Please await further instructions.” 

- “Attention please. This is an emergency. 

Please leave the building by the nearest available exit.” 

- “This is a fire alarm. Please leave the building immediately by the nearest available exit.” 

- “This is a test message. No action is required.“ 

When the basic setting is selected, signals / signal components can be continuously repeated 

until the signalling function is interrupted by the control panel. They can also be programmed 

with a repetition rate of one to three times. Thus, the break signal in schools can 

be deliberately set to only one repetition. In the same way, the total signal can be set to continuous 

repetition, with the DIN tone being played only once while subsequent speech messages 

are played up to three times. 

Sound pressure programming 

The sound level [dB(A)] can be set to eight levels, from approximately 64dB (A) to approximately 

92dB (A). 



All IQ8Quad detectors with built-in alarm devices can only be operated on the powered loop. 

For physical reasons, an increased sound level leads to a higher current consumption rate of 

the alarm device, the respective load factor must be considered when calculating the maximum 

number on the loop. Altogether up to 127 bus devices per loop can still be connected. 

Please consider that an extra training is required when dealing with IQ8Quad with built-in alarm 

device. The training includes installation planning and commisioning techniques. For further 

information take a look at our training brochure. Information concerning the calculation can be 

found in the “Project Planning Support“ chapter. 

109 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

110 



List of the standard for each of those language 

IQ8Quad/IQ8Alarm tone table


Detector with integrated alarm devices 








Response temperature 79°C to 88°C (@ 1°C/min) 

Relative humidity max. 95% humidity (without condensation) 


Material ABS 


Weight 145 g 

Dimensions (Ø x H) 117 x 59 mm (incl. base 65 mm) 


The 769836 demo package is available for presentations. Further data can be viewed in the 

accessories section for automatic detectors. For calculating the battery capacity of fire alarm 

control panels, the detector data “quiescent current @ FACP battery” can be added. 

Special-colours on demand! 

It is not possible to use the detector base with relay contact (Part No. 805591). 

Detector bases are not supplied as standard. 


111 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

112 


802382 

802383 

802384 


¬q8sb− 

¬q8te− 

¬q8uh− 

O/So optical smoke detector IQ8Quad 

Approval: 

O/So optical smoke detector IQ8Quad with integrated sounder 

Scatter smoke detector for safe and early detection of smouldering fires with light smoke 

generation. Intelligent detector with decentralised intelligence, automatic function self-test, 

CPU failure mode, alarm and operating data memory, alarm indicator, soft-addressing and 

operating indication. The detector is provided with a loop isolator. 

Along with smoke detection components, the detector is provided with a built-in sounder. 


VdS 

Quiescent current at UN approx. 80μA 

Sound pressure 64dB (A) to 92dB (A), 8 sound levels can be set 

Sound level +/- 2 dB (A) fo 1m for DIN tone 

Load factor 2 

O 2T/F multisensor IQ8Quad 

Approval: 

O 2T/F multisensor IQ8Quad with integrated flasher 

In addition to smoke detection with the conventional O 2T multisensor technology, the 

detector is provided with a built-in flash lamp. 


VdS 

Quiescent current @ 19 V DC 75 μA 

Quiescent current @ FACP battery 400 μA 

Load factor 2 

Flash light red 

Energy of light approx. 3 J 

Strength of light max. 15,8 cd peak / 2,63 cd effective 

Not suitable for application in relay base 805591! 

O 2T/So multisensor IQ8Quad 

Approval: 

O 2T/So multisensor IQ8Quad with integrated sounder 


detector is provided with a built-in alarm signalling device. The sound level can be set to 

eight different levels. 


VdS 



Load factor 2 

Sound level 92 dB (A), +/- 2 db (A) @ 1m for DIN tone 

Alarm signal specification EN 54-3 

Not suitable for application in relay base 805591!


802386 

802385 

802385.SV98 

802385.SV99 

¬q8wn− 

¬q8vk− 

¬q8v§/TW:9¦− 

¬q8v§/TW::&− 

O 2T/Sp multisensor IQ8Quad 

Approval: 


VdS 

O 2T/Sp multisensor IQ8Quad with integrated sounder and speech 

In addition to smoke detection with conventional O 2T multisensor technology, the detector 

is provided with a built-in voice alarm device. It can be set to eight different levels. 



Load factor 3 

Sound level 92 dB (A), +/- 2 db (A) @ 1m for DIN tone 


Not applicable in relay base 805591! 

Programmed with 5 standard national languages (DE/GB/FR/ES/IT). 

O 2T/FSp multisensor IQ8Quad 

Approval: 


VdS 

O 2T/FSp multisensor IQ8Quad with integrated flasher, sounder and speech 


detector is provided with a built-in voice alarm device. It can be set to eight different levels. 



Load factor 3 

Sound level max. 92 dB (A), +/- 2 db (A) @ 1m for DIN tone 


Flash light red 

Energy of light approx. 3 J 

23Strength of light max. 15,8 cd peak / 2,63 cd effective 

Not suitable for application in relay base 805591! 


O 2T/FSp multisensor detector IQ8Quad with composition of other languages 

Approval: 

VdS 

As with 802385, but with an individual combination of national languages. 

When ordering, please note the “Ordering information for IQ8Quad and IQ8Alarm” printed in the 

appendix. Cancellations or returns are not possible. 

Not for usage in Relay Base 805591! 

Programmed with an individual combination of up to 5 national languages. 

O 2T/FSp multisensor detector IQ8Quad 

Approval: 

VdS 

As 802385, but with individual text and/or sounds. 

When ordering, please note the “Ordering information for IQ8Quad and IQ8Alarm” printed in the 

appendix. Costs for the recording of customer-specific texts and/or tones can be obtained by 

request. Cancellations or returns are not possible. 

Not for usage in Relay Base 805591! 

Programmed according to customer specifications. 

113 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

114 


IQ8Quad Ex (i) Explosion-proof series 



General detector data according to ATEX: 

Max. Input voltage (Ui) 21 V 

Max. Input current (Ii) 252 mA 

Max. Output current (Io) 10 mA 

Max. internal capacity (Ci) 1nF 

Ambient temperature (Ta) -20 °C to +70 °C 

No. of Examination Certificate request 

Category II 2G (with Ex safety barrier Part No. 764744) 

Explosion protection Ex ib IIC T4 

General detector data: 



Air speed 0 bis 25.4 m/s 


Air humidity max. 95% humidity (without condensation) 


Material ABS 

Colour white, similar RAL 9010 


Dimensions (Ø x H) 117 x 49 mm (incl. base 62 mm) 

Additional detectors for the explosion zones can be found in the chapters Manual Call Points 

and Special Detectors. Detailed information about installation and operation can be found in the 

documentation article no. 798920. 

All of the following IQ8Quad explosion-proof fire detectors must be operated with the 805590 

base. In the case of operation in standard zones, no individual addressing is possible! 

The security barrier part no. 764744 must be used for usage in Zone 1 and Zone 2! The security 

barrier separates intrinsically safe and non-intrinsically safe circuits before the explosionprone 

area to be monitored (explosion zone). 

The detector base is not included with the delivery of the detectors. 

Application example


803271.EX 

803371.EX 

803374.EX 

¬qAh§/FY"− 

¬qBh§/FY$− 

¬qBk§/FY-− 

IQ8Quad Rate-of-rise Detector Ex (i) 

Approval: 

Automatic heat detector with quick semiconductor sensor for the reliable recognition of fires 

with fast rate of temperature rise as well as integrated fixed temperature heat function for 

the recognition of fires with slow temperature rise. Intelligent fire detector with decentralized 

intelligence, automatic function self-test, emergency mode, storage of alarm and operating 

data, alarm display. Soft addressing and separate operational display is only possible 

when operating an esserbus / esserbus-PLus IQ8Quad detector without loop isolator, especially 

for usage in explosion zones. Operation as standard detector at security barrier 

764744. 


request 



Height to be monitored max. 7,5 m 

Area to be monitored max. 30 m² 

Detector specification EN 54-5 A1R 

Special marking for heat detector on light pipe: black ring 

Available for delivery in Q2/2009 

Accessories: 

805590 Standard detector base for IQ8Quad 

IQ8Quad Optical Smoke Detector Ex (i) 

Approval: 


request 

Scattered-light smoke detector for reliable early recognition of fires. Intelligent fire detector 

with decentralized intelligence, automatic function self-test, emergency mode, storage of 

alarm and operating data, alarm display. Soft addressing and separate operational display is 

only possible when operating an esserbus / esserbus-PLus IQ8Quad detector without loop 

isolator, especially for usage in explosion zones. Operation as standard detector at security 

barrier 764744. 

Quiescent current @ 19 V DC ca. 50 μA 




Detector specification EN 54-7 


Accessories: 


IQ8Quad O 2 T Intelligent Detector Ex (i) 

Approval: 

Intelligent detector with two integrated optical smoke sensors with different scattered-light 

angles as well as additional heat detector sensor evaluation for the recognition of smouldering 

fires up to open fires with uniform characteristics. Comparison of the heat sensor signals 

for smoke classification and reduction of deceptive alarms, e.g. from steam or dust. 

Due to its excellent detection characteristics, the detector is also able to recognize TF1 and 

TF6 test fires, described in the standards. The O 2 T intelligent detector is also suitable for a 

higher operating temperature of up to +65 °C. Intelligent fire detector with decentralized 

intelligence, automatic function self-test, emergency mode, storage of alarm and operating 

data, alarm display. Soft addressing and separate operational display is only possible when 

operating an esserbus / esserbus-PLus IQ8Quad detector without loop isolator, especially 

for usage in explosion zones. Operation as standard detector at security barrier 764744. 


request 

Quiescent current @ 19 V DC ca. 60 μA 






Accessories: 


115 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

116 

Automatic Detectors Detectors for Hazardous Areas 

Intrinsically safe detector 



General detector data according to ATEX: 

Max. Input voltage (Ui) 21 V DC 

Max. Input current (Ii) 252 mA 

Max. Output current (Io) 10 mA 

Ambient temperature (Ta) - 20 °C to + 70 °C 

No. of Examination Certificate TÜV 03 ATEX 2326 

Category II 2G (with safety barrier Part No. 764744) 

Explosion protection Ex ib IIC T4 

General detector data: 

Operating voltage 9 V DC / 17 V DC addressing voltage 


Alarm current approx. 9 mA, pulsed 


Air humidity ¥ 95 % rel. humidity, (no condensation) 


with mounting plate : IP 42 / 

with mounting plate : IP 42 

With base adapter : IP 43 

Material ABS 


Weight aprrox. 90 g 

Dimensions (Ø x H) 90 x 72 mm (with detector base) 

Further detector for application in hazardous areas can be found in the “MCP’s and Special 

Detectors” chapters. 

Detailed information about installation and operation are documented in the documentation 

(Part No. 798913). 

The following ex detectors must be operated with detector bases 781590 . 

Individual addressing is not possible! 

For application in zone 1 and zone 2, the safety barrier (Part No. 764744) must be used. The 

security barrier separates intrinsically safe circuits from non-intrinsically safe circuits outside 

the hazardous area (ex area) that must be monitored. 

The detector base is not provided as standard. 

Application example


766062 

766061 

766063 

¬m]_l− 

¬m]î− 

¬m]ò− 

Ex Fixed heat detector 1161, Series 9100 

Approval: 


VdS 


extreme fluctuations in ambient temperatures. Diagnostic detector with alarm latch and 

alarm indicator, especially designed for use in hazardous areas. Operation as standard 

detector at security barrier 764744. 




Detector specification EN 54-5 A1 


Accessories: 


Ex Rate-of-rise heat detector 1261, Series 9100 

Approval: 


VdS 


rapidly rising temperatures and with fixed temperature heat function for the detection of 

fires with slowly rising temperatures. Diagnostic detector with alarm latch and alarm indicator, 

especially designed for use in hazardous areas. Operation as standard detector at 

security barrier 764744. 




Detector specification EN 54-5 A1 


Accessories: 


Ex Optical smoke detector, Series 9100 

Approval: 


VdS 

Automatic optical scatter detector for the early detection of fires with light smoke generation. 

Diagnostic detector with alarm latch and alarm indicator, especially designed for use in 

hazardous areas. Operation as standard detector at security barrier 764744. 






Accessories: 


117 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

118 


766064 

Ex-Accessories 

764744 

764745 


¬m]ar− 

¬mPM¥− 

¬mPN¨− 

Ex OT-multisensor detector, Series 9100 

Approval: 

Multisensor detector with built-in optical smoke and heat sensors with time-related signal 

analysis and signal correlation of both sensors for identifying smouldering fires and fires 

with extreme heat generation. Diagnostic detector with alarm latch and alarm indicator, 

especially designed for use in hazardous areas. Operation as standard detector at security 

barrier 764744. 


VdS 






Accessories: 


Ex safety barrier for intrinsic safe of detectors Series IQ8Quad and 9100 

Design certificate BAS01 ATEX 7005 in accordance with directive 94/9/EC 

Ex safety barrier for the operation of intrinsically safe IQ8Quad Ex (i) series detectors in connection 

with the Detector Base 805590 as well as the 9100 Ex (i) series in connection with 

the Detector Base 781590. 


Dimensions (W x H x D) 12.5 x 115 x 110mm 

A safety barrier does not replace an overvoltage protection according to IEC 801, 

DIN VDE 0185 and 0855. 

VdS approval is not required. 

You can find more detailed information on the installation and the operation in the documentation 

- Part No. 798920 for IQ8Quad Ex (i) Series detectors 

- Part No. 798913 for 9100 Ex (i) Series detectors. 

Isolation and assembly block for safety barrier 

For insulated (earth-free) mounting of 764744 barriers onto standard C rail.


764752 

Housing for ex barrier 


Features Mounting material 

• chemically resilient 

• temperature resilient 

• flame retardant 

• noncorrosive 

• sea water resistant 

• nonhalogen, UV resistant 

764754 

¬mPU4− 

¬mPW:− 

Polyester-Housing for the insatallation of up to max. 10 ex barriers with integrated inside 

mounting rail. Also for operational application under extreme environmental conditions suitably. 

Housing glass-fiber reinforced polyester 


Type of protection IP 66/67 


Threaded cable connection for housing 764752 

Threaded cable connection for housing 764752. 


Colour blue, similar to RAL 9005 

Material Polyamid 

Operating temperature -20°C to +95°C 


Cable diameter 4 -8 mm 

Threaded M16x1,5 

119 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

120 

Automatic Detectors Detector Base Series 9x00 

781590 

781590.F0 

781588 

783590.F0 


¬o0{h− Standard detector base series 9x00 

Standard base for detector series 9000, 9100 and 9200, terminal for remote LED indicator 

(detector series 9000 requires adapter module 781487). 

In conjunction with this standard detector base, 9100 Ex (i) series fire detectors can be operated 

exclusively without individual addressing (function as standard series 9000 detectors). 

An esserbus transponder for fire alarm systems (e.g. Part No. 808614) is required for 

connection to the Series 8000 / IQ8Control fire alarm system. The use of the EED module 

(Part No. 784381) is not permissible. 





Dimensions (Ø xH) 89 x 22 mm 

Cable entry on the side or through bottom plate. 

Safety barrier installation 

The safety barrier (Part No. 764744) must be installed as close as possible to the ex area that is 

monitored (zone 1), for example in a housing (Part No. 764752) or in other suitable locations. 

The safety barrier earth must be connected to the equipotential bonding system (EBS) of the ex 

area. 

¬o0{§/G1Z− Standard detector base series 9000 - Esser, France 

¬o0yb− Detector base with relay contact for series 9000 

Detector base with relay output, specially designed for Series 9000 detectors. No option for 

two detector dependency. 


Contact load 30 V DC / 1 A DC 





Cable entry on the side or through the bottom plate. 

¬oD{§/G1¤− Standard detector base series 9000 - Esser, France

Automatic Detectors Base Series IQ8Quad 

805590 

805591 

Wago clamps for looping in wires, e.g. type 243-204 (Ø 0.5mm - 1mm) or 273-104 (0.75mm 2 - 

2.5mm 2) can be mounted on the detector base. 

¬qX{S− Standard detector base for IQ8Quad 

Standard IQ8Quad detector base for the series IQ8Quad. When removing the detector, the 

loop is automatically closed. The base features a protective function against detector 

removal, which can be used if required. 




Maximum relative humidity max. 95% (without condensation) 

Connection terminal Ø 0.6 mm to 2 mm2 Material ABS 



Dimensions (Ø x H) 117 x 24 mm (including detector 62 mm) 


Wago clamps for looping in wires, e.g. type 243-204 (Ø 0.5mm - Ø 1.0mm) or 273-104 

(0.75mm 2 - 2.5mm 2) can be mounted on the detector base. 

¬qX|V− Detector base with relay contact for IQ8Quad 

IQ8Quad detector base with relay contact output. Contact: floating NO or NC contact selectable 

via jumper. Settings on site: NO contact. 


Relays floating, NC / NO option 

Contact load 30 V DC / 1A 

Current drain 5 μA (w/o detector, active relay) 



Maximum relative humidity max. 95% (without condensation) 

Connection terminal Ø 0.6 mm to 2 mm2 Material ABS 



Dimensions (Ø x H) 117 x 24 mm (including detector 62 mm) 


Wago clamps for looping in wires, e.g. type 243-204 (Ø 0.5mm - 1.0mm) or 273-104 

(0.75mm 2 - 2.5mm 2) can be mounted on the detector base. 

Not suitable for application with IQ8Quad with integrated alarm device type 802383, 802384, 

802385 and 802386 as well as 802385.SVxx! 

121 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

122 

Automatic Detectors Accessories 

Series 9000 / 9200 

781495 

781495.F0 

781496 

781497 

781497.F0 


¬o/¢u− 

¬o/¢§/G1g− 

¬o/£x− 

¬o/¤{− 

¬o/¤§/G1m− 

Surface mount adapter for series 9x00 

Surface mount adapter for premounting cables, with protection against dripping water and 

clips for locking detector bases 781588, 781585, 781592, 801593 and 781590 as well as 

RAS 782103. Installation: clip onto board 781495 or use 2 screws / 60mm space, e.g. 4.0 

x 30 DIN 96/plug S 6. 






Dimensions (Ø x H) 89 x 20 mm (10 mm increase with detector) 

Surface mount adapter for series 9x00 - Esser, France 

Detector locking for series 9x00 

Protection against unauthorised detector removal for low ceilings with up to H = 3 m. Installation 

in detector bases 781588, 781592, 781585, 781588 and 801593. According to the 

design approval, the locking is required for ionisation smoke detectors. 






In connection with adapter 781495, the protection level against dripping water is reduced. 

10 pcs 

Flush mount base adapter for series 9x00 

Adapter for mounting in ceilings and on suspended ceilings, with protection against dripping 

water and clips for locking detector bases 781590 to 781594 and 801593, the mounted 

base is flush with adapter vent. Maximum plate thickness of 20mm for suspended ceiling 

mounting. 






Rosette ø = 120mm, thickness = 3mm 

Ceiling opening ø min = 95mm for conventional keyhole saws 

Installation depth T = 55mm 

Flush mount base adapter for series 9x00 - Esser, France


781498 

781498.F0 

769803 

781487 

789855 

¬o/¥~− 

¬o/¥§/G1p− 

¬m¥$n− 

¬o/x]− 

¬o¥X>− 

Surface mount base adapter for series 9x00 

Surface mounted base adapter for application with screwed cable glands or cable conduits 

with protection against dripping water, with 3 cable entries PG 11 and clips to lock detector 

bases 781585, 781590 and 801593. 






Dimensions (Ø x H) 110 x 47 mm, 80 mm pitch 

Surface mount base adapter for series 9x00 - Esser, France 

Detector dismounting tool for series 9000/9100/9200 

With the help of this special tool, detectors belonging to series 9000 / 9100 / 9200 can be 

opened and dismounted for cleaning by authorised installation staff. 

For ionisation smoke detectors see national regulation for protection against radiation! 

Adapter module for base 781590 

Auxiliary wiring for detector base 781590 for connecting parallel indicators 761803, 

761813, 781804 and 781814. 


Dimensions (WxH) 38 x 8mm for each module 

This adapter module is exclusively designed for the operation with the standard fire detector 

base (part no. 781590) planned in connection with series 9000 detectors. 

10 pcs 

Detector cover for detectors Series 9x00 with base adapter 

For detectors with base adapters 781497 and 781498 for protecting the detectors against 

contamination during construction or renovation works. 

50 pcs 

123 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

124 


789856 

Series IQ8Quad 

805588 

805589 

805587 


¬o¥YA− 

¬qXyM− 

¬qXzP− 

¬qXxJ− 

Detector cover for detectors Series 9x00 and/or base 

For detectors with base, suitable for protecting the detectors against contamination during 

construction or renovation works. 

50 pcs 

Detector cover for IQ8Quad without built-in alarm sounder 

The cover plate protects the IQ8Quad detector against contamination during construction or 

renovation works. 

The detector covers can only be used for IQ8Quad fire detectors without built-in alarm sounder! 

Application only for detector types with Part Nos: 802171, 802271, 802371, 802374, 802375 

and 802473. 

50 pcs 

Detector cover for IQ8Quad with built-in alarm sounder 

The cover plate protects the IQ8Quad detector against contamination during construction or 

renovation works. 

The detector covers can only be used for IQ8Quad fire detectors with built-in alarm sounder! 

Application only for detector types with Part Nos: 802283, 802384, 802386 and 802385. 

50 pcs 

Base cover for IQ8Quad 

The cover plate protects the IQ8Quad detector base against contamination during construction 

or renovation works. 

50 pcs


805571 

805574 

805576 

¬qXh£− 

¬qXk#− 

¬qXm)− 

Flush mount kit for base IQ8Quad 

Adapter for installation in ceilings and for mounting the detector bases IQ8Quad (Part Nos. 

805590 and 805591) to the bottom side of false ceilings. 





Material ABS, plastic 


Weight approx. 165 g (with surface ring) 

Dimensions (ØxD) 175 x 60 mm 

Ceiling opening Ø min. 140 mm 

Height Visible height of the detector in the 

built-in conditions: 45 mm 

4inch trim ring and snap-in mounting clips for IQ8Quad detector base 

Snap-in mounting clips and trim ring for base installation, e.g. for installation on 4” electrical 

boxes. 


Dimensions outside diameter = 155mm, 

inside diameter = 117mm, H = 19mm 



1 x trim ring and 2 x snap-in mounting clips 


Label plate for detector base IQ8Quad 

Before or after the installation of the detector, the label plate can be inserted at the side slot 

of the IQ8Quad detector base. 

For identification purposes the detector can be provided with the detector address and detector 

zone for ceilings with a maximum height of 3m. 

A label can be attached to the inscription field. Blank labels can be marked when using a PC, 

e.g. SIGEL Part No. LP725-white (58 x 18 mm) or other suppliers of writing materials or other 

suppliers of writing materials. 

There is a help file in the download area for creating the printing material. 

Applicable for Base 805590/91 with 805570; for 805593, 805594. 

Not to be used for Base 805590/91 in combination with 805571, 805572, 805573, 805574. 

10 pcs 


125 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

126 


805577 

805570 

805573 


¬qXn,− 

¬qXg~− 

¬qXj©− 

Mounting adapter for intermediate ceilings 

The mounting adapter is used for the quick and secure attachment of bases of the IQ8Quad 

detector series, 9x00, IQ8Alarm & alarm signalling devices, parallel detector indicators, etc. 

to suspended ceiling systems. It saves the usage of special hollow cavity fasteners, since 

the mounting screws of the bases are screwed directly into the slots of the mounting 

adapter. The mounting adapter offers additional advantages in the fixing of the cables, 

rigid/flexible cable inlays and threaded cable connections. 

10 pieces 

Application examples for fixing of cables, rigid/flexible cable inlays and threaded cable connections 

IP 43 protection for detector base IQ8Quad, flat design 

For installation in environments with a dust and humidity. The IP protection protects the 

IQ8Quad detector base against dust and humidity. It increases the protection level to IP 43. 

For easy mounting to the base, the IP protection is provided with an adhesive film. 


Material SBR/NR 

10 pcs 

IP 43 protection for IQ8Quad detector bases, deep design 

As 805570 but as universal protection. Additionally, the seal prevents humidity from entering 

at the sides. 


Material rubber 



5 pcs


805572 

769836 

¬qXi¦− 

¬m¥Ej− 

IP 43 moisture-proof surface-mounted base adapter aP for IQ8Quad detector base 

The damp location base adapter was specifically designed for surface mount installation by 

means of cable conduits. The adapter is provided with three 20mm (diameter) cable entries. 

The built-in seal protects the adapter against condensed water. 



Material PC 

3x screw connections are included 

Dimension drawing 

Demo case for IQ8Quad detector with integrated alarm device 

Demo case with a built-in IQ8Quad detector with integrated alarm device for demonstrating 

the whole range of multisensor functionalities. 

Take note that a notebook is necessary for the startup and for the presentation. 

The power supply of the detector is provided by the notebook only via the attached USB-cable. 

Please note that this is only a demo detector. Therefore, it is not suitable for monitoring rooms 

or facilities. 

Software is available as free download on our service-homepage. 

Only one 802385 demo IQ8Quad detector O 2T/FSp with base, flush mount kit, USB cable, installation 

CD. 

127 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

128 


Accessories for Several Detector Series 

805580 


¬qXq5− 

Detector removal tool 

It is suitable for removing Series 9x00 as well as IQ8Quad detectors. Through optional adaptation 

of the suction cup in the respective insertion on the detector removal tool, the 

IQ8Quad detector covers (Part Nos. 805588 + 805589) and the base covers for IQ8Quad 

(Part No. 805587) can be attached as well as removed. The detector removal tool can be 

adapted to the telescope rod part no. 060426 and 060427 as well as with 805581 to 769813.


805581 

060427 

Features 

• Length of 1.26m in retracted state 

• 4 segments, lockable 

060426 

¬qXr8− 

¬'%

130 


805551 

Features 

• Generation of smoke, heat and CO in a single 

test unit 

• Clearing cycle of the detector via integrated 

ventilator for better reset 

• Simultaneous or sequential testing with various 

stimuli 

• Suitable for single and multi-criteria detectors 

• Suitable for smoke-, heat- and gas- (CO) detectors 

• Targeted heat rays provide fast activation of 

heat sensors (up to 90°C/194°F, and/or adjustable 

up to 100°C/212°F) 

• Test activation via infrared barrier, no mechanical 

triggering, no ceiling contact necessary 

• Easy, fast and efficient testing, as changing of 

testing device is not necessary 

• Multilingual and user-friendly menu control 

• Battery operated portable device 

• Environmentally friendly and safe through 

usage of test cartridges instead of test gas 

cans 


¬qXTE− 

Multi-stimulus detector tester 

Detector tester kit Testifire 2001 for the functional testing of point-type fire detectors with 

various sensors. The activating stimuli for smoke, heat and CO (carbon monoxide) are generated 

in this testing unit. Thus the changing of test tools for different types of detectors is 

no longer necessary. 

All fire detector types can be tested with only one test instrument. The test tool is suitable 

for all optical smoke detectors, ionization detectors, CO detectors and heat detectors. It facilitates 

fast and effective testing of single and intelligent multi-sensor detectors. So testing 

of the different sensors can be carried out one after another or for all at the same time. 

The required stimuli are generated on demand at the time of test from the corresponding 

capsule (smoke or CO). Pressurized gas cans are no longer being used. 

The selection of the testing stimuli, as well as their combination and sequence are menu 

driven via keypad and are represented on the display (multilingual). So e.g. simultaneous or 

sequential testing, or also a combination thereof, can be easily programmed and then carried 

out at the detector. The activation of the testing device occurs automatically, as soon as 

the detector interrupts the light barrier integrated in the device. If necessary, a clearing 

phase can be chosen between the respective testing criteria that enables the stimuli to be 

blown out of the detector immediately for the next test by the integrated ventilator. 

The respectively active criterion is represented by a multi-coloured LED indicator and is clearly 

recognizable even from large distances. The fill-level of the respective test resources 

capsules can be shown in the display. Warnings are indicated automatically e.g. if a capsule 

is nearly empty. The capsules offer a much higher test capacities in comparison with aerosol 

cans. 

The power supply of the testing head occurs via Ni-MH batteries (metal hydride batteries) 

in the adapter between testing head and telescopic rod. Charging of the battery occurs with 

the charger optionally via adapter (100-230 V AC) or via 12 V DC input (vehicle cigarette 

lighter). 

Suitable for IQ8Quad and 9x00 detector series. 


Heat detector response threshold up to 90°C adjustable up to 100°C 



Relative humidity max. 90 % (without formation of condensation) 

Battery charging time 75-90 minutes 

Detector tester kit Testifire 2001 consist of: 

Testing head, smoke capsule, CO capsule, 2 Ni-MH battery packs, charger 

Selection of different test criteria displayed 

Accessories: 

805552 Smoke capsule for Multi-stimulus detector tester 805551 (Testifire TS3) 

805553 CO capsule for Multi-stimulus detector tester 805551 (Testifire TC3) 

060426 Plastic telescopic extension 

060427 Plastic telescopic rod 

060431 Spare battery baton


805552 

Features 

• Non-flammable, non toxis materials 

• Production of test gas only during the testing 

• Does not cause any residue in the sensor 

chamber 

• Suitable for optical and ionization detectors 

• No test gas storage under pressure – no dangerous 

good 

• More productivity than the spray can 

805553 

Features 

• Non-flammable CO activating-material 

• Generation of small amounts of CO 

• Generation of CO during testing only 

• No storing of pressurized CO - no dangerous 

good 

• More productivity than the spray can 

805582 

¬qXUH− 

¬qXVK− 

¬qXs;− 

Smoke capsule for Multi-stimulus detector tester 805551 

Replacement smoke capsule (Testifire TS3) for the testing of smoke detectors series 

IQ8Quad and 9x00 with optical and/or ionisation sensors. Suitable for the multi-stimulus 

detector tester 805551. 

CO capsule for Multi-stimulus detector tester 805551 

Replacement CO capsule (Testifire TC3) for the testing of detectors with carbon monoxide 

sensors (CO). Especially suited for the IQ8Quad OTG Multisensor Detector 802473 (with CO 

sensor). Suitable for the multi-stimulus detector tester 805551. 

The IQ8Quad OTG multisensor detector (CO) 802473 is generally tested either 

- with the test gas 060430.10, suitable for the smoke detector tester 805582, or 

- with 805552, suitable for the muli-stimulus detector tester 805551. 

The 802473 is VdS-approved as a smoke detector, the CO test gas is required for the additional 

triggering of the electrochemical CO gas cell. 

Smoke detector tester 

The smoke detector tester is designed for electric function control for the IQ8Quad and 

Series9x00 detectors. After an aerosol has been released, the operation capacity of the measuring 

chamber can be tested by using the transceiver. The smoke detector tester is adapted 

to the rod (Part No. 060427). 

The telescopic rod is not supplied as standard. 

Accessories: 

060426 Plasitc telescopic extension 


131 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

132 


060430.10 

805583 

805586 

Features 


¬'%?§/21f− 

¬qXt>− 

¬qXwG− 

• Exterior lid with Velcro fastening transportation 

straps for telescopic rod and extensions 

• Inside lid with 2 storage compartments for battery 

backs 060431 

• Inside compartment with up to three optional 

dividers 

• Big front pocket, with up to two optional dividers 

• Wide shoulder strap with sliding shoulder pad 

and additional handles 

• Cover with carrying strap for up to 4 telescopic 

rods 060427 and/or extensions 060426 

Test gas for smoke detecetor tester 805582 

For IQ8Quad and series 9x00 detectors, suitable for smoke detector tester 805582. 


Content 250ml per bottle 

Not suitable for Series 9000, 9100 and 9200 ionisation smoke detectors. 

Please take note that this item has to be handled as dangerous good (aerosols, non-flammable, 

UN1950) 

CO test gas for smoke detector tester 805582 

Test gas for testing carbon monoxide CO-detectors. Specifically designed for the OTG multisensor 

(CO) IQ8Quad 802473, suitable for smoke detector tester 805582. 


Content 250ml per bottle 

The OTG multisensor detector (CO) IQ8Quad (Part No. 802473) should only be tested in connection 

with test gas 060430.10 suitable for smoke detector tester 805582. Detector 802473 

has been approved as smoke detector by VdS and the CO test gas is used to additionally trigger 

the electrochemical CO-gas cell. 

Please take note that this item has to be handled as dangerous good (aerosols, non-flammable, 

UN1950) 

Carrying bag for test equipment including cover for telescopic rods 

The carrying bag has many pockets and compartments in which the ESSER smoke alarm 

testers, test gas bottles, all cables and other maintenance accessories can be stored. So 

everything you need for maintenance can always be found in one place. The upholstered, 

adjustable shoulder strap ensures a very easy and comfortable transport. An additional 

advantage: The bag protects equipment from dirt and moisture. 


Dimensions (W x H x D) 480 x 420 x 260 mm (carrying bag) 

1 x carrying bag and 1 x cover for telescopic rods/ extensions


060429 

Features 

• Mains cable is not required for testing 

• Power supply with rechargeable NiMH battery 

in the adapter of the telescopic rod 

• Time based termination of testing after 120 

seconds in order to prevent any heat related 

damages of the detectors 

• Detector head is switched off after not being 

used for 5 minutes 

• Adjustable inclination angle of detector head 

for an optimal orientation towards the object 

which has to be tested 

• Testing height up to 6 metres with telescopic 

rod and up to 9 metres with its extension 

device 

• Excess-current protection for the battery 

• Display of operating status of the detector head 

with Duo-LED (red/green) 

• Battery can be charged via mains supply or via 

cigarette lighter in vehicles 

060431 

769870.20 

¬'%>!− 

¬'%@'− 

¬m¥g§/31J− 

Test head for heat detector together with battery and charger 

Device for testing mounted fixed temperature, rate-of-rise and combination detectors when 

already installed. Response level of up to 90°C. Power supply of test head occurs via NiMH 

battery in the adapter between test head and telescopic rod. Can be used for detector series 

S-3000, 9x00 and IQ8Quad. The battery is recharged either with the charger or via mains 

supply (115V AC/230V AC) or via 12V DC cigarette lighters in vehicles. 




Relative humidity max. 85% (non-condensing) 

Battery charging time 75-90 mins. (if completely discharged) 

Batteryr life-time at least 500 charge/discharge cycles 

Test head, 2 battery batons, charger 

Accessories: 

060426 Telescopic extension 


060431 Spare battery baton 

Spare battery baton 

Replacement battery pack (NiMH) for Test Head 060429 and 805551. 

Smoke detector tester 

Smoke detector tester allows fast and reliable functionality testing for Series IQ8Quad and 

9x00 smoke detectors. Through reduced mechanically controlled actuation pressure, 

suspended installed detectors can also be tested. Control electronics guarantee a defined 

spray impulse. Spray can and batteries can be easily replaced. 


Operating voltage 2 x 9V batteries 

Testing capacity approx. 2000 applications / can 

Telescopic rod 769813 is required. 

Substitute for 769870.10! 

1 x test gas 769070 

2 x9V batteries 018051 

1 x bellow for IQ8Quad and 9x00 

Accessories: 

769070 Test gas 

018051 9V battery 

133 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

134 


769871.20 

769070 

769813 

769814 


¬m¥h§/31M− 

¬m{gY− 

¬m¥.%− 

¬m¥/(− 

Conversion kit for smoke detector tester 769870 

The conversion kit (Part No. 769871.20) is used to convert the smoke detector tester (Part 

No. 769870 and 769870.10) to test the functions of IQ8Quad and 9x00 smoke detectors. 

The conversion kit includes special contact fields to test smoke detectors and the associated 

expansion bellows. 

Substitute for 769871! 

1 x bellow for Series IQ8Quad and Series 9X00 

1 x contact spring 

3 x fixing screws 

Test gas for smoke detector testers 769870.10 and 769870 

For series 9x00 and IQ8Quad detectors. 


Content 150 ml 

CFC-free test gas, suitable for approx. 2000 applications. 

Please take note that this item has to be handled as dangerous good (aerosols, flammable, 

UN1950). 

Telescopic rod 

For smoke detector tester 769870.20 (length 3.75 m, three pieces, locking devices). 


Length 3.75m, three parts, lockable 

Extension pole 

For smoke detector tester 769870.20, detector removal tool 769804 and telescopic rod 

769813 (length 4m, two pieces, locking devices). 


Length 4m, two parts, lockable


781482 

769080 

Features 

• 40 sec. burning-time per smoke pellet 

• 18 m 3 smoke produced per smoke pellet 

¬o/sN− 

¬m{qw− 

Kit for suspended installation 

Kit for detector bases 781590, 805590, 805591 and 801593 for suspended installation with 

pendulum stabiliser, cable entry at the top, pull relief by means of PG cable entry including 

junction box with terminals. The detector height can be adjusted individually depending on 

the cable length to bridge over the heat cushion below the ceiling.. 


Installation attached to the zone cable 



Dimensions Aluminium-Stabiliser Ø = 84mm, h = 15mm 

Assembly Cable entry PG7 

It is not possible to use telescopic rods. 

Not suitable for Series 3000. 

as shown 

Smoke pellets for testing purposes 

Pellets for the generation of dense bright smoke. The pellets are lit with an open flame (e.g. 

matches, lighter etc.). Extinguishing is not necessary. Please ensure the use of a non-flammable 

base. After ignition the pellet will burn to complete ash (without formation of flames). 

Without oil 

6 pcs. 

135 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

136 


781550 


¬o0SW− 

Protective cage 


Material steel with paint coating 


Dimensions (Ø xH) approx. 140 x 115mm 

Can be used with all bases, also for wireless base and wireless gateway. 

Application example with IQ8Wireless detector base and IQ8Alarm

Manual Call Points Large Design - ABS 138 - 141 

Large Design - Aluminium 142 - 143 

Large Design - Accessories 144 - 147 

Small design - ABS 148 - 153 

Special Design 154 - 156 

137 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

138 

Manual Call Points Large Design - ABS 

Features 

• Slimline design 

• Plug-in connection clamps 

• Optional terminal clamps 

• 2 x cable entries on top, at the bottom and on the 

rear panel 

• Fixing on standard fm installation box 

• Test function via manual call point service key 

• Detectors that are not ready for operation can be 

marked with the “Out of Order” label by reversing 

the enclosed operating front foil 

Electronic Modules 

Pictogram according to EN 54-11 


The advanced generation of manual call points with fragile element meets the latest multicultural 

requirements of the EN 54 - 11 standards as type B (double action). The elegant 

detector housing, available in 5 different RAL colours, is provided with a pictogram, which 

is easy to comprehend for foreign people, illiterates as well as children. 

Depending on individual requirements, optional labelling foils can be used which can easily 

replace the pictogram without special tools. The triggering element is protected by a pane 

of glass and is indicated by arrows. 

If required, optional labelling foils can be used, which can easily replace the pictogram. The 

triggering element is protected by a glass pane and is indicated by arrows. The innovative 

manual call points can be tested by using the service key to activate the triggering mechanism, 

which is hidden by a faceplate. Clever design structures allow easy installation. 

Type B definition - double action in accordance with EN 54-11 § 3.4.2 

(excerpt taken from EN standard): 

Manual fire alarm unit, for which the alarm status cannot be set until an alarm is additionally 

triggered by the user after the fragile element has been broken or its position has been 

changed. 

Take note, for a LARGE MCP you have to order the electronic module and the MCP housing separately 

to have a complete MCP. 


Not all possible combinations of electronic modules and housings are approved by VdS. When 

using the manual call point as a fire detector for manual actuation in compliance with the EN 

54-11 standards, a red housing together with the provided pictogram must be used. When 

using the manual call point in heat exhaust or extinguishing system areas, the appropriate housing 

colour must be chosen in compliance with the correct standards. 

Wago clamps for looping in wires, e.g. type 273-100 (0.5mm 2 -1.5mm 2) or 

273-104 (0.75mm 2 - 2.5mm 2) can be mounted on the detector base.


Standard 

804900 

804901 

804902 

¬qR!n− 

¬qR"q− 

¬qR#t− 

Conventional MCP electronic module 

Approval: 


VdS, CNBOP 

With alarm indicator, suitable for connection to a standard detector zone. 




Alarm display LED, red 

No. of detector/zone 10 detectors per zone (according to VdS) 

Connection terminal max. 2.5 mm (AWG 26-14) 



Type of protection IP 44 (in housing), IP 55 (with accessory) 

Housing PC ASA plastic 

Weight approx. 236g with housing 


Detector specification EN 54-11, type B 

In combination with the yellow housing (Part No. 704902), the electronic module is approved 

as an electronic control unit for gas extinguishing systems. 

The 804900 electronic module with yellow housing conforms to the EN 12094-3 standard and 

can be used as electronic control unit for gas extinguishing systems in dry, non-hazardous 

industrial premises. 

Conventional MCP electronic module with second microswitch 

Approval: 

VdS, CNBOP 

As 804900 but with second microswitch. 


Switching contact second microswitch contact load 30V DC / 1A 

In combination with the yellow housing (Part No. 704902), the electronic module is approved 

as an electronic control unit for gas extinguishing systems. 

The 804901 electronic module with yellow housing conforms to the EN 12094-3 standard and 

can be used as electronic control unit for gas extinguishing systems in dry, non-hazardous 

industrial premises. 

Conventional MCP electronic module w/o snap-on function 

Approval: 

VdS with blue housing 704901 

As in 804900 but without snap-on function. 

This electonic module is only approved as an electric stop push-button for gas extinguishing 

systems only when combined with the blue housing (Part No. 704901). The electronic module 

804902 with blue housing complies with the EN 12094-3 standard and therefore it can be used 

as an electric stop push-button for gas extinguishing systems in dry, non-hazardous branches. 

In case the manual call point is used as a “House Alarm” push-button, pre-printed labels are 

provided in the manual call point package. 

139 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

140 


IQ8MCP 

804905 

804906 


¬qR&}− 

¬qR'¢− 

IQ8MCP electronic module 

Approval: 




Alarm current w/o communication curtain optic typ. 18 mA 


Operating modus LED, green 

No. of detector/zone 10 detectors per zone, 127 detectors/loop 

(according to VdS) 

Connection terminal max. 2.5 mm2 (AWG 26-14) 



Type of protection IP 44 (in housing), IP 55 (with accessory) 


Weight approx. 236 g with housing 


Detector specification pr EN 54-11, type B 

IQ8MCP electronic module w/o isolator but with relay 

Approval: 


VdS, CNBOP 

Addressable electronic module suitable for use in the esserbus and powered loop with alarm 

latch and alarm indicator. Optional connection for conventional MCP. Without BUS connection, 

the detector operates as conventional MCP. Built-in loop isolator in the manual call 

point. 

VdS 

As 804905 but with relay, without loop isolator and without connection for standard manual 

call point. 

The relay output is activated with the triggering of this detector. The relay output can be programmed 

in the System 8000 and IQ8Control fire alarm control panel customer data as a 

control group. 

Relays contact load 30V DC / 1A


Plastic housing - large design 

704900 

704901 

704902 

704903 

704904 


¬gR!d− 

¬gR"g− 

¬gR#j− 

¬gR$m− 

¬gR%p− 

Housing for electronic module 80490x. 


Installation surface mount 



Weight approx. 83g (w/o electronic module) 

Dimensions (W x H x D) 133 X 133 X 36mm 

Housing with glass pane (704910) 

Plastic key (769910) 

Accessories: 

704910 Spare glass for manual call points 

769910 Plastic spare key 

769911 Metal key for large MCP 

769916 Service key 

704917 Option IP55 shrink sleeve for large MCP 80490x 

704911 Universal foil for large MCP housing ABS 

Housing with glass pane, red, similar to RAL 3020 

The red manual call point housing is only available with the pictogram (as shown) in compliance 

with EN 54-11. 

Please note that in compliance with EN54-11 the labelling must come with the burning house 

symbol. 

Housing with glass pane, blue, similar to RAL 5015 

The 804902 electronic module in a blue housing complies with the EN 12094-3 and thus can be 

applied as electronic stop button for gas extinguishing systems in dry, non-hazardous production 

sites. 

For different use such as application as “HOUSE ALARM” push button, ready-made labels are 

provided. 

Labelling foil set (white) for various international applications. 

Housing with glass pane, yellow, similar to RAL 1021 

The 804900 or 804901 electronic module in a yellow housing 704902 complies with the EN 

12094-3 and thus can be applied as electronic control module for gas extinguishing systems in 

dry, non-hazardous production sites. 

For different use such as application as “HOUSE ALARM” push button, ready-made labels are 

available. 

Labelling foil set (black) for various international applications. 

Housing with glass pane, orange, similar to RAL 2011 

Labelling foil set (black) for various international applications. 

Housing with glass pane, green, similar to RAL 6002 

Labelling foil set (white) for various international applications. 

141 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

142 

Manual Call Points Large Design - Aluminium 

Electronic Modules 

Electronic Module Series 9000 

704477.10 


¬gMn§/21N− 

Both housing and electronic module need to be ordered. Not all possible combinations of electronic 

modules and housings are approved by VdS. The approved combinations are listed in the 

VdS approval field for the corresponding electronic module. 

For connection to a conventional detection zone, with alarm indicator. 


Operating voltage 8 to 30V DC 

Switching contact second microswitch contact load 30V DC / 1A (only 804901) 


Alarm current @ 9 V DC typ 9 mA 



Connection terminal 0.6 mm to 1.5 mm 2 



Type of protection IP 43 (with die-cast aluminium housing) 

IP 54 (with die-cast aluminium housing and 

option 704070) 

Weight approx. 100 g w/o housing 



MCP-electronic module Series 9000 with second micro-switch 

Approval: 

Electronic Module Series 9200 

804473.10 

¬qMj§/21L− 

VdS with housing 704801.10 

printed with pictograms in accordance with EN 54-11 

To be used on esserbus and powered loop, with soft address coding, alarm latch and alarm 

indicator. Conventional detectors can be connected to input of the module. Without BUS 

communication, the detector operates like standard detectors. 




Emergency operation alarm typ. 18 mA 


No. of detector/zone 10 / zone, 127 / loop (VdS) 

Connection lead 0.6 mm to 1.5 mm 2 



Type of protection IP 43 (complete with aluminium housing) 

IP 54 (complete with aluminium housing and 

module 704070) 

Weight approx. 100 g without housing 



MCP-electronic module Series 9200 with zone isolator 

Approval: 

VdS with housing 704801.10 

printed with pictograms in accordance with EN 54-11

Manual Call Points Large Design - Aluminium 

Aluminium die-cast housings 

704801.10 

¬gQ"§/21@− 


Installation surface mount 

Type of protection IP 43, IP 54 with kit 704070 

Material aluminium, die-cast 



red = similar to RAL 3000; blue = similar to RAL 5009; yellow = similar to RAL 1018 

Key: 769910, 769911 (Accessory) 

Housing with glass pane and plastic key, fixing material, 1 x multilingual “Out of Order” paper 

insert, 2 x cable entries, 2 x dummy plugs 

Housing with glass, red , in compliance with EN 54-11 

printed with pictograms in accordance with EN54-11 

MCP - housing neutral Version / without printed pictogramm 

704800 

704850 

704870 

704890 

¬gQ!b− 

¬gQS*− 

¬gQgf− 

¬gQ{;− 

MCP - Housing German Version 

704804 

704854 

704874 


¬gQ%n− 

¬gQW6− 

¬gQkr− 

MCP-housing aluminium red, neutral 

MCP-housing aluminium blue, neutral 

MCP-housing aluminium yellow, neutral 

MCP-housing aluminium grey, neutral 

MCP-housing with glass, red, printed: Hausalarm - ESSER 

MCP-housing with glass, blue, printed with “Hausalarm-ESSER” 

MCP housing with glass, printed: Hausalarm - ESSER 

143 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

144 

Manual Call Points Large Design - Accessories 

704910 

701040 

769921 

704917 

704911 


¬gR+¤− Spare glass pane for MCP-housings 70490x, 7048xx und 761694 

¬g+I'− 

Spare glass pane for detector housings large design 70490x, 7048xx, 761694 and 761697 

in compliance with EN 54-11. 


Glass thickness 0.9mm 

Dimensions (WxH) 80 x 80mm 

10 pcs 

Spare glass pane red for MCP-housings 7047xx und 7048xx 

Spare glass pane, printed with red circle segments (similar to RAL 3000) for all 7047xx and 

7048xx manual call points (large design). 


Glass thickness 0.9mm 


10 multilingual “Out Of Order” paper labels are included. 

10 pcs 

¬m¦6?− “Out of order” sign - Multilingual for large MCP 

¬gR20− 

Plastic sign for all 7047xx, 7048xx and 70490x manual call points (large design). 



Option IP55 shrink sleeve for large MCP 80490x 

10 shrink sleeves for clamp terminals to increase protection class to IP55. 

seal included 

10 pcs 

¬gR,§− Foil for front face w. universal text for large MCP ABS 70490x 

Universal, punched foil set (transparent with white imprint) for the labelling field, different 

from the standard version. 

Transparent foil with white lettering. 

10 pcs


704912 

704070 

769910 

769911 

769916 

¬gR-!− Foil for front face w. universal text for large MCP ABS, black lettering 

¬gIgV− 

As 704911 but with black imprint. 

10 pcs 

IP 54 kit for large manual call points 7048xx 

Cable entries to increase protection class from IP 43 to IP 54 for manual call points in diecast 

aluminium housings (7048xx). 


Cable diameter 6 mm 


Material PS 

as shown 

¬m¦+§− Plastic key for large MCP 

Plastic key type D for all manual call points (large design). 

Please note that for activating the test functionality of electronic modules (Part No. 80490x), the 

service key 769916 is required. 

¬m¦,!− Metal key for large MCP 

Metal key type D for all detector housings (large design). 

Please note that for activating the test functionality of electronic modules (Part No. 8049xx), the 

service key 769916 is required. 

¬m¦10− Service key for electronic module (Part No. 80490x) 

With this metal service key, the test functionality of the manual call point is activated and 

reset by authorised persons only. 

The key is suitable for all electronic modules with part nos. 80490x from index 05 and 

yellow locking. 

145 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

146 


781682 

781692 

781693 

781694 

781695 

781696 


¬o1sR− 

¬o1}p− 

¬o1~s− 

Weather protective cover, red for MCP-housings 7047/48xx 

Protective housing with protruding roof edge, for all 7047xx and 7048xx detector housing 

for increased mechanical protection as well as for protection from bad weather conditions. 


Material PVC 



Weather protective cover and mounting material 

Weather protective cover, blue for MCP-housings 7047/48xx 

Protective cover similar to 781682. 



Weather protective cover and mounting material 

Protective cover for manual call points Esser, German 





This protective cover prevents false alarms, without hampering real alarms. This device consists 

of a rack and a lid, made of transparent polycarbonate. 

It prevents inadvertent activation, vandalism, dust and water from triggering false alarms. The 

protective cover is suitable for all manual call points. 

Accessory for installation 


¬o1¡v− Protective cover for manual call points - Esser, English 

As 781693, but Esser-English 

¬o1¢y− Protective cover for manual call points - Esser, French 

¬o1£|− Protective cover for manual call points - Esser, Italian


781697 

781698 

781699 

¬o1¤¡− Protective cover for manual call points - Esser, Spanish 

¬o1¥¤− 

Surface spacer for protective cover 

The spacer is required for surface mount wiring. 




Accessory for installation 

¬o1¦§− IP55 kit for protective cover 

Mounting kit - self-adhesive sealing kit for protective cover (781693) and an increased protection 

level from IP 44 to IP 55. 


147 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

148 

Manual Call Points Small design - ABS 

Features 

• Slimline design 

• Plug-in connection terminals (two direction) 

• Optional terminal terminals 

• Triple key function (test, open, reset) 

Complete MCP 

804970 

804970.VC0 


¬qRgr− 

¬qRg§/WD1-− 

The new generation of manual call points meets the latest multicultural requirements of the 

EN 54 - 11 standards as type A (Single Action). The elegant housing is provided with a pictogram, 

which can be understood by children as well as in an international context. 

Depending on individual requirements, the pictogram can be easily replaced by optional 

labelling field foils without using additional tools for removal. The actuation field is marked 

by arrows pointing towards it. The innovative manual call points can be tested by using the 

key to activate the triggering mechanism, which is hidden by a faceplate. Smart housing and 

terminal design enables easy installation. 

When replacing the glass pane by the optionally available plastic pane with resettable function 

the MCP can be reset from the outside with the key! 

For the surface mounting of the MCP the surface mount base 704980 is to be ordered separately, 

if the cable wasn’t layed about a standard flush mount wall socket. 

Type a definition - single action in accordance with EN 54-11 § 3.4.1 

(excerpt taken from EN standard): 

Manual fire alarm unit, for which the alarm status is automatically set (additional alarm triggering 

is not required) after the fragile element has been broken or its position has been changed. 

Snap-on positions / connection terminal 

Conventional MCP, red housing with glass pane - Esser 

Approval: 

Including housing and alarm indicator. For connection to a conventional detection zone. 


VdS, CNBOP 



Alarm display red LED and yellow actuation indicator 


Connection terminal max. 2.5 mm 2 (AWG 26-14) 



Type of protection IP 43, IP 55 with cover 704965 





88 x 88 x 57 mm with surface mount housing 

Detector specification EN 54-11, type A 

1 x glass pane 704960 

1 x key 704966 

1 x multilingual paper labels with “Out of order” pictogram. 

Conventional MCP, red housing with glass pane - Esser, China 

As 804970 but - Esser, China


804971 

804973 

804973.F0 

¬qRhu− 

¬qRj{− 

¬qRj§/G1m− 

IQ8 MCP, red housing with glass pane - Esser 

Approval: 


VdS, CNBOP 

Suitable for esserbus and powered loop connection, with soft address coding, alarm latch 

and alarm indicator. Conventional detectors can be connected to input of the MCP. Without 

BUS communication, the detector operates as conventional MCP. Detector housing is 

included. 



Alarm current w/o communication curtain typ. 18 mA 

Alarm display red LED and yellow actuation indicator 

Operating modus green LED 

No. of detector/zone max. 127 detectors per loop (according to VdS) 




Type of protection IP 43, IP 55 with cover 704965 





88 x 88 x 57 mm with surface mount housing 



1 x key 704966 

1 x multilingual paper labels with “Out of order” pictogram 

IQ8 MCP, red housing with plastic pane - Esser 

Approval: 

VdS 

As 804971 but with plastic triggering element, which supports easy reset after an alarm has 

been triggered without having to replace the broken element (glass pane). 

Typically applied in clean rooms as for example in food processing industries. 

see application example in Part No. 704964 

1x plastic operating panel 704964 

1x key 704966 

1x multilingual paper insert with “Out of Order” pictogram included 

IQ8 MCP compact, red housing with plastic pane, French 

as 804973, but French version 

see application example in Part No. 704964 

149 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

150 


Electronic module - small design 

804955 

804950 


¬qRXE− 

¬qRS6− 

IQ8MCP electronic module with glass - Esser 

Approval: 

As 804971 but without housing. 


VdS 


Quiescent current @ 19 V DC approx 45 μA 

Alarm current w/o communication curtain typ. 18 mA 

Alarm display LED, red and yellow flag 

Start LED, green 

No. of detector/zone max. 127 detectors per loop (as per VdS) 




Type of protection IP 43 (in Housing), IP 55 with cover 704965 


Dimensions (W x H x D) 88 x 88x 21 mm 


1 x spare glass pane 704960 

1 x multilingual paper labels with “Out of order” pictogram 

Conventional MCP electronic module with glass - Esser 

Approval: 

With alarm indicator, for the connection to a standard detector zone. 


VdS 




Alarm display LED, red and yellow flag 

No. of detector/zone max. 10 detectors per loop (as per VdS) 

Connection terminal max. 2,5 mm 2 (AWG 26-14) 



Type of protection IP 43 (in Housing), IP 55 with cover 704965 



Dimensions 88 x 88 x 57 mm with surface mounted housing 

Detector specification EN 54-11, Typ A 

1 x spare glass pane 704960 

1 x multilingual paper labels with “Out of order” pictogram


Plastic housing - small design 

704951 

¬gRT/− 

Small Design - Accessories 

704960 

704975 

704964 

¬gR]J− 

¬gRlw− 

¬gRaV− 

Housing for small MCP, blue 

Housing for electronic modules 80495x 


Installation aP 

Type of protection IP 43, IP 55 with 704965 

Housing PC ASA plastic housing 




includes 1x key 704966 and 1 piece universal labelling foil 704961 

Spare glass pane for small MCP, EN54 - Esser 

Spare glass pane with white sticked on foil and printed pictogram in compliance with EN 54- 

11 (type A). Suitable for small MCP’s. 


Dimensions (W x H) 56 x 49,5 mm 

Thickness 1,85 mm 

10 pcs 

Spare glass pane for small MCP, EN54 - neutral 

Spare glass pane with white stick on foil and printed with pictogram according to EN 54-11 

(type A), for small manual call points, without logo. 


Dimensions (W x H) 56 x 49,5 mm 

Thickness 1,85 mm 

10 pieces 

Plastic pane - resettable function, for small MCP - Esser 

Resettable, white, for small manual call points. Typically applied, for instance, in food processing 

industries or in clean rooms. 

10 pcs 


151 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

152 


704961 

704965 

704966 


¬gR^M− 

¬gRbY− 

¬gRc\− 

Foil for front face w. universal text for small MCP, white lettering 

Universal, punched foil set (transparent with white imprint) for the labelling field, different 

from the standard pictogram. 

Transparent foil with white lettering! 

10 units 

MCP Cover for small housing, transparent 

Transparent, suitable for small MCP’s. The cover serves as a protection to prevent inadvertent 

activation. 



Application example: Manual call point with mounted cover 

Plastic spare key for small MCP 

Plastic key, red, suitable for small manual alarm units. 

10 pcs


704967 

704980 

704981 

¬gRd_− 

¬gRq¨− 

¬gRr"− 

Mounting frame for small MCP, red and white 

The mounting frame is useful for mounting MCP’s on different international flush mount 

boxes. 


Dimensions (W x H x D) approx. 132 x 132 x 8mm 

Colour red (similar to RAL 3020) 

2 x fastening screws are included (red and white) 

Application example: Mounting frame with small MCP 

Surface mount housing for small MCP, red 

Red, for manual call points 804970, 804971 and 804973, for small design Electronic 

Modules 804950/61, 804955/56. With integrated support for shielding. 

The surface mount housing serves as cable entry for surface mount cabling. 




mounting material 

Surface mount housing for small MCP, blue 

Blue, for small design Electronic Modules 804950/61, 804955/56 with Housing 704951. 

With integrated support for shielding. 

The surface mount housing serves as cable entry for surface mount cabling. 



Colour blue (similar to RAL 5015) 

mounting material 

153 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

154 

Manual Call Points Special Design 

761630 

772180 


¬m1?¤− 

LF-manual activation point low frequency 

Manual activation point designed according to EN54-11 type B (double action) for manually 

triggering of hazard alarms in dry rooms. The device offers low-frequency data transmission 

over long distances of up to 20km for monitoring passive third-party detectors and 

activation via terminal card 772180. 



Alarm display LED red 


Connection terminal 0.6mm to 1.5mm2 Ambient temperature -30°C to +70 °C 

Storage temperature -35 °C to +75°C 

Type of protection IP 43, IP 54 with kit 704070 

Housing aluminium die-cast 




Contact load microswitch: max. 30 V DC / 1A 

To operate the 761630, terminal card 772180 is required. 

This LF Manual Call Point must not be operated as a fire alarm detector for fire alarm systems 

in accordance to the standard EN54-11. It is suitable only for operation in Hazard alarm 

systems as release device! 


1 x plastic key 769910 

1 x fixing material 

1 x “Out of Order” sign 

2 x cable entries 

2 x dummy plugs 

Accessories: 

704910 spare glass pane, no imprint 

¬n6qU− Terminal card for LF-manual call point 761630 

Terminal card for LF-manual call point 761630, with indicators for alarm (red), wire break 

(yellow) and short circuit (yellow). Suitable for mounting on standard mounting rails. 



Quiescent current 5 mA 


Alarm display LED red 

Fault display LED yellow 


Ambient temperature 0°C to +50 °C 




Colour grey 




761694 

¬m1¡t− 

Manual call point Series 9200, IP66 

Type B acc. to EN54-11 with loop isolator for manually triggering fire alarms or hazard 

alarms. For out-door application or application in damp environments. 


Operating voltage 8V to 42 V DC 

Quiescent current approx. 45μA 


No. of detector/zone max. 10 (according to VdS), 127 / loop 

Connection terminal max. 1,5 mm2 Ambient temperature -20 °C to +70 °C 



Housing PC-plastic 


Weight approx. 0,475 kg 


Please take note, our Part No. 769910 and 769911 can be used as spare keys. 

Substitute for 761695. 

1 x glass 704910 

1 x key and “Out of Order” sign respectively “Außer Betrieb” 

Accessories: 

704910 Spare glass for MCP 

769910 Plastic key for large MCP 

769911 Metal key for large MCP 

155 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

156 


Manual call point for hazardous areas 

761697 


¬m1¤}− 

Ex manual call point (conventional) IP66 

Approval: 

Manual call point (conventional) in conformity with EN 54-11 Type B for the manual actuation 

of a fire alarm and/or a hazard alarm, as a detector for usage in explosion-hazardous 

areas both inside and outside. 

The operating front foil has been designed as a double-sided insert. Complementary to the 

symbolism conforming to the standards for manual call points in compliance with EN 54- 

11 (Type B), it has a symbol and multilingual text on the back for the ‘out of order’ status of 

the detector and is always available for possible maintenance work. 

The labelling foil of the manual call point also has a double-sided design. In compliance with 

EN 54-11, they contain the standard symbol of a burning house. On the back, the symbol is 

supplemented with the word “FIRE” (multilingual). 




Wiring 1 kOhm / 10 kOhm internal 

No. of detector/zone max. 10 detectors per Zone (according to VdS) 

Connection terminal 0,6 mm to 4 mm 2 

Ambient temperature (T6) -55 °C bis +65 °C 

(T5) -55 °C bis +85 °C 



Housing Glass fiber reinforced polyester resin 



Detector specification DIN 14678 Form K 

Category II 2G 

Explosion protection Ex e d mb IIC T6, T5 


Substitute for 761696. 

VdS, PTB 97 ATEX 3197 

Please note, an allen key (size 4) is needed for opening and resetting the MCP, and is not 

included in the scope of delivery. 

incl. 1x glass pane 704910, 1x kit of double-sided operating front foil (with “Out of Order” on 

the back), 1x kit of double-sided labelling foil (multilingual) 

Operating front foils and labelling foils 

Accessories: 

704910 Spare glass pane for MCP-housings

Transponders esserbus 158 - 170 

157 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

158 

Transponders esserbus 

808610.10 


¬qw+§/21J− 

esserbus transponder 12 relays (8bit) 

Approval: 


The esserbus transponder works as a loop device on the multi-functional primary line. With 

the 12x relay module, it is possible to expand the number of exits per control unit. Depending 

on the control unit, It can be integrated or used with fire detectors in mixed operation. 

Max. of 32 esserbus-transponders can be connected on one loop. The esserbus-transponder 

can be optionally extended by adding the additional isolator board 788612. 

esserbus-transponder voltage supply: via the multi-functional primary line. The esserbustransponder 

can be wired with an external switching voltage of 12V DC or 24V DC for the 

K1 to K12 relays. The external voltage supply of the transponder can be programmed to be 

monitored in the customer data in the operating mode. In the “floating” operating mode, no 

external switching voltage of the relays is necessary. 11 relays are free programmable, the 

12th relay is exported as locking contact. The maximum line length from the transponder to 

the external device is up to 1000 m. 


Analog loop 


Rated current @ 19 V DC 

External voltage supply 

approx. 100 μA 

Voltage range 10 V DC to 28 V DC 

Current consumption @ 12 V DC 

Relays 

approx. 3 mA 

Contact load 30 V DC / 1 A (max. 3 A per transponder) 



Air humidity ¥ 95% rel. humidity (no condensation) 

Type of protection IP 40 (with housing) 



Accessories: 

788612 Loop isolator PCB 

788600 Surface mounting housing grey, similar to RAL 7035 

788650.10 Surface mounting housing white, similar to RAL 9003 

788601 Flush mounting housing grey, similar to RAL 7035 

788651.10 Flush mounting housing white, similar to RAL 9003


808611.10 

¬qw,§/21M− 

esserbus transponder 32 LED (8bit) 

Approval: 


The esserbus-transponder works as a loop device on the multi-functional primary line. 32 

outputs for direct LED control (e.g. indicator) are found on this esserbus-transponder 

module. There is one terminal screw per output on the switching mechanism. The outputs 

can be used for positive or negative signals (programming required). Max. of 32 esserbustransponders 

can be connected on one loop. The module can be extended by adding the 

additional isolator board 788612. esserbus-transponder voltage supply: via the multi-functional 

primary line. The esserbus-transponder requires an external switching voltage of 10 

V DC to 15 V DC. 

The external voltage supply of the transponder can be programmed to be monitored in operating 

mode. The maximum line length from the transponder to the external device is up to 

100 m. 


Analog loop 






Quiescent current @ 12 V DC 

LED output 

< 3 mA 

Length cabel crossover max. 100 m (Ri = 1 kƒ) / max. 3 m (Ri = 0ƒ) 



Air humidity ¥ 95 % rel. humidity (no condensation) 


Weight ca. 95 g 


Accessories: 


788600 Surface mounting housing grey, similar to RAL 7035 

788650.10 Surface mounting housing white, similar to RAL 9003 

788601 Flush mounting housing grey, similar to RAL 7035 

788651.10 Flush mounting housing white, similar to RAL 9003 

159 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

160 


808613.10 


¬qw.§/21S− 

esserbus transponder 4 IN / 2 OUT 

Approval: 


The esserbus transponder works as a loop device on the multifunctional loop. 

Conventional automatic detectors and manual alarm units can be connected without addressing: 

- up to 31 esserbus transponders 4 zones / 2 relays on one multifunctional primary loop 

- up to 30 conventional detectors per zone without SOC 

- up to 10 conventional detectors per zone with SOC 

- up to 10 non-automatic or technical alarm devices per zone 

The esserbus transponder needs an external switching voltage of 12 V DC or 24 V DC. The 

external voltage supply of the transponders can be programmed with supervision in operating 

mode. 


Analog loop 






Current consumption @ 12 V DC max 120 mA 

Quiescent current @ 12 V DC 

Detector zone input 

approx. 6 mA 

Rated voltage 9 V DC 

Current consumption max. 25 mA 

Length conductor cable max. 1.000 m 

Relay contact rating 30 V DC / 1 A 

Relay monitoring 10 kƒ / ±40% 



Air humidity ¥ 95% (no condensation) 




Accessories: 

788603.10 Module housing for C-mounting bar or top hat rail mounting 


788600 Housing surface mount, grey 

788650.10 Housing surface mount, white 

788601 Housing flush mount, grey 

788651.10 Housing flush mount, white


808613.20 

Features 

¬qw.§/31Y− 

• Two relays, optionally programmable with different 

operation modes 

• Programmable 2-group dependence function 

• Reset relay function programmable 

esserbus transponder 4 detector groups / 2 relays 

Approval: 

VdS 

The esserbus transponder works as a loop device on the multi-functional primary line. There 

is also a connection possibility for automatic standard detectors, manual detectors without 

addressing and special detectors. Additionally there are two floating relay outputs available 

for controlling and reset functions. 

- max. 31 esserbus transponder on a multi-functional primary line 

- max. 10 standard manual detectors or Technical Alarm Modules per group 

- max. 127 groups per loop 

- max. 31 standard detectors per detector group 

- max. 10 Technical Alarm Modules per detector group 

The external voltage supply (+Ubext = 12 V DC or 24 V DC) must always be connected. For 

standard operation (12 V DC) the voltage converter (Part No. 781336) is additionally necessary. 

The transponder’s external voltage supply can be programmed with supervision in 

operating mode. The included connector element EOL-Z (Part No. 808625) must be used for 

the standard monitoring of the detector group inputs. 

The EOL-Z has to be connect to the respective terminals in the last detectro base. 


Analog loop 







Quiescent current 


approx. 10 mA 



Length conductor cable max. 1,000 m 


Relay monitoring 10 kƒ/±40% 



Air humidity ¥ 95% rel. humidity (w/o condensation) 

Type of protection IP 40 (in the housing) 



1 x additional enclosure 

Accessories: 





788651.10 Housing flush mount, white 


781336 DC/DC converter output voltage 

808625 EOL-Z Module for detector groups 

161 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

162 


808613.30 


¬qw.§/41_− 

esserbus Transponder SST 

Approval: 

VdS 

esserbus transponder Standard interface EXTINGUISHING for connection of extinguishing 

systems to the fire detection system. 

An external switching voltage of 12 V DC or 24 V DC can be connected to the esserbus 

transponder. The voltage converter (Part No. 781336) is required for 12 V DC operation. The 

transponder’s external voltage supply can be programmed with supervision in operating 

mode. 


Analog loop 







Quiescent current 


approx. 10 mA 







Storage temperature -25°C tos +75°C 





1 x additional enclosure with 3,3k and 680 terminating resistor for SST 

Accessories: 







781336 DC/DC converter output voltage


808614.10 

808615 

¬qw/§/21V− 

¬qw0~− 

esserbus transponder 1 IN 

Approval: 



The esserbus transponder works as a lbus device on the multifunctional loop. 

Conventional automatic detectors and manual alarm units can be connected without addressing: 

- up to 31 esserbus transponders 1 zone / 2 relays on one multifunctional primary loop 

- up to 30 conventional detectors per zone without SOC 

- up to 10 conventional detectors per zone with SOC 

- up to 10 non-automatic or technical alarm devices per zone 

External power supply is required for transponder operation. Optional voltage monitoring. 

Analog loop 

Rated voltage 19 V DC, max 42 V DC 

Rated current @ 19 V DC < 120 μA 



Rated voltage 12 V DC or 24 V DC 

Current consumption max 120 mA 

Quiescent current < 3 mA 




Length cabel crossover max 1.000 m 







esserbus communication transponder 

With this esserbus transponder the extinguishing relay output 8010 can be integrated on the 

bus of panel 8000 or IQ8Control, thus enabling several extinguishing zones to be networked 

with each other. On each bus, a maximum of eight 8010 extinguishing relay outputs can be 

operated and networked. All indicators and controls can be activated from the fire alarm 

panel. The communication transponder occupies one address on the esserbus. 


Analog loop 




< 150 μA 


Rated voltage 12 V DC or 24 V DC 

Quiescent current < 3 mA 







Mounting: in the housing of the 8010 extinguishing realy output 

including loop isolator PCB (788612) 

163 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

164 


808619.10 

Features 


¬qw4§/21e− 

• Usage of Series 9200 intelligent detectors 

(such as OT, OTI, O 2T Detectors) as FSA detectors 

is possible 

• Connection of IQ8Quad O Detectors (part no. 

802371), TD Detectors (part no. 802271), OT 

Detectors (part no. 802373) and O 2T Detectors 

(part no. 802374) (DIBt-approved) as FSA 

detectors is possible 

• FSA detectors programmable as devices in the 

loop 

• Status indicator of door arrester system to the 

fire alarm control panel 

• Actuation of the locking device also via the 

automatic fire detectors in non-FSA operation 

• Stand-alone operation of the FSA transponders 

is possible 

• Usage of IQ8Quad O Detectors (part no. 

803371), TD Detectors (Part No. 803271) and 

O 2T Detectors (Part No. 803374) in stand-alone 

operation of the FSA transponders to the standard 

detector group is possible 

esserbus transponder for door release application 

Approval: 

VdS 

The transponder is suitable for usage for various applications: in stand-alone operation or 

on the esserbus. In esserbus operation, the Series 9200 automatic fire detectors and those 

of the IQ8Quad family (see feautures for types) can be used as detectors in door arrester 

systems (FSA). In FSA transponder loop operation, the door arrester system status is indicated 

on the fire alarm control panel. 

For stand-alone operation, detectors of the IQ8Quad family are supported without loop isolator 

(see features for types). 

Up to a maximum of 31 IQ8Quad detectors per detector group input can be connected 

without isolator, depending on object conditions. 

For operation, the transponder requires an external supply voltage. It is possible to monitor 

this voltage. 

The included EOL-Z Connector Element (Part No. 808625) is to be used for monitoring of 

the automatic standard detector per used detector group. The EOL-Z is to be connected to 

the terminal of the respective detector base. 



Rated current @ 19 V DC < 350 μA 

External supply of the rated voltage 2 10 V DC to 28 V DC 

External supply of the rated voltage 5 max. 28 mA 

External supply of the closed-circuit current 

Detector zones 

< 6 mA @ 12 V DC 

Current 25 mA (current limiting) @ 9 V DC 

Contact load max. 30 V DC / 1 A or 48 V DC / 0,5 A 

Relay monitoring 10 kƒ / ±40% 





Dimensions (W x H x D) 72 x 65 x 20 mm (PC board) 

Corresponding connection examples for FSA transponder operation in stand-alone operation or 

as a device in the fire detection system 8000 can be found in the chapter containing automatic 

door release systems. 

2 x EOL-Z (Part No. 808625) 

Accessories: 






788651.10 Housing flush mount, white


808622 

808630.10 

¬qw7,− 

¬qw?§/21¨− 

esserbus Transponder for UniVario 

Approval: 

The esserbus transponder works as a loop device on the multifunctional primary line. 

Input transponder with 4 monitored contact inputs for the activation of detectors from the 

UniVario family of products. Two floating relay contacts for controlling functions are additionally 

available. 

- max. 31 esserbus transponders on a multifunctional primary line 

- max. 1 detector from the UniVario family of products per zone 


Refurbishment zone transponder RZT 8000 

Approval: 

VdS 

Analog loop 


Rated current @ 19 V DC approx. 250 μA 

















2 x EOL-Z (Part No. 808625) 

Accessories: 






VdS 

The refurbishment zone transponder is a stand-alone participant on the esserbus for the Fire 

Alarm System 8000 and IQ8Control fire alarm control panels. Individual automatic fire 

detectors and manual call points (conventional technology) from other manufacturers can 

be connected to the 4 zone inputs. The voltage of all 4 zones can be configured to 24 V via 

the internal DC / DC module. An additional reset module is not required to operate thirdparty 

detectors. 


Operating voltage 10,5 V DC to 13,8 V DC 


Detector zone current imit of 125 mA per detector zone 

Contact rating 30 V DC / 1 A, 48 V AC / 0,5A 

Relay monitoring 10 kOhm / +/ - 40% 





Whether or not a connection is possible must be individually checked in advance by the technical 

sales department. 

165 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

166 


808631.10 

808621 

772384 

772388.10 

783259 

783257 

783258 


¬qw@§/21"− Refurbishment zone transponder (RZT) / 12V - Esser 

As 808630.10, but rated voltage is 12 V DC, not configurable. 

¬qw6)− esserbus Transponder 4 IN / 2 OUT - Esser, Dutch 

¬n8ue− esserbus Transponder 4E 2S 808613.F0 with housing - Esser, French 

¬n8y§/21L− Refurbishment zone transponder RZT 8000 w. housing - Esser, French 

¬oA\-− MD2L Transponder - Esser, French 

Transponder 2 remote control lines in plastic housing. 2 remote lines and positioning 

control. 

¬oAZ'− MD4L Transponder - Esser, French 

Transponder 4 remote control lines in plastic housing. 4 remote lines and positioning 

control. 

¬oA[*− MD1L Transponder - Esser, French 

Transponder 1 remote control line in plastic housing. 1 remote line and positioning 

control.


Accessories esserbus Transponders 

788612 

808625 

¬ow-s− 

¬qw:5− 

788600 esserbus transponder housing surface mount grey 

788650.10 esserbus transponder housing surface mount white 

788601 esserbus transponder housing flush mount grey 

788651.10 esserbus transponder housing flush mount white 

788605 Mounting kit 

788602 Top-hat rail 

788652 Mounting rail for FACP 8000 C/M and IQ8Control C/M housing 

788603.10 Module housing 

Loop isolator for transponders 

Loop isolator PCB to be mounted on esserbus transponders. To isolate short circuit failure 

and wire break on the loop. 


Operating voltage 6 V DC (via esserbus transponder) 

Rated current 3 μA 







EOL-Z Module for detector groups 

Terminating device for the monitoring of standard-inputs when using esserbus transponders 

(Part No. 808613.20, 808622, 808619.10). 

167 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

168 


Technical Alarm Modules 

Series 9200 

804863 

804864 

805863 


¬qQ`[− 

¬qQa^− 

¬q[ò− 

TAL optocoupler input / isolator - Esser, German 

Detection, forwarding and individual indication of a technical alarm (TAL) specially for the 

requirement as loop device on the multi-functional primary line for the Fire Alarm System 

8000 and IQ8Control. The TAL module contains an isolator for error exclusion on the multifunctional 

primary line. There is an optocoupler input available as well as a monitored input. 

The maximum line length at the monitored input must not exceed 500 meters! 



Contact rating 30 V DC / 1 A 

Optocoupler input DC 2.4 V to 24 V/0.4 to 15 mA 


Emergency operation alarm typ. 18 mA 


Ambient temperature -20 °C to + 70 °C 

Storage temperature -30 °C to + 75 °C 



Colour grey-white, similar to RAL 9002 



Surface mount installation 


TAL optocoupler input /relay - Esser, German 

As 804863; relay output instead of isolator. 


Relay output/switch contact potential-free changeover switch 

Loading capacity 30 V / 1 A 


TAL optocoupler input / isolator 

As 804863, but with Makrolon housing. 






Phase-out date: 01.01.2009


805864 

804869 

¬q[ar− 

¬qQfm− 

TAL optocoupler input / relay IP 54 

As 804864, but with Makrolon housing. 







IQ8TAM technical alarm module for snap-on mounting 

Approval: 


VdS 

The technical alarm module IQ8TAM is a bus device of the fire alarm system 8000 for recognition, 

transmission and individual display of technical alarms. 

Each IQ8TAM includes an integrated loop isolator, which opens in case of loop short circuit 

to isolate the part of the loop between two loop isolators. A single wire break does not effect 

the loop and all devices remain in operation. The module does not require external voltage 

supply, as voltage is supplied by the field bus. 


Quiescent current @ 19 V DC approx. 45 μA (medium) 

Alarm current w/o communication curtain approx. 18 mA 

Alarm display red LED, Ø 3 mm 

Connection terminal max. 1,5 mm 2 



Relative humidity ¥ 95% rel. humidity (non-condensing) 

Housing PA 66 - plastic 





The module can either be mounted in an appropriate installation position in the housing of the 

fire alarm panel or, for example, on a C-rail of a switch cabinet. Each module can be individually 

connected or cascaded directly snap-on or on side connector block. 

incl. 4 screw clamps and 1 resistor 


169 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

170 


804870 

IQ8 

804868 

Features 


¬qQgp− 

¬qQej− 

• One contact input and one floating relay output 

• Voltage supply via the field bus 

• Test and reset function 

• Higher IP protection optional 

• Programmable inverse monitoring functionality 

(1k resistance latent / 10k resistance fire) 

Alarm and monitoring module for IQ8TAM 

An external, monitored contact can be connected to the terminals of the IQ8TAM technical 

alarm module for C-rail mounting with Part No. 804869. In case of contact activation, the 

address and the programmed additional text of the corresponding IQ8TAM technical alarm 

module will be displayed. 

For contact monitoring, the alarm and monitoring module for IQ8TAM (Part No. 804870) is 

required. 


Alarm resistance 1kOhm 

Terminating resistor 10kOhm 

IQ8TAL Technical Alarm Module 

Approval: 

The max. cable length to the connected module must not exceed 250 meters! 


requested 

The IQ8TAL Technical Alarm Module is a full-fledged loop device of the IQ8Control fire 

detection system and it facilitates the detection and forwarding of technical alarms. 

The IQ8TAL is equipped with an integrated loop isolator, a contact input and a relay output. 

The relay can be optionally configured as a normally-closed contact or as a normally-open 

contact. The IQ8TAL does not need a separate voltage supply. 

In order to increase the IP protection class, the optional IP protection kit (Part No. 704965) 

can be used. 

The functionality of the Technical Alarm Module can be tested with the included key and the 

alarm status can be reset directly at the IQ8TAL. 



Alarm current approx. 9 mA, pulsed 

No. of detector max. 127 detectors per loop 

Alarm display red LED 

Operation indicator green LED 


Application temperature -20 °C to +70 °C 



IP 55 (with optional IP Kit 704965) 

Housing PC/ASA plastic 



Dimensions (W x H x D) 88 x 88 x 21 mm (Housing) 

88 x 88 x 57 mm (with surface-mounted housing) 

Specification EN 54-18 / -17 

2 x 10k (terminating), 1x 10k pre-assembled, and the rest included as additional package 

1 x 1k (alarm), 

1 x 6k8 (inverse operation) 

not available until Q1/2009 

Accessories: 

704965 MCP Cover for small housing, transparent 

704981 Surface mount housing for small MCP, blue

Wireless component Wireless modules 172 - 178 

171 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

172 

Wireless component Wireless modules 

Features The following wireless modules are only compatible with IQ8Control panel. Communication 

Radiocommunication transmission features 

• Interference-proof transmission via dual band 

with frequency hopping 

• Bi-directional data traffic 

• Permanent automatic interference monitoring of 

transmission path 

• In case of interferences, automatic modification of 

frequency band and radiocommunication channel 

• Band blocking detection 

• High transmission range (in the open air: max. 

300m) 

• Automatic interference detection due to low field 

strength levels 


between the RF devices is set up via a dual band transmission mode. The RF-technology 

applys frequency hopping to enable highest transmission security. In case of interference, 

the frequency band and the radiocommunication channels are automatically modified. If the 

entire band and the receiver are blocked due to high interference level, a fault signal is transmitted 

to the fire alarm panel. Thus, secure and reliable wireless transmission is provided. 

The transmission range in open air is up to 300m. Inside the building, the transmission 

range varies, depending on building structure, wall thickness or use of concrete steel. 

IQ8Wireless radio technology facilitates the cable-free connection of IQ8Quad automatic fire 

detectors (with and without alarm signalling devices), manual call points and the IQ8Alarm 

alarm signalling device to the IQ8Control fire alarm system. 

Already existing fire alarm systems can be expanded using the wireless technology or complete 

fire alarm systems can be realised for smaller objects with wireless components as 

well. 

The allocation of the wireless components to a wireless transponder or wireless gateway 

takes place via the tools 8000 programming software. 

The status of the batteries is checked automatically and their necessary replacement is 

displayed early on as a detector failure on the fire alarm control panel and/or the wireless 

transponder*. 

The optimal installation site as well as the maximum possible transmission distance can be 

conveniently and quickly transmitted via the tools 8000’s integrated field strength measurement. 

* during allocation of the wireless components via wireless transponder 

Please take into account that the use of wireless components requires an extra training, covering 

project planning and commissioning. For further information see our training brochure. 

These devices were designed, produced and labelled for operation within the countries of the 

European Union (EU) in accordance with the current EU standards and requirements. In case 

the device is installed outside of the EU, national guidelines and requirements must be taken 

into consideration. 

For further information, please contact your local sales representative. 

Using components like IQ8Alarm and IQ8Quad with intergrated alarm devices the esserbus 

PLus is needed. 

Connection example


805593 

Features 

¬qX~\− 

The wireless detector base suitable for 

• Fixed heat detector (Part No. 802171) 

• Rate-of-rise heat detector (Part No. 802271) 

• Optical smoke detector (Part No. 802371) 

• O 2T multisensor (Part No. 802374) 

• OTG multisensor (Part No. 802473) 

The wireless detector base features 

• Individual detector identification on the control 

panel 

• Regular functionality check for each detector 

(alarm and operation display on the detector) 

• Alarm and fault transmission in accordance 

with EN 54-2 

• Easy detector or battery replacement with 

detector removal tool 

• Fault signal when the mounted wireless base 

and the inserted detector are removed 

• Permanent monitoring of battery voltage 

• Up to 5 years battery life depending on 

detector type and environmental conditions 

IQ8Wireless detector base 

Approval: 


VdS 

With the IQ8Wireless base, the wireless component is located in the base onto which the 

respective fire detectors is placed. The wireless base facilitates the connection of the 

IQ8Quad TM, TD, O, O 2 T and OTG detectors via a wireless transmission line to the 

esserbus/esserbus-PLus and integrates them via wireless transponder or wireless gateway 

into the fire alarm system. 

A maximum of 32 radio bases per wireless transponder and/or 10 per radio gateway can be 

allocated. 

Operating voltage 4 x 3.6 V battery 

Battery operating time up to 5 years depending on detector type 

Current consumption approx. 50 μA 

Range inside approx. 30 m 

Range outside approx. 300 m 


Storage temperature without batteries -20 °C to +70°C 

with batteries +25 °C +/- 10 °C 



Material ABS-V0 


Weight 315 g (including batteries) 

Dimensions (Ø x H) 135 x 49 mm (with detector H: 88 mm) 

The batteries to be used are components of the device approval according to EN 54 and are 

specified by the manufacturer. With the IQ8Wireless radio components, only the approved batteries 

with part no. 805597 may be used. Use of batteries other than those specified by us 

automatically voids the product’s device approval (VdS-approval) and may not be used for 

example in Germany in fire alarm systems under legal building regulations. 

4x 3.6V lithium batteries 805597 and 1x standard detector base for IQ8Quad 805590 with an 

additional factory-installed wire jumper 

Accessories: 

805597 4 x 3.6V lithium batteries 

173 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

174 


805594 

Features 


¬qX¡_− 

• The wireless gateway can be mounted between 

detector base and IQ8Quad detector. No additional 

wiring required 

• Suitable for IQ8Quad detectors w/o alarm 

devices 

• Wireless communication with up to 10 users 

• maximum 10 wireless bases 

• maximum 10 wireless interfaces with IQ8MCP 

manual call points 

• maximum 10 control groups for wireless interface 

with IQ8Quad/IQ8Alarm alarm signalling 

devices 

• All wireless devices are integrated as individually 

addressable on the esserbus / esserbus- 

PLus 

• esserbus integration of all radiocommunication 

devices as individually addressable users 

• The radiocommunication devices can be allocated 

in up to 10 detector zones 

• Up to 9 wireless gateways per loop 

• Alarm and trouble transmission in accordance 

with EN 54-2 

• Easy detector or battery replacement via 

detector removal tool 

• Trouble signal when removing the gateway and 

the detector 

• Permanent monitoring of battery voltage 

• Up to 5 years battery lifetime depending on the 

detector type and environmental conditions 

IQ8Wireless gateway for devices 

Approval: 

This wireless gateway is especially designed for convenient and time-saving expansion of 

an already existing IQ8Control fire detection system. By removing a detector already 

installed on the loop and adding the wireless gateway to the standard IQ8 detector base, up 

to 10 additional fire detectors equipped with wireless detector bases or 10 addressable 

manual call points can be added to the existing system. Up to 10 components with alarm 

signalling functions – IQ8Alarm alarm signalling devices and/or IQ8Quad fire alarms with 

integrated alarm signalling device – can be connected per wireless gateway via the universal 

wireless interface. And all this without any additional cabling. Depending on the surrounding 

conditions, the wireless transmission can reach up to 200m. The wireless gateway must 

fundamentally be operated with an IQ8Quad detector. It integrates the intelligent IQ8 wireless 

components into the esserbus or esserbus-PLus via the wireless base or wireless interface, 

thus making these components fully individually addressable loop devices. 

Up to 9 wireless gateway can be operated on the loop. Each wireless gateway reduces the 

maximum number of esserbus devices by 12 pieces. 


VdS 


Voltage supply 4 x 3.6 V battery 

Battery operating time up to 5 years 

Current consumption 400 μA to max. 2,5 mA 

Range inside approx. 20 m 

Range outside approx. 200 m 


Storage temperature without batteries -20°C tos +70°C 

with batteries +25°C +/- 10°C 



Material ABS 


Weight approx. 265 g (including batteries) 

Dimensions (Ø x H) 135 x 49 mm (with detector H: 88 mm) 

The standard detector base version IQ8Quad 805590 is not included in the RF gateway package. 






4x 3.6V lithium batteries 

Accessories: 

805597 4 x 3.6V lithium batteries


805595 

Features 

¬qX¢b− 

• RF communication with up to 32 users 

• maximum 32 wireless bases 

• maximum 10 wireless interfaces with IQ8MCP 

manual call points 

• maximum 10 control groups for wireless interface 

with IQ8Quad/IQ8Alarm alarm signalling 

devices 

• esserbus integration of all RF. Devices as individually 

addressable users 

• The RF devices can be assigned in up to 32 

detector zones 

• Alarm and fault transmission in accordance 

with EN 54-2 

• Connection to esserbus of IQ8Control panel as 

bus device as well as to a conventional 

detector zones 

• Stand-alone operation 

• Potential-free outputs for common fault and 

common fire 

IQ8Wireless transponder for devices, wall mount 

Approval: 


VdS 

This wireless transponder is designed for wall mounting. The wireless transponder communicates 

with to to 32 other wireless devices. These can be wireless of various types from 

intelligent automatic fire detectors or wireless interfaces with manual call points and/or 

alarm signalling devices of the IQ8-family. Using the System IQ8Control, the wireless transponder 

integrates the intelligent automatic detectors (with and without alarm signalling 

devices), manual call point and alarm generator IQ8Alarm in the esserbus / esserbus-PLus 

via the wireless base and/or wireless interface. The detector base allows esserbus integration 

of intelligent automatic detectors as bus devices with individual addressing via the 

transponder. Up to 10 transponders can be operated on one loop. The transponder can be 

linked with the loop as well as with a conventional detector zone or it can be operated as a 

stand-alone unit. Potential-free outputs for common fault and common fire are available. For 

system 8000 the transponder for RF devices can only be connected by using a potential-free 

relay to 4IN/2Out or 1IN transponder, because it is not compatible with panel 8000 and it 

cannot be used as bus device. 

The transponder needs an external supply voltage for operation. 


Contact load relay 30 V DC / 1A 



Range inside to 30 m 

Range outside to 300 m 




Housing ASA + PC 



Dimensions (W x H x D) 200 x 280 x 39 mm (incl. antenna) 

The external power supply of the IQ8Wireless transponder can come from the fire alarm control 

panel or from an external power unit. 

The voltage for the wireless transponder can be supplied by the fire alarm control panel or an 

external power supply. An individual, separately protected supply line is to be installed for the 

voltage supply. The external voltage supply is monitored by the wireless transponder. If the 

wireless transponder is installed as a device on the IQ8Control fire detection system analogue 

loop, a disturbance is transmitted to the fire detection control unit via the loop and is indicated 

there. 

175 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

176 


805601 

Features 


¬qY"¡− 

Radio interface suitable for: 

• IQ8 manual call point - electronic module, large 

design (Part No. 804905/ 804906) 

• IQ8 manual call point – complete package, 

small design (Part No. 804971) 

• IQ8 manual call point - electronic module, 

small design (Part No. 804955), only with 

mounting frame (Part No. 704967) 

• IQ8Quad detectors (with and without alarm signalling 

devices) 

• IQ8Alarm alarm signalling device (part no. 

8073xx) 

Radio interface features: 

• The IQ8 components are individually identified 

on the fire alarm control panel 

• Regular functionality performance checks of 

IQ8 components 

• Fault signal when the IQ8 components are 

removed from the fire alarm control panel 

• Operating mode display directly at the IQ8 

manual call point and IQ8Quad detector 

• Alarm and fault message transmission in compliance 

with EN 54-2 

• Easy detector removal and battery replacement 

using multifunctional key 

• Remote operation of IQ8 components possible 

(max. 3 meters) via 2-wire line 

• Constant battery status monitoring 

• Early battery replacement notification at the fire 

alarm control panel 

• Battery life of up to 5 years 

IQ8Wireless universal interface w/o cover, red 

Approval: 

VdS 

The radio interface allows the IQ8 manual call point (small or large design) to be connected 

on the wireless esserbus-PLus. 

The radio interface connects the intelligent IQ8 manual call point to the esserbus/powered 

loop via the IQ8wireless transponder or the IQ8wireless gateway. Thus, the devices are 

automatically converted into individually addressable loop devices. 


Operating voltage 4 x 3.6 V batteries 

Operating time 2 to max. 5 years 

Current consumption approx. 30 μA 

Frequency band 1 433 / 868 MHz 

Range to max. 300 m 


Storage temperature without batteries: -20 °C to +70 °C 

with batteries: +25 °C ± 10 °C 

Air humidity ¥ 95 % rel. Humidity (non-condensing) 


Material PC/ASA plastic 


Weight approx. 285 g incl. Batteries (without attachment) 

Dimensions (W x H x D) 135 x 135 x 20 mm (without attachment) 

Only use small manual call points with mounting frame part no. 704967. 






4 x lithium battery 3.6V (Part No. 805597) 

Application example for large MCP 

Application example for small MCP


805602 

805603 

805604 

¬qY#¤− 

IQ8Wireless universal interface w/o cover, white 

Approval: 

as 805601, but 


VdS 


¬qY$§− IQ8Wireless mounting frames for IQ8Alarm, red and white 

The mounting frame is used for the mounting of the IQ8Alarm alarm signalling devices onto 

the IQ8Wireless wireless interface 805601/805602. 



white, similar to RAL 9010 




¬qY%!− IQ8Wireless mounting frame for IQ8Quad detectors, white 

The mounting frame is used for the mounting of the IQ8Quad fire detector with or without 

integrated alarm signalling device onto the IQ8Wireless wireless interface 805602. 






177 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

178 


805605 


¬qY&$− 

IQ8Wireless cover for wireless interface, red and white 

For applications in which the IQ8 components are not to be directly mounted (remote connection) 

on the IQ8Wireless wireless interface 805601/805602, the wireless interface can 

be used with the filler panel. 



white, similar to RAL 9010 



1 x red cover plate 

1 x white cover plate 

Application example

Detectors for 

Special Applications Flame Detectors 180 - 183 

Air duct detector f. 

IQ8Quad Detector 184 - 190 

Line Heat Detectors 191 - 192 

Line Smoke Detectors 193 - 199 

Aspirating Smoke Detectors 200 - 227 

Accessories 228 

179 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

180 

Detectors for Special Applications Flame Detectors 

782313 

Features 

• Direct linking and voltage supply via standard 

detector group at the esserbus transponder 

(Part No. 808622) 

• Base installation and alignment via included 

mounting bracket (Part No. 783312) 

• High IP protection for indoor and outdoor 

usage 

• Operation and fault status displayed on the 

detector 

• Self-monitoring via internal sensors 

783312 

783313 


¬o8._− 

UV Flame Detector UniVario Type FMX5000UV.ESSER 

Approval: 

VdS 

UV flame detector for the recognition of fast developing fires with flame formation. Operation, 

fault and fire statuses are displayed via LEDs on the detector. The supply voltage and 

the linking takes place directly via the standard detector zone 

at the esserbus transponder (Part No. 808622). Resetting of the detector is also carried out 

directly via the esserbus transponder (Part No. 808622). 



Quiescent current @ 9 V DC approx. 0,5 mA 



Area to be monitored max. 676 m2 Angle of vision 90° 

No. of detector/zone 1 



Relative humidity ¥ 95 % rel. humidity (non-condensing) 


Housing Die cast aluminium 


Weight approx. 945 g(incl. base and bracket) 


Detector and standard base, mounting bracket 

¬oB-p− Mounting bracket for UniVario Flame Detector 

Mounting bracket for alignment of the UV flame detector (Part No. 782313). 

¬oB.s− UniVario MX5000.ESSER standard base 

Standard detector base for detectors of the UniVario product family.


Explosion-Proof Detectors 

761347 

Features 

• Visual range: 90° 

• Maintenance with magnets, no test lamp 

required 

• Status display directly at the detector via 3colour 

LED for operation, fault and alarm 

• Actuation and resetting via esserbus transponder 

808613.10 in loop operation 

¬m.PH− 

IR flame detector (ex) X 9800 

Approval: 


VdS 

The pressure-proof, fully enclosed flame detector particularly distinguishes itself through 

reliable operation in difficult conditions. An integrated LED and three relays provide information 

regarding the state of operation, failure, and alarm. Contamination resistance and 

heated optics to prevent condensation and formation of ice also allow for external operation. 

Typical areas of application are turbines, petrochemistry and the automotive industry. 

Activation on the loop and resetting take place via the esserbus transponder 808613.10. 

Activation on a conventional line occurs via the reset module 781332. This device requires 

a separate voltage supply of 24 V DC. 

Operating voltage 18 - 30 V DC 



Power consumption 16.5 W @ 30 V DC with end-of-line 

resistor and heater on maximum 

Weight 2,7 kg + 6 kg fixture 


Angle of vision max. 90° 

Ex-category II 2 GD 

Explosion protection EEx d IIC T5-T6, T86°C 


Housing material aluminium 

Detector specification EN 54-10, Class 1 

EC-type examination certificate DEMKO 02 ATEX 132195 

Please note: for mounting of the holder, a 14 mm Allen key is necessary and is not included in 

delivery. 

Mounting bracket 

181 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

182 


761348 

Features 



required 






¬m.QK− 

UV flame detector (ex) X 2200 

Approval: 

The pressure-proof, fully enclosed flame detector possesses automatic optical self-monitoring 

that allows any application under difficult conditions. An LED provides information 

regarding the state of operation, failure and alarm. Three relays (fire, failure and additional 

alarm) are integrated for connection to a fire detection system. Contamination resistance 

and heated optics to prevent condensation and formation of ice also allow for external operation. 

Typical areas of application are turbines, munitions depots, natural gas depots and 

aircraft hangers. 





VdS 




Power consumption 7.6 W @ 30 V DC with end-of-line resistor 

Weight 2.7 kg + 6 kg fixture 

Type of protection IP66 








Please note: for mounting of the holder, a 14 mm Allen key is necessary and is not included in 

delivery. 

Mounting bracket


761349 

Features 



required 





¬m.RN− 

UV/IR flame detector (ex) X 5200 

Approval: 


VdS 

Since it can be mounted, the pressure-proof, fully enclosed combination flame detector, 

enables UV and IR transmitters to monitor the same danger zone with a visual angle of 90°. 

Triggering occurs only by activation of the IR and UV sensors. An LED provides information 

regarding the state of operation, failure and alarm. Three relays (fire, failure and additional 

alarm) are integrated for connection to a fire detection system. Contamination resistance 

and heated optics to prevent condensation and formation of ice also allow for external operation. 

Typical areas of application are turbines, munitions depots, natural gas depots and 

aircraft hangers. 







Power consumption 17.5 W @ 30 V DC with end-of-line resistor and 

heater on maximum 

Weight 2.7 kg + 6 kg fixture 






Dimensions (Ø x L) 122 x 246 mm 



Please note: for mounting of the holder, a 14mm Allen key is necessary and is not included in 

delivery. 

Mounting bracket 

183 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

184 

Detectors for Special Applications Air duct detector f. IQ8Quad Detector 

781443 

Features 

Application example with detector 


¬o/L@− 

• Single-tube air analysis system based on the 

Venturi principle 

• Optimum utilisation of air flow velocity through 

new Venturi tube design 

• Integrated maintenance opening in the front 

cover so that air duct smoke detector can be 

tested 

• Suitable for air duct widths from 0.6 to 2.8m 

• Integrated air flow display 

Venturi air duct module for IQ8Quad OT blue -LKM (802379) 

Ventilation air duct module for usage of the OT blue -LKM 802379 air duct smoke detector in 

combination with Venturi tubes 781446, 781447 or 781448. The module is mounted on the 

outside of the air ducts. 

The Venturi tube enters the duct and leads the air out of the duct through the detection 

chamber of the detector back to the duct and finally back into the duct. During operation, 

the detector and the alarm LED is visible so that an external parallel detector indicator is not 

required. 

The housing need not be opened for maintenance purposes. Inspection of the detector can 

be quickly easily performed via a separate opening in the front of the housing. 


Width of the vent 140 to 2700 mm 

Adapter housing ABS plastic 

Colour grey 


Weight 800 g 


Construction kit includes pipe gasket and cap. The following items are not included: IQ8Quad 

OT blue LKM or detector base as well as the Venturi tube or filter cartridge.


Accessories 

802379 

781444 

781446 

781447 

¬q8pY− 

¬o/MC− 

¬o/OI− 

¬o/PL− 

IQ8Quad OT blue -LKM 

Approval: 


VdS 

Specially addressable IQ8Quad multicriteria detector for application as air duct smoke 

detector in construction kit 781443. The detection methods are based on state-of-the-art 

sensor technology that enables the detection of open fires, smouldering fires and fires with 

intense heat generation. In addition to that, extremely small particles can be detected 

without using ionisation detectors. The loop isolator is integrated in the detector. 



Quiescent current @ FACP battery 0,20 mA @ 27,5 V / 0,28 mA @ 42V 




Housing ABS plastic, white, similar RAL 9010 


Dimensions (Ø x H) 117 x 62 mm 


Only suitable for application in air duct construction set 781443. 

Filter cartridge for air duct module 781443 

For use in unclean environmental conditions. 

Venturi tube 0.6m for IQ8Quad air duct construction set 781443 

Venturi tube 0.6m for application with air duct construction set 781443 between 140mm 

and 600mm. 

Required borehole in the duct: 38mm 



and 1400mm. 


Venturi tube, plastic gasket and rubber seal 

185 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

186 


781448 

781449 

781445 


¬o/QO− 

¬o/RR− 

¬o/NF− 



and 2700mm. 



Mounting set for round and insulated air ducts 

Mounting set for mounting the 781443 air duct construction set to round and / or insulated 

air ducts. 


Weather protection housing for air duct construction set 781443 

Protects the air duct detector in difficult environmental conditions such as during use in outside 

areas. 

The weather resistant housing can be subsequently fixed above the already mounted and 

installed air duct module 781443. 


Weight 1.8 kg 

Material galvanised steel 


Class of protection IP 65 

Opened condition


781453 

¬o/V^− 

Venturi principle air duct kit 

Air duct kit for use with the Venturi tubes 781456, 781457 or 781458 in combination with 

the 801979 air duct detector. The kit is mounted outside the air duct. The Venturi tube dips 

into the air duct. The built-in detector can be accessed by removing the transparent plastic 

cover. During operation, the detector alarm LED is visible. 


Connection terminal 0.6mm ø to max. 1.5mm2 Air speed 1m/s to max. 20m/s 





Colour grey 



Kit including filter element 

Not included: detector, detector base, Venturi tube 



187 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

188 


Accessories 

801979 

781454 

781456 


¬q4pQ− 

¬o/Wa− 

¬o/Yg− 

OTI-intelligent fire detector for 781453 

Approval: 

Special multisensor intelligent detector for use in air duct detector kit (781453) at wind 

speeds from 1 to 20m/s. 


VdS, CNBOP 


Type of protection IP 40, IP 43 with base adapter 781498 




Display red LED / light pipe 

Radioactive compound Am 241 ¥ 5kBq 


Licence of construction type NW 609/90 

Dimensions (Ø x H) 90 x 61 mm (72 mm incl. socket) 


Housing ABS plastic white, similar to RAL 9010 

Relative humidity max. 95% (without condensation) 

Only approved for application in 781453 air duct kit. 

Please take note that this item has to be handled as dangerous good (radioactive substance) 


Spare filter 

Spare filter insert for 781453 air duct kit. 


Venturi tube, 0.6m 

Venturi tube 0.6m for kit 781453 for channel widths of 140 to 600mm (can be cut). 


Material aluminium 

Required hole size: 35mm on the detector 



781457 

781458 

781459 

¬o/Zj− 

¬o/[m− 

¬o/\p− 


For kit 781453 for channel widths of 600 to 1400mm (can be cut). 



Required hole size: 35mm on the detector and 50mm 

on the opposite side 

Venturi tube, plastic cup seal and rubber seal 



For kit 781453 for channel widths of 1400 to 2700mm (can be cut). 



Required hole sizes: 35mm on the detector and 50mm on the opposite side. 

Venturi tube, plastic cup seal and rubber seal 


Mounting kit for round and insulated air ducts 

Mounting kit for 781453, to be used on round and insulated air ducts. In this case, the tube 

mounting hole on the mounting side of the kit 781453 must have a diameter of 50mm. 

rubber seal included 


189 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

190 


781460 


¬o/]s− 

Weather protective cover for air duct kit 781453 

When using the air duct kit 781453 in outside areas or in unheated attics, the wheather protective 

housing protects against humidty and dust from entering the detector. 

The protective frame and protective cover can be installed afterwards on the already 

mounted air duct kit. The protective cover could be dismounted for maintenance and inspection 

purposes. The cover is fitted on the installation frame and fixed with one screw. 


Material electro-plated metal sheet 



Protective cover and installation frame 


Application example

Detectors for Special Applications Line Heat Detectors 

Line Heat Detector 

761290 

Features 

• Maximum sensor length of 300m 

• Resistant against mechanical and chemical 

impact, corrosion, humidity and dust 

• Calibration switch setting 

• VdS approval as per EN 54-5 A1 applicable up 

to 7.5 m ceiling height 

• Early fire detection with heat detector classes 

A1, A2, B and C 

• High chemical and / or mechanical resilience 

by using special sensor cables 

• applicable for to 7.50 m ceiling height 

• 2 floating relay contacts for fire and fault 

disturbances 

• separate reset input for resetting via esserbus 

transponder 808613.10 during loop operation 

Accessories 

761243 

¬m-{`− 

¬m-L:− 

Line heat detector LWM-1 

Approval: 

The LWM-1 enables early detection of fires or overheating. It is specifically designed for 

application in narrow rooms or rough environmental conditions. The system consists of an 

LWM-1 evaluation unit and a special sensor cable, which must be selected according to the 

type of application. The actuation on the loop and the resetting function is carried out via 

the esserbus transponder 808613.10. 

Actuation on a conventional line is carried out via the reset module 781332. The device 

requires a separate voltage supply of 24V DC for the galvanic separation of D.C. voltage 

potentials and the voltage converter 781337 is to be used in order to avoid ground faults. 


Operating voltage 10 V to 30 V 






Temperature range -20°C to +50°C 

Sensor length / evaluation unit max. 300 m, min. 10 m 

Voltage 10-30 V DC 

Quiescent current @ 24 V DC max. 25 mA 

Current consumption for DIF-ALARM or MAX-ALARM: 

max. 25 mA (@ 24 V) 

Current consumption in the case of failure max. 15 mA (@ 24V) 

Starting current @ 24 V DC < 100 mA 

Display LED green: in operation, permanent light; 

LED red: alarm diff., permanent light, locked; 

LED red: alarm max., permanent light, locked; 

LED yellow: fault, flashing light, locked 

Range max. 300 m 

The fastening clamp for mounting the line heat detector can be purchased at wholesale. 


VdS 

Termination link set for sensor cable 

The set contains four links for one end point. 

191 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

192 

Detectors for Special Applications Line Heat Detectors 

761244 

761245 

761246 

761247 


¬m-M=− 

¬m-N@− 

¬m-OC− 

¬m-PF− 

Connection link set for sensor cable 

The set contains six links for one interconnection point. 

Sensor cable blue (PVC) 

Sensor cable for use in non aggressive atmosphere, but with high humidity for the 761260 

and 761290 line heat detector. 

The price stated is the price per metre. Order quantity at least 5m or a multiple there of. 

Sensor cable black 

Sensor cable with nylon cover for protection against acids and bases for the 761260 and 

761290 line heat detector. 

The price stated is the price per metre. Order quantity at least 5m or a multiple there of. 

Sensor cable black, with steel braiding 

For reducing the mechanical loading of the cable under extreme conditions for the line type 

heat detector 761260 and 761290, the sensor cable is additionally protected by a stainless 

steel braid. 

The price stated is the price per metre. Order quantity at least 5 m or a multiple there of. Cancellations 

or returns are not possible.

Detectors for Special Applications Line Smoke Detectors 

Line Smoke Detector LRMX 

Features The LRMX Line Smoke Detector marks a new generation of infrared light-beam detectors in 

• Motorized detector head 

• User-friendly commissioning via automatic selfadjustment 

• Disturbance-protected operation via automatic 

electromechanical tracking of the detector head 

during building movements 

• Optimal access via remote operating unit at eye 

level 

• Clear representation of all states via central indicator 

display on the operating unit 

• High level of IP protection for usage under difficult 

environmental conditions 

• Activation and reset via esserbus Transponder 

808613.10 during loop operation 

• Ranges from 5 to 100 m 

• Large assortment of accessories 

compliance with EN 54-12. 

Based on the light absorption principle, the sender sends a pulsated infrared beam of light 

to the prism reflectors which are to be mounted opposite the detector. These prisms reflect 

the light back to the receiver. If smoke should enter the infrared light beam and dim it to a 

defined degree, a signal is forwarded via the esserbus Transponder to the fire alarm control 

panel (FACP). Both fire alarms as well as disturbance alarms are forwarded to the FACP. 

The prominent feature of this new generation is the automatic alignment at initial start-up 

and the regular adjustment of the detector head via the integrated engine in the detector. 

This simplifies start-up considerably and thus it can be carried out more quickly. Due to the 

automatic self-adjustment of the detector during even the slightest building movements, as 

for example due to length extensions, temperature variations, etc., the LRMX can always 

retain the optimal position of the initial alignment and thus is even more protected from 

disturbance. 

Operation is user-friendly via the ground-level operating and control unit which is operated 

remotely from the detector. The power is supplied directly to the detector, so that in the case 

of an operating and control unit failure, continuing operation of the LRMX is guaranteed. 

The operating and control indicator has an indicator display which shows all reports and 

states clearly and at eye-level. 

With the aid of the display, a manual alignment of the detector is also possible even in the 

case of very difficult initiation conditions, as the horizontal and vertical coordinates of the 

infrared light-beam are represented in detail. 

The connection to the esserbus-loop is carried out via the esserbus Transponder 808613.10 

in the usual manner. Resetting can also be easily carried out via this esserbus Transponder: 

using the tools 8000 programming and service software, the relays on the transponder can 

be programmed as reset relays and the reset time can be set individually. 

In conclusion, the LRMX on the esserbus represents a significant advance in the world of 

line smoke detectors and guarantees an extremely high degree of disturbance-free and lowmaintenance 

operation. 

Application Example 

193 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

194 


761400 

Features 

• Motorized detector head 

• User-friendly commissioning via automatic 

self-adjustment 

• Disturbance-protected operation via automatic 

electromechanical tracking of the detector head 

during building movements 

• Optimal access via remote operating unit at eye 

level 

• Clear representation of all states via central 

indicator display on the operating unit 

• High level of protection from moisture for 

usage under difficult environmental conditions 

• Activation and reset via esserbus Transponder 

808613.10 during loop operation 

761401 

761402 


¬m/!$− 

¬m/"'− 

¬m/#*− 

Linear Smoke Detector LRMX 

Approval: 

The linear smoke detector in compliance with EN 54-12 consists of detector, operating and 

control unit and one prism reflector. 

The connection to the esserbus and the resetting is carried out via the esserbus Transponder 

808613.10. The connection to a conventional detector zone is carried out via the Reset 

Module 781332. 

This device requires a external voltage supply of 24 V DC for the galvanic separation of D.C. 

voltage potentials and the voltage converter 781337 is to be used in order to avoid ground 

faults. 

This device works with the use of a prism reflector at a range of from 5 m to 40 m. AT larger 

ranges, the Range Extender 761401 or 761402 should be used. 


VdS 

Operating voltage 10.2 to 40 V DC 

Current consumption 3 mA (in all operational states) 

IR Wave Length 870 nm 

Alarm relay 30 V DC / 2 A 

Fault Relay 30 V DC / 2 A 

Range 5 to 40 m 


Dimensions (W x H x D) Detector: 155 x 180 x 137 mm 

Operating Unit: 120 x 185 x 62 mm 

Single Prism: 100 x 100 x 9 mm 

Detector, operating and control unit, 1 prism reflector 10 x 10 cm 

Reflector set for 761400 for ranges up to 80 m 

Reflector set for range extension consists of one acrylic glass plate for the mounting of up 

to 4 prism reflectors. 3 prism reflectors are already pre-mounted. The fourth is included in 

delivery of the Line Smoke Detector 761400. 



Dimensions (W x H) 294 x 294 mm 

Acrylic glass plate with three prism reflectors 

Reflector set for 761400 for ranges up to 100 m 

Reflector Set for range extension consists of one acrylic glass plate for the mounting of up 

to 9 prism reflectors. 8 prism reflectors are already pre-mounted. The ninth is included in 

delivery of the Line Smoke Detector 761400. 




Acrylic glass plate with eight prism reflectors


761403 

761404 

¬m/$-− 

Features 

• For easy ceiling and wall mounting in compliance 

with DIN VDE 0833-2 

• Optimal alignment of detector and reflectors 

under difficult environmental conditions via ball 

joint mounting bracket 

• Extendable ceiling bracket for flexible adjustment 

of length for distances of 400 to 700 mm 

• Invisible cable routing inside of the ceiling 

bracket 

761405 

761406 

761407 

¬m/%0− 

¬m/&3− 

¬m/'6− 

¬m/(9− 

Single reflector for LRMX 761400 

Replacement prism – single reflector for usage with the Line Smoke Detector 761400. 



Ceiling bracket for LRMX 761400 for distances 400 to 700 mm 

For better mounting of the Line Smoke Detector 761400 on walls, girders, ceilings and 

beams. The ceiling bracket is made of aluminium and can be adjusted in length anywhere 

from 400 to 700 mm. A high-grade ball joint mounting bracket is located on the top side for 

easy mounting. 

The ceiling bracket is suitable for attaching the Mounting Plate 761406. 

Ceiling bracket incl. mounting material for the aluminium holder but does not include material 

for mounting of the holder on ceilings, walls or beams. 

Ceiling bracket for LRMX 761400 for distances 700 to 1500 mm 

As 761404 but extendable for ceiling distances of 700 to 1500 mm. 

Mounting plate for ceiling bracket for detector/single reflector 

Mounting plate made of aluminium for attaching the Line Smoke Detector 761400 or the 

Prism Reflector 761403 on ceiling bracket. 

Mounting spider for Ceiling Bracket 761404 and 761405 

Mounting spider for the ceiling brackets 761404 and 761405 for alternativ attachment of the 

reflector sets 761401 and 761402 on the ceiling bracket. 

195 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

196 


Fireray 

761315 

Features 

• A compact housing 

• Maximum range 5 m to 50 m 

• Robust construction 

• Complies with EN 54-12 standard 

• Actuation and resetting is carried out via the 

esserbus transponder 808613.10 during loop 

operation 


¬m.0O− 

Fireray 50 RV, with one prism 

Approval: 

The detector consists of an infrared transmitter and receiver. The signal is reflected by a 

prism and analysed by the receiving element. Signal reaching the threshold will trigger an 

alarm. 

The actuation on the loop and the resetting function is carried out via the esserbus transponder 

808613.10. 


requires a separate voltage supply of 24 V DC. 

The Fireray is installed approx. 0.3 to 0.8m underneath the ceiling and its reflector with 

same ceiling distance opposite. There should be no reflecting obstacles in the transmission 

zone (approx. 2 degrees). 





Relays 1 x alarm NO switch potential-free, 

1 x trouble N/C contact potential-free 

Contact load max. 30 V DC / 1 A 




Type of protection lP 50 

Housing ABS plastic, flame resistant 


Weight 670 g 


Response sensivity 25%, 35%, 50% adjustable 



1 prism 761322 


VdS


761316 

Features 

• One compact housing 

• Maximum range 50 m to 100 m 

• Robust construction 

• Complies with EN 54-12 standard 



operation 

¬m.1R− 

Fireray 100 RV, with four prisms 

Approval: 


VdS 

The detector consists of the infrared transmitter and receiver. The signal is reflected by a 

prism and analysed by the receiving element. Signal reaching the threshold will trigger an 

alarm. 


808613.10. 



The Fireray is installed approx. 0.3 to 0.8m underneath the ceiling and its reflector with 

same ceiling distance opposite. There should be no reflecting obstacles in the transmission 

zone (approx. 2 degrees). 




Relays 1 x alarm NO switch potential-free, 

1 x trouble N/C contact potential-free 






Housing ABS plastic, flame resistant 


Weight 670 g 





4 prisms 761323 

197 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

198 


761321 

Features 

• Coverage: 10 to max. 100m 

• Width of monitored area: max. 13m (as per 

VdS) 

• Height of monitored area: max. 12m 

• Area to be monitored: max. 1300m 2 

• Automatic compensation for pollution and 

ageing by 15-step gain control 

• Rugged metal housing 

• Floating contacts for alarm and trouble 

• Test output for calibration and service 



operation 


¬m.6a− 

Fireray 2000 

Approval: 

Consisting of transmitter, receiver, and remote evaluation unit for light and dark smoke. 


808613.10. 




VdS 



Relays 1 x TROUBLE, potential-free changeover contact, 

1 x ALARM, potential-free changeover contact 

Contact load max. 30V DC / 1A 






Evaluating unit, housing sheet steel 

Colour evaluating unit grey, similar to RAL 7035 

Evaluating unit, dimensions (W x H xT) 210 x 265 x 85 mm 

Evaluating unit, weight 2140 g 



Dimensions (Ø x B x H) 60 x 102 x 95 mm (with angle) 

Range depends on the quantities of prism, see b.m. 

Weight for 540 g 

Detector specification prEN 54-12 

2 x mounting brackets, 4 x screws, 4 x grommets, 1 x test filter 

Application example


Accessories RETRO Mirror 

761322 

761323 

¬m.7d− 

¬m.8g− 

Reflector for use with the line type smoke detector when transmitter and receiver are 

installed together on one side of the monitoring area. (For planning information see Technical 

documentation of Fireray). 

1 prism for Fireray 


Range 5 to 25 m when Fireray 2000 and up to 50 m 

when Fireray 50 RV 

Dimensions (WxH) 100 x 100 mm 

4 prisms for Fireray 

The prisms are mounted on an aluminium mounting plate. 


Range 25 to 35 m when Fireray 2000 and up to 100 m 

when Fireray 100 RV 

Dimensions (WxH) 245 x 245 mm 

199 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

200 

Detectors for Special Applications Aspirating Smoke Detectors 

LRS-Loop Technology 


Please note that separate training is required for the LRS aspirating smoke detection system. 

As part of this training, further details are provided on project planning as well as commissioning. 

Required passwords are also given. 

For further information, please contact your local sales representative. 

Application example


801519 

Features 

• Fully integrated esserbus device 

• Programming and commissioning possible via 

the fire alarm control panel (System 8000 / 

IQ8(Control) 

• Direct transmission of all alarm messages, 

warning and fault messages to the control 

panel 

• Three alarm thresholds (information, pre- and 

main alarm) 

• Automatic learning function for determining 

optimum alarm threshold values (possible via 

the control panel) 

• Sensitivity range of 0.005% / m to 20% / m 

obscuration 

• Connection of an extraction pipe with a max. 

length of 80m (2 x 50m) 

• Voltage monitoring input for external power 

supply 

• One potential-free NO contact (contact load 

30V DC/1A) for main alarm 

• Filter and air flow monitoring for maintenance 

support 

• Event memory with up to 12,000 events 

• max. 8 LRS compact/EB per loop 

801519.GB0 

801519.F0 

801519.I0 

801519.E0 

¬q04c− 

¬q04§/HC1$− 

¬q04§/G1U− 

¬q04§/J1g− 

¬q04§/F1O− 

LRS compact/EB - Esser, German 

Approval: 


VdS, LPCB 

Active early-warning fire detection system for the esserbus, based on laser technology. 


Current consumption @ 24 V DC 225 mA to 245 mA 

Relays floating 




Temperature of the aspirated air -20° to +°60°C 


Relative humidity 10% to 95% without condensation 


Housing polycarbonate 


Weight 1.9 kg 


Programming via Editor, tools 8000 or VESDA software 

LRS compact/EB - Esser, English 

LRS compact/EB - Esser, French 

LRS compact/EB - Esser, Italian 

LRS compact/EB - Esser, Spanish 

201 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

202 


LRS Conventional Technology 

761519 

Features 


¬m04_− 

• Plug & play function (simple installation and 

commissioning) 

• Laser based smoke detection 

• Programmable alarm threshold value 

• Two-level air filtering 

• Integrated bargraph display 

• Integrated debugging function 


• Relay output: 3 changeover relays 



operation 

LaserFOCUS aspirating sytem - Esser, Multilingual 

Approval: 

Active detection system based on laser technology for the early detection of fires in small 

areas. 


808613.10. 




VdS 



Alarm current @ 24 V DC 295 mA 



Temperature of the aspirated air 0°C to 40°C 

Air humidity 5% to 95% (non-condensing) 

Maximum tube length 1 x 25 m (max. 12 vents) 2 x 15 m 

(max. 6 vents per duct arm) 

Detection area up to 250 m 2 

Weight approx. 2k g 



761500 

Features 

• Adjustable sensitivity from 0,005% / m up to 

20% / m obscuration 

• 4 programmable alarm levels (alarm, prealarm, 

fire 1, fire 2) 

• All alarm levels can be assigned to a time 

window from 0 - 60s to prevent false alarms 

• 2 fault levels (maintenance, fault) 

• 7 free configurable potential free contacts (30V 

DC / 1A) 

• Monitoring of filter and air flow to support service 

• Event memory up to 18,000 entries 

• Daily night operation (different sensitivity 

levels) 

• Connection of up to 4 pipes per detector unit 

with an overall length of up to 200m. It is possible 

to extend the overall length under consideration 

of the air transport time (100s according 

to the VdS) 

• Auto learn function to determine the best sensitivity 

level (the system stays armed during 

the self learning algorithm) 

• Programmable with tools LRS 200(761504) / 

210 (761505) or with a PC and the PC-interface 

LRS 300 (761506) and Windows© software 

797595 CD ROM with Software VConfig 

PRO and ASPIRE (these components are not 

supplied as standard) 

• It is possible to compensate the environmental 

conditions with a reference detector 

• Integration of up to 99 detector systems by the 

bus system “VESDAnet” 

• The alarm, fault and operation status is shown 

on the front panel 

• Pipe configuration with “ASPIRE” software , 

797595 CD ROM with Software VConfig PRO 

and ASPIRE 



operation 

762400 

762410 

762420 

762430 

¬m0!&− 

¬m9!8− 

¬m9+V− 

¬m95t− 

¬m9?+− 

Aspirating smoke detector unit LRS 100 - Esser, German 

Approval: 


VdS 

Early fire detection system based on laser technology. The system is optimised for use in 

the following areas: air conditioned areas (e.g. data processing rooms), laboratories and 

clean rooms, rooms with valuable things (e.g. museum). Connection via a 781332 reset 

module (System 8000 / IQ8Control) and with additional 24V supply voltage. 


808613.10. 




Current consumption 240 mA to 500 mA 



Connection terminal 0.2 to 2.5 mm 2 

Temperature of the aspirated air -20°C to +60°C 


Weight 3.5 kg 

Colour grey 

Housing metal 


LRS 100 aspirating smoke detector - Esser, English 

LRS 100 aspirating smoke detector - Esser, French 

LRS 100 aspirating smoke detector - Esser, Italian 

LRS 100 aspirating smoke detector - Esser, Spanish 

203 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

204 


761502 

762403 

762413 

762423 

762433 


¬m0#,− 

¬m9$A− 

¬m9._− 

¬m98}− 

¬m9B4− 

Detector unit LRS-S 700 - Esser, German 

Approval: 

VdS 

As detector unit LRS 100 (761500) but with integrated scanner module and 12 x relay 

board. Enabling the unit to analyse up to 4 pipes separately. Four different areas can be 

monitored. This unit has 12 configurable potential-free contacts (10 NO contacts, 2 changeover 

contacts), instead of 7 in the LRS 100. 

LRS-S 700 aspirating smoke detector - Esser, English 

LRS-S 700 aspirating smoke detector - Esser, French 

LRS-S 700 aspirating smoke detector - Esser, Italian 

LRS-S 700 aspirating smoke detector - Esser, Spanish


761515 

Features 

• Adjustable sensitivity from 0,005% / m up to 

20% / m obscuration 

• 3 programmable alarm thresholds (alarm, pre 

alarm, main alarm). 

• For an increased protection from false alarms, 

all alarm thresholds can be given a time 

window of 0 – 60 sec 

• 2 fault levels (maintenance, fault) 

• 3 potential-free contacts (switching capacity 

30V DC / 2A) consisting of 1 potential-free 

changeover contact and 2 potential-free switching 

contacts 

• Filter and air stream monitoring for easier 

maintenance 


• For use with an extraction tube with a total 

length of max. 80m (2 x 50m) 

• Automatic learning function for determining 

optimum sensitivity level (the units remain 

operative during this learning phase) 

• Adjustments can be made by means of a PC in 

combination with 797595 CD ROM with Software 

VConfig PRO and ASPIRE Windows software 

and a standard interface cable w/o interface 

(modules are not supplied as standard) 

• Main alarm, pre alarm, trouble and operation 

status are indicated on the front panel 

• ”ASPIRE” , 797595 CD ROM with Software 

VConfig PRO and ASPIRE PC software for 

extraction tube 



operation 

762406 

762407 

762416 

762426 

762436 

¬m00S− 

¬m9'J− 

¬m9(M− 

¬m91h− 

¬m9;¨− 

¬m9E=− 

LRS compact - Esser, German 

Approval: 


VdS 

Active early fire detection system using laser technology. 


808613.10. 




Current consumption 170 mA to 190 mA 


Temperature of the aspirated air -20°C to +60°C 


Connection terminal 0.2 to 2.5 mm 2 

Weight 1.9 kg 


Housing polycarbonate 



LRS compact aspirating system - Esser, English 

LRS compact / net aspirating system - Esser, English 

LRS compact aspirating system - Esser, French 

LRS compact aspirating system - Esser, Italian 

LRS compact aspirating system - Esser, Spanish 

205 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

206 


761516 

Features 

• Adjustment by means of programming unit 

LRS 200 (761504) / 210 (761505) or PC with 

PC interface LRS 300 (761506) and 797595 

CD ROM with Software VConfig PRO and 

ASPIRE Windows software (modules are not 

supplied as standard) 

• The environmental conditions may be compensated 

by using an additional reference detector 

• Integration of up to 99 detector units via the 

proprietary “VESDAnet” bus system 

• Indicating and operating panel can be connected 

via the VESDAnet (761501, 761507) 

762417 

762427 

762437 

Accessories 

761501 


¬m01V− 

¬m92k− 

¬m9


762401 

762411 

762421 

762431 

761507 

762402 

762412 

762422 

762432 

¬m9";− 

¬m9,Y− 

¬m96w− 

¬m9@.− 

¬m0(;− 

¬m9#>− 

¬m9-\− 

¬m97z− 

¬m9A1− 

Indicator and operating module LRS 110 - Esser, English 

As 761501, but Esser - English 

Indicator and operating module LRS 110 - Esser, French 

As 761501, but Esser - French 

Indicator and operating module LRS 110 - Esser, Italian 

As 761501, but - Esser, Italian 

Indicator and operating module LRS 110 - Esser, Spanish 

As 761501, but - Esser, Spanish 

Indicator and operating module LRS-120 - Esser, German 

Approval: 

VdS 

As 761501 but without relays. 


Indicator and operating module LRS-120 - Esser, English 

As 761507 but Esser - English 


Indicator and operating module LRS-120 - Esser, French 

As 761507, but - Esser, French 


Indicator and operating module LRS-120 - Esser, Italian 



Indicator and operating module LRS-120 - Esser, Spanish 



207 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

208 


761503 

762404 

762414 

762424 

762434 

761508 

762405 

762415 

762425 

762435 


¬m0$/− 

¬m9%D− 

¬m9/b− 

¬m99¢− 

¬m9C7− 

¬m0)>− 

¬m9&G− 

¬m90e− 

¬m9:¥− 

¬m9D:− 

Indicator and operating module LRS-S 710 - Esser, German 

Approval: 

VdS 

As 761501 but for LRS-S 700 (761502) detector unit. 


Indicator and operating module LRS-S710 - Esser, English 

As 761503, but - Esser, English 

Indicator and operating module LRS-S710 - Esser, French 


Indicator and operating module LRS-S710 - Esser, Italian 


Indicator and operating module LRS-S710 - Esser, Spanish 


Indicator and operating module LRS-S 720 - Esser, German 

Approval: 

VdS 

As 761503 but without relays. 


Indicator and operating module LRS-S720 - Esser, English 

As 761508, but - Esser, English 


Indicator and operating module LRS-S720 - Esser, French 



Indicator and operating module LRS-S720 - Esser, Italian 

As 761508, but - ESSER, Italian 


Indicator and operating module LRS-S720 - Esser, Spanish 




761504 

761505 

761517 

761506 

¬m0%2− 

¬m0&5− 

¬m02Y− 

¬m0'8− 

LRS 200 LCD-Programmer for aspirating system 

Handheld programming unit. All components in the VESDAnet can be programmed. Easy 

programming with a LCD graphical user interface. The system has to be connected to the 

BUS system to program the components. 


Current consumption 20mA to 80mA 

The connection cable is included. 


LRS 210 LCD-Programmer for aspirating system 

As LRS 200 (761504) programming unit but in a surface mount housing. This unit is continuously 

connected to the bus system and allows fast access to all components. 



Housing metal 

For flush mounting, please order kit no. 761511 separately. 


VESDAnet connection box 

This connection box enables external devices to be connected to the VESDANet. For 

example, a handheld programmer or a PC can be connected in conjunction with the PC 

interface to program the system. 

The LRS 300 PC-Interface (761506) is also required. 

LRS 300 PC-Interface 

Used as an alternative to the programming unit. All components on the VESDAnet can be 

programmed via the interface. 


Operating voltage VESDAnet supplied 

Current consumption 70mA 


The two required connectors are included. 

209 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

210 


761510 

761511 

761512 

761518 

797595 


¬m0+D− 

¬m0,G− 

¬m0-J− 

¬m03\− 

¬pl¢"− 

Flush mounting kit for LRS 100 and 700 detectors 

Flush mounting kit for the detectors LRS 100 (761500) and LRS-S 700 (761502). 


Mounting frame 40mm surrounding entire frame 


Flush mounting kit for LRS 210, 110, 120, 710, 720 control panels 

Flush mounting kit for LRS 210 (761505) programming unit and for LRS 110 (761501), 

LRS 120 (761507), LRS-S 710 (761503) und LRS-S 720 (761508) indicating and operating 

units. 


Mounting frame 40mm (surrounding entire frame) 


Spare filter for VESDA aspirating smoke systems 

For detector units LRS 100 (761500) / LRS S700 (761502) / LRS compact (761515)/ LRS 

compact / net (761516)/ LRS compact/EB(801519)/Laser Focus (761519). 

VSM3 software - basic system 

VSM3 software is a comprehensive management software package which continuously 

shows status of all the devices in the network. All alarm and fault messages and smoke 

trends are displayed online. 

The software package can equally be used for commissioning all devices in the entire network 

from a central point. 

For the assignment of the release code please contact our responsible sales representative or 

sales office. 


CD ROM with software VConfig PRO and ASPIRE 

CD ROM with programming software VConfig PRO and planning software ASPIRE, system 

presentations, reference projects, tender texts and documentation. For use under Windows® 

9X, 2000. 



Titanus EB aspirating smoke detection 

Features The Titanus EB aspirating smoke detection system is suitable for active early fire detection. 

Highest application flexibility through modular 

design 

• Direct connection to the esserbus/esserbus-Plus 

(powered loop) 

• Easy commissioning through pre-set system configuration 

at delivery 

• Parameters for response sensitivity can be configured 

at the detector module 

• Up to 180m duct length per duct 

• Up to 24 suction vents 

• Two-detector dependency can be set up in compliance 

with VdS guidelines 

• Parallel detector indicator (part no 801824) can 

be connected 

Fires are detected via a modular detector module. Through HPLS technology (High-Power- 

Light-Source), the Titanus EB offers high detection quality as well as constant and reliable 

response features in case of fire. 

On account of its modular design, the detector modules provide a high degree of flexibility 

in planning and installation for aspirating smoke detection systems. 

Easy and cost-saving upgrades of already existing systems can be easily performed, since 

each Titanus EB system can integrate a maximum of two detector modules. By using only 

two detector modules, the detection area can be extended at a minimum expense. 

Through physically separated detection chambers and independent evaluation of aerosols 

aspirated via air ducts, two-detector dependency can be set up in compliance with VdS 

regulations. 

The detector modules for the Titanus EB System Pro Sens and Top Sens are available with 

three different sensitivity levels. Thus, various applications ranging from early fire detection 

purposes to earliest fire detection purposes with raised sensitivity levels can be tackled. 

The Titanus Pro Sens EB is an aspirating smoke detection system suitable for universal 

application ranges with different requirements to detection sensitivity. The Titanus Top Sens 

EB aspirating smoke detection system is the expanded version and is provided with 3 alarm 

levels („info alarm“, pre-alarm“ and „main alarm“) as well as with integrated smoke level 

display (bargraph). 


211 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

212 


801515 

Features 


¬q00W− 

• Fire and fault indication directly at the unit and 

at the fire alarm control panel 

• Fast commissioning through automatic initialising 

process and plug & play operation 

• Air flow monitoring for detecting pipe burst or 

tube blocking 

• Protection against disturbances when implemented 

LOGIC SENS function is activated 

• Integrated and pre-configured detector module 

(Part No. 801523) 

Compact unit Titanus Pro Sens EB 

Approval: 

Active system for the early detection of fires. It serves as room and furnishing protection 

and can be directly connected to the esserbus / powered loop. The compact aspirating 

smoke detection system Titanus Pro Sens EB is completely supplied with detector module 

DM-TP-80. Plug & Play operation for fast and simple commissioning through pre-programmed 

standard functions and pre-configured detector modules. 


VdS 


Exhauster voltage 6.9 V or 9 V 

Starting current @ 24V DC (w/o reset PCB) 300 mA 

Quiescent current @ 24V DC (w/o reset PCB) from 200 mA up to 275 mA 

Alarm current @ 24V DC (w/o reset PCB) from 210 mA up to 285 mA 

Current consumption of the reset PCB max. 20 mA 

Switching capacity of alarm and trouble relay 30 V DC/1A max. 24 W 



Switching capacity level LWA as per 

EN 27779, 1991 approx. 45 dB(A) (with sound absorber 

Part No. 801543) 


Housing Material ABS plastic 

Housing colour white, similar to RAL 9018 



Air humidity max. 95% rel. humidity, w/o condensation 

Exhauster design redial 

Exhauster life time (12V) 43,500 h at 24°C 

LED-Display 

Alarm red LED 

Collective fault yellow LED 

Start green LED 

Connection terminal max. 1.5 mm 2 

Connecting cable (recommended) pair-wired, screened 

e.g. I-Y(St)Y n x 2 x 0.8 mm 

Cable feedthrough 5 x M 20 / 2 x M 25 

Beveled tubular plug 1 x for ABS tube D=25mm for return air duct 

D=25 mm 

Isolator not included with delivery, can be optionally ordered under Part No. 788612. 

Pre-configured Titanus Pro Sens EB basic device including esserbus transponder and reset PC 

board as well as the Titanus Pro Sens EB front foil and pre-configured detector module DM-TP- 

80.


801521 

Features 

¬q06i− 

• pre-configured for connecting a detector 

module DM-TP-xx 

• optical status display for alarm and fault indication 

at the front foil 

• extendable for integrating up to two detector 

modules DM-TP-xx to connect a second tube 

• ports for two suction tubes with an outside diameter 

of 25mm 

• port for air return tube 

Basic unit Titanus Pro Sens EB 

Approval: 


VdS 

Basic unit for wall mounting, ready for receiving a detector module DM-TP-xx. 

The Titanus Pro Sens EB can be directly connected to the esserbus / powered loop. 

The device is supplied with front foil for single-tube operation. 












Part No. 801543) 









LED-Display 




Connection terminal max. 1.5mm 2 




Beveled tubular plug 1 x for ABS tube D=25 mm for return air duct 

D=25 mm 


Pre-configured basic device Titanus Pro Sens 1 EB including an esserbus transponder, a reset 

PCB and the front foil Titanus Pro Sens EB. 

213 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

214 


801522 

Features 


¬q07l− 

• pre-configured for integrating up to two 

detector modules DM-TP-xx to connect two 

tubes 

• optical status display for alarm and fault indication 

at the front foil 


of 25mm 


• possible two-detection-dependency as per VdS 

directive 

Basic unit Titanus Pro Sens 2 EB 

Approval: 

Basic unit for wall mounting, ready for receiving up to two detector modules DM-TP-xx. 

The Titanus Pro Sens 2 EB can be directly connected to the esserbus / powered loop. 

The device is supplied with front foil for two-tube operation. 


VdS 











EN 27779, 1991 approx. 45 dB(A) (sound absorber 

Part No. 801543) 









LED-Display 




Connection terminal max. 1.5 mm 2 





D=25 mm 


Pre-configured basic device Titanus Pro Sens 2 EB including an esserbus transponder, a reset 

PCB and the front foil Titanus Pro Sens 2 EB.


801531 

Features 

¬q0@©− 

• pre-configured for connecting a detector 

module DM-TT-xx 

• optical status display for information alarm, 

pre-alarm, main alarm and fault indication at 

the front foil 

• extendable for integrating up to two detector 

modules DM-TT-xx to connect a second tube 

• integrated bargraph display to optically indicate 

the current smoke level 


of 25mm 



directive 

Basic unit Titanus Top Sens EB 

Approval: 


VdS 

Basic unit for wall mounting, ready for receiving a detector module DM-TT-xx. 

It is provided with three alarm levels for information alarm, pre-alarm and main alarm as 

well as with a bargraph display to indicate the specific smoke density. 

The Titanus Pro Sens EB can be directly connected to the esserbus / powered loop. 

The device is supplied with front foil for single-tube operation. 


Exhauster voltage 6,9 V or 9 V 


Quiescent current @ 24V DC (w/o reset PCB) 200 mA to 260 mA 

Alarm current @ 24V DC (w/o reset PCB) 230 mA to 290 mA 

Current consumption of the resre PCB max. 20 mA 

Switching capacity of alarm and trouble relay 30 V DC/1 A max. 24 W 


Weight 1,35 kg 


EN 27779, 1991 ca. 45 dB(A) (with sound absorber 

Part No. 801543) 







Exhauster life time (12V) 43.500 h at 24°C 

LED-Display 

Alarm 2 red LED 





e.g. I-Y(St)Y n x 2 x 0,8 mm 



D=25 mm 


Pre-configured basic unit Titanus Top Sens EB including esserbus transponder, reset PCB and 

front foil Titanus Top Sens 1 EB. 

215 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

216 


801532 

Features 


¬q0A#− 

• pre-configured for usage with two DM-TT-xx 

detector modules 

• optical status display for information alarm, 

pre-alarm, main alarm and fault indication 

• integrated bar graph display to optically indicate 

the current smoke level 


of 25mm 



directive 

Basic unit Titanus Top Sens 2 without module 

Approval: 

Basic device for wall mounting, pre-configured to receive up to two DM-TT-xx detector 

modules. 

The Titanus top Sens 2 EB is directly connectable to the esserbus/ esserbus-PLus. The 

device is shipped equipped with the front foil for the double tube operation. 


VdS 


Exhauster voltage 6,9 V or 9 V 


Quiescent current @ 24V DC (w/o reset PCB) 200 mA to 275 mA 

Alarm current @ 24V DC (w/o reset PCB) 210 mA to 285 mA 


Switching capacity of alarm and trouble relay 30 V DC/1 A max. 24 W 




Part No. 801543) 






Air humidity max. 95% rel. humidity (without condensation) 


Exhauster life time (12V) 43.500 h at 24°C 

LED-Display 









D=25 mm 



Pre-configured Titanus Top Sens 2 EB basic device contains 2 esserbus transponders, two reset 

PC boards and the Titanus Top Sens 2 EB front foil. 

Detector modul for Titanus Pro Sens EB aspirating smoke detection 

801523 

Features 

¬q08o− 

• Response sensitivity adjustable at the module 

• Fast commissioning through automatic initialising 

process 

• Status display for status and fault diagnosis 

• Installation into Titanus Pro Sens EB without 

tools 

• Air flow monitoring for detecting pipe burst 

and tube blockage 

Detector module 0.8%/m DM-TP-80 

Detector module for application in Titanus Pro Sens EB aspirating smoke detection systems 

(Part Nos. 801515, 801521, 801522) with a response sensitivity of 0.8% light opacity / m. 

Early fire detection via HPLS technology. Installation into Titanus Pro Sens EB systems 

without tools and adjustable via DIL switch on the outside of the detector module. The parameterisation 

option allows sensitivity adjustments for the aspirating smoke detection 

system. 



Weight 100g 

Housing Material ABS plastic


801524 

801525 

¬q09r− 

¬q0:u− 


As 801523 but with raised response sensitivity of 0.25% light opacity / m. 


As 801524 but with raised response sensitivity of 0.05% light opacity / m. 

Detector module for Titanus Top Sens EB aspirating smoke detection 

801533 

801534 

801535 

Accessories 

801540 

¬q0B&− 

¬q0C)− 

¬q0D,− 

¬q0I;− 

Detector module 0.8%/m DM-TT-80 

Detector module for application in Titanus Top Sens aspirating smoke detection systems 

(Part Nos. 801531, 801532) with a response sensitivity of 0.8% light opacity / m. 

Early fire detection via HPLS technology. Installation into Titanus Top Sens EB systems 

without using any tools and adjustable via DIL switch on the outside of the detector module. 

The parameter setting option allows sensitivity adjustments for the aspirating smoke detection 

system. 



Weight 100g 



As 801533 but with a raised response sensitivity of 0.25% light opacity / m. 


As 801534 but with a raised response sensitivity of 0.05% light opacity / m. 

Device holder for aspirating smoke detection systems Titanus EB 

Device holder for mounting aspirating smoke detection systems to frames or for self-supporting 

mounting. 


Weight 1160g 

Dimensions (L x W) 432 x 92mm 

217 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

218 


801541 

801542 

801543 

801547 


¬q0J>− 

¬q0KA− 

¬q0LD− 

¬q0PP− 

Reset PCB for Titanus EB 

PCB for resetting the Titanus Pro Sens EB and the Titanus Top Sens EB aspirating smoke 

detection system via the fire alarm control panel. 


Current consumption 5 to 50mA 

Dimensions (L x W) 57 x 45mm 

Back-flow valve for Titanus EB 

Valve for cleaning the tubing system through air purging via compressed air. In systems 

with air purging, the non-return valve is mounted at the end of the tubing branch and prevents 

a build-up of dirt particles at the end of the tube. 

Sound absorber for Titanus EB aspirating smoke detection systems 

Sound absorber for redusing sound levels in Titanus EB aspirating smoke detection systems 

for sound-sensitive applications. The sound absorber is connected to the tube outlet and 

reduces the sound level during operation by up to 10 dB(A). 

Installation either directly at the air release or with 10cm maximum distance from the air 

release. 



Colour RAL 7035 

Weight 454g 


Front foil Titanus Pro Sens 2 EB 

Front foil for indicating alarms when using two detector modules


801548 

801549 

¬q0QS− 

¬q0RV− 

Front foil Titanus Top Sens 2 EB 

Front foil for indicating staged alarm modes and smoke density levels when using two 

detector modules. 

Diagnostics tool for Titanus EB 

Diagnostics tool for Titanus EB aspirating smoke detector systems for reading the measurement 

data and device configurations as well as for localization of faults. 

Diagnostics interface, connecting cable and diagnostic software 

ARS 70 Analog Line Type Aspirating Smoke Detection System 

761345 

Features 

¬m.NB− 

• For direct esserbus connection 

• Detection chamber prepared for installing the 

801372 smoke detector 

• Electronic evaluation unit 

• Optical signalling for detector 1, detector 2, 

fault and operation 

• Automatic monitoring of the air stream for breakage 

and blockage of the extraction pipes 

• Potential-free changeover contacts for alarm 1, 

2 and trouble 

• Built-in high performance fan 

• Max. 20 suctions points 

• Max. suction point distance: 100m 

ARS 70-1 analog line type aspirating smoke detection system 

Approval: 

VdS 

For room surveillance, air samples are continuously extracted via pipes and led to a smoke 

detector. 





Contact load 30 V DC / 1A 

Ambient temperature 0°C to + 50°C (housing) 

Storage temperature -5°C to +55°C (housing) 

Relative humidity < 95 % for a short time without condensation, 

< 70 % permanently 



Colour grey/anthracite 



The system is also suitable for powered loop. 

A detector base and an esserbus transponder are included. The detector is not included and 

must be ordered separately. 


Only available until 30.09.2009! 

219 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

220 


761346 

801372 

801372.SV082.N4 


¬m.OE− 

¬q.i0− 

¬q.i§/TW193/O5u− 

ARS 70-2 aspirating smoke detection system for two detectors 

Approval: 

VdS 

As 761345, but for room surveillance, with air samples being led to two detectors 

(2-detector dependency possible). 

The system is also suitable for powered loop. 

Two-detector dependency for extinguishing system is not approved by VdS. Please use detector 

box 761545. 

The system includes two detector bases and one esserbus transponder. The detectors are not 

included and must be ordered separately. 



Optical smoke detector for ARS 70 

Approval: 

Intelligent smoke detector for use in the ARS 70 aspirating smoke detection system 

(761345 / 761346). 



VdS in combination with ARS 70 

Optical smoke detector for ARS 70 - ELTEK 

Accessories for Aspiration Smoke System 

761520 

761521 

¬m05b− 

¬m06e− 

Intelligent smoke detector for use in the ARS 70 aspirating smoke detection system 

(761345 / 761346). Special version PCB double coated and ELTEK branded. 


Pipe (PVC), diameter 25mm 

Length = 5m 

The price stated is the unit price for a 5m pipe. Temperature range: -40°C to +60°C. 

on demand 

90° bend (PVC) for 25mm pipe


060865 

761522 

761523 

761524 

761525 

¬')b.− 

¬m07h− 

¬m08k− 

¬m09n− 

¬m0:q− 

Cross piece for 25mm pipe 

90° angle (PVC) for 25mm pipe 

45° angle (PVC) for 25mm pipe 

T-Piece (PVC) for 25mm pipe 

Sleeve (PVC) for 25mm pipe 

221 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

222 


761526 

761527 

761528 

761529 


¬m0;t− 

¬m0}− 

End cap (PVC) for 25mm pipe 

Vent (PVC) for 25mm pipe 


Outside diameter 36.0mm 

Inner diameter 21.5mm 

Hose with textile insertion (PVC) for 25mm pipe 

The price stated is price per metre. 

Flange for climate channel (PVC) for 25mm pipe 

Monitoring of air duct


761531 

761530 

761534 

¬m0@¥− 

¬m0?¢− 

¬m0C%− 

Small funnel (polypropylen) for 25mm pipe 

Application example, see drawing under Part No. 761529. 

3-way-sphere tap (PVC) for 25mm pipe 

For connecting compressed air, in order to blow out the pipework. 

Principle of water trap 

Separator for 25mm pipe 

For application in a high humidity environment. Plastic housing, grey, including connection 

to the pipe. 



Principle of water trap 

223 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

224 


761532 

761533 

761535 

761536 

761537 


¬m0A¨− 

¬m0B"− 

¬m0D(− 

¬m0E+− 

¬m0F.− 

Filter chamber for 25mm pipe 

For application in dusty environments. Plastic housing, grey, including three installed filters 

and two fittings for the pipe. 



Application example, see drawing under Part No. 761534 and 761530. 

Spare filter for filter chamber 761532 

For filter chamber 761532. 

PVC adhesive, 0.5kg can 

Adhesive for connecting PVC pipes and fittings. 

PVC detergente, 1l can 

Detergente for cleaning PVC pipes and fittings before glueing. 

Mounting clip IKS for 25mm pipe


761542 

761543 

761544 

¬m0K=− 

¬m0L@− 

¬m0MC− 

Suctions hose set for 25mm pipe 

For flexible installation in object surveillance or suspended ceilings. 


Material PVC 

Diameter 25 mm (port) 

Length max. 3 m (corrugated polyester hose) 

All components are pre-mounted and glued. 

1 x T piece (761524), 3m corrugated polyester hose, (761543), 1 x ceiling lead-through adapter 

with threaded joint 

Monitoring of room 

Corrugated polyester hose 

The price stated is the price per metre. 

Threaded joint, detachable, 25mm 

225 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

226 


761546 

761547 

801550 


¬m0OI− 

¬m0PL− 

¬q0SY− 

Pipe cutter for PVC / ABS pipes 

Sturdy aluminium design. Replaceable, specially hardened blade. For single-hand operation. 

Effortless working through power transmitting ratchet feed. Quick reverse saves time and 

effort. Right angle, burr-free cut through exact pipe support and guided blade on both sides. 

Chipless cutting – no chips remaining in pipe. 

Pipe cutter for plastic pipes 6-35 mm 


Labels-Sampling Points Wrap Round 

The Labels-Sampling Points Wrap Round serves for the marking of the intake points of the 

PVC/ABS pipe. 

Please note the Labels-Sampling Points Wrap Round are not use for tapering the intake points. 

Roll with 200 labels. 

Banderole for suction-reducing foil 

Banderole for securing the suction-reducing foils on the tubing system. The red marking is 

used for the localization of the detector points in the object. 

10 pieces


Aspiration reducing films 

801551 

801552 

801553 

801554 

801555 

801556 

801557 

801558 

801559 

801560 

801561 

801562 

801563 

801564 

801565 

801566 

801567 

¬q0T\− 

¬q0U_− 

¬q0Vb− 

¬q0We− 

¬q0Xh− 

¬q0Yk− 

¬q0Zn− 

¬q0[q− 

¬q0\t− 

¬q0]w− 

¬q0^z− 

¬q0_}− 

¬q0`¢− 

¬q0a¥− 

¬q0b¨− 

¬q0c"− 

¬q0d%− 

Aspiration reducing film sheet for defined smoke-extraction openings. The foils are for tapering 

the drill holes in the intake manifolds and prevent any increased development of noise 

in the operation of the aspirating smoke detection system. The diameter of the smoke 

extraction opening is printed on the smoke extraction reduction foil. 

For uniform detection across all smoke extraction openings, the opening diameters should 

be selected according to the specifications in the function description. 

10 pcs 

Aspiration reducing film sheet 2,0 mm 

















227 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

228 

Detectors for Special Applications Accessories 

781332 

781332.F0 

781333 


¬o.A¦− Reset module for C-rail mounting 

Module for connecting a third-party detector (with floating relay contact for alarm and fault) 

on a conventional primary loop. Remote reset function can be controlled via the relay contact 

on the reset module. Total power consumption depends on the detectors that are connected. 

The following detector types can be connected: high sensitivity aspirating smoke 

detection system, flame detectors, Fireray, line type heat and smoke detectors etc. 


Zone voltage 8V DC to 24V DC 

External voltage 10.5V DC or 28V DC 

Contact load relay 30V DC / 1A 

Current consumption out of the detector zone approx. 0.5mA 

Current consumption @ 12 V DC approx. 1mA - relay non-energised, 

35mA - relay energised 

Current consumption @ 24 V DC approx. 10mA - relay non-energised, 

55mA - relay energised 

Reset time adjustable via bridges approx. 150ms to approx. 17s 

Dimensions PCB (W x H x D) 37 x 107 x 13mm 

Version: Module housing for C-rail mounting. 

¬o.A§/G1v− Reset module for C-rail mounting - Esser, France 

¬o.B©− 

as 781332 but with French labels. 

Reset module with mounting bracket for Fireray 2000 

Reset module as in 781332 including mounting accessories for installation in Fireray 2000 

evaluation unit (Part No. 761321). 

Reset module including bracket and mounting material.

Alarm devices IQ8Alarm 230 - 236 


Remote Indicators 244 - 246 

229 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

230 

Alarm Devices IQ8Alarm 

IQ8Alarm enables IQ8Quad detector application with integrated alarm signalling and other advantages. No matter whether multilingual speech 

alarm, flexible signal combination or user-friendly programming interfaces, all these features are also available when using IQ8Alarm. 

The IQ8Alarm range offers distinct advantages, which will surely convince every user in the blink of an eye. 

Advantages with IQ8Alarm at one glance: 

• Simple programming enabled by a standardised programming interface for 

all IQ8Systems (IQ8Quad + IQ8Alarm) alarm signalling devices 

• Voltage supply on the loop 

• Time-tested, unobtrusive design 

• Signalling device in compliance with EN 54 with 20 different signalling tones 

including DIN tone in compliance with DIN 33404-3 

On the following pages, you will find more detailed information about IQ8Alarm features. 



Features 

• Completely bus supplied alarm device 

• Powered loop compatible 

• 5 different signalling device types 

- acoustic 

- optical 

- acoustic / optical 

- acoustic / optical 

- acoustic / optical / speech 

• Multilingual speech alarm in 5 different languages 

• Alarm signalling, evacuation, and test alarm can 

be respectively programmed in different languages 

• Up to 32 alarm devices for each powered loop 

• Each alarm device with built-in isolator 

Acoustic alarm signalling: 

• Acoustic pressure up to 99 dB(A) @ 1 m 

• Volume programmable in 8 steps via tools 8000 

• 20 different signalling tones, including DIN tone 

• Speech alarm, 5 pre-programmed alarm texts and 

other country-typical alarm signals 

Optical alarm signalling: 

• Flash intensity equivalent to 3W Xenon flash light 

• Light intensity: max. 3.87cd effective, max. 24cd 

peak 

IQ8Alarm alarm signalling devices represent a more sophisticated version replacing our 

powered loop products. On the whole, there are 5 different alarm signalling product groups: 

- sounders 

- speech alarm 

- alarm devices with combined acoustic and optical alarm signalling 

- alarm devices with combined acoustic and optical alarm signalling with speech alarm 

- optical alarm signalling devices 

How to define the maximum number of alarm signalling devices foe connection to the same 

primary loop: 

In case of mixed operation of various alarm signalling types and bases connected to the 

same primary loop, the maximum number depends on the loop length. Each individual load 

factor must be added up, since the load factor defines the respective current consumption 

for each alarm device during alarm. 

For IQ8Alarm application, the load factor depends on the alarm device type (see technical 

data). 

Please consider our examples and tables shown in the „Project Planning Support“ section. 

The total load factor for one primary loop is not permitted to exceed the maximum value of 

96. Altogether up to 127 bus devices per loop can still be connected. 


Operating voltage 8 to 42 V DC (esserbus-PLus) 



Load factor 3 

Sound pressure @ 90° DIN = typ. 97 dB(A) +/- 2 dB @ 1m 

Lightning energy approx. 3 J 

Strength of light max. 24cd peak/ 3,87 cd effctive 

Frequency of flash 1 Hz 

Ambient temperature -10°C to + 50°C 


(IP 65 with socket 806201 / 806202) 


Housing ABS 

Dimensions (ØxD) 112 x 75 mm 

IQ8Control with powered loop functionality. 

The system can only be programmed when using the tools 8000 editor. 

Please consider: 

- admissible maximum loop length 

- admissible maximum number of single alarm device types 

- maximum number of 127 bus devices for each loop 

Systems requirements: 

FACP IQ8Control Version 3.04 with the programming software tools 8000 Version 1.09 ! 

Attention - an operation with the FACP’S 8000 C/M is not possible !!! 

For upgrading 8000 C/M control units, IQ8Lumivox signalling devices must be used. If required, 

please contact our returns department. 

For checking the battery capacity of fire alarm control units, the value „quiescent current @ 

FACP battery“ can be added. 

231 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

232 



List of the standard for each of those language 

IQ8Quad/IQ8Alarm tone table


807205 

807206 

807322 

807332 

¬qi&D− 

¬qi'G− 

¬qj7y− 

¬qjA0− 

IQ8Alarm sounder, white 

Approval: 


VdS 

Addressable, completely bus supplied and short circuit / open circuit resilient alarm signalling 

device in compliance with EN 54-3 with up to 20 different programmable signalling 

tones including DIN tone in accordance with DIN 33404 Part 3 for acoustic alarm signalling. 

The volume can be set to 8 different levels. Its flat design enables optimum adaptation to 

the environments. It is made of shock and scratch resistant plastic. Optionally, bases 

806201 and 806202 with side cable entry and weatherproof protection can be installed. 

Quiescent current @ 19 V DC 55μA 

Quiescent current @ FACP battery 300μA 

Load factor 3 

Sound pressure max. 99dB(A) 



IQ8Alarm sounder, red 

Approval: 


VdS 

As in 807205, but red 


IQ8Alarm speech alarm, white 

Approval: 


VdS 

As in 807205, but with additional speech alarm function. 



Load factor 3 




IQ8Alarm speech alarm, red 

Approval: 


VdS 



233 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

234 


IQ8Alarm combined alarm and speech signalling device 

807224 

807372 

807372.SV98 

807372.SV99 


¬qi9}− 

¬qjiA− 

¬qji§/TW:9Z− 

¬qji§/TW::c− 

IQ8Alarm combined alarm signalling device 

Approval: 


device in compliance with EN 54-3 with up to 20 different programmable signalling 

tones including DIN tone in accordance with DIN 33404 Part 3 for acoustic and optical alarm 

signalling. The volume can be set to 8 different levels. Its flat design enables optimum adaptation 

to the environments. It is made of shock and scratch resistant plastic. Optionally, 

bases 806201 and 806202 with side cable entry and weatherproof protection (IP65) can be 

installed. 


VdS 



Load factor 3 



IQ8Alarm combined speech alarm 

Approval: 

As in 807224, but with programmed speech alarm for powered loop connection. 


VdS 



Load factor 3 




IQ8Alarm combined speech alarm with composition of other languages 

Approval: 

VdS 

As with 807372, but with an individual combination of national languages. 

When ordering, please note the “Ordering information for IQ8Quad and IQ8Alarm alarm signaling 

devices” printed in the appendix. 

Please take not that no cancellations or returns accepted. 

Programmed with an individual combination of up to 5 national languages. 

IQ8Alarm combined speech alarm as customized version 

Approval: 

VdS 

As 807372, but with individual texts and/or sounds. 

To order, please use the enclosed “Order form for custom languages”. 

Costs for the recording of customer-specific texts and/or tones can be obtained by request. 

Please take not that no cancellations or returns accepted. 

Programmed in accordance with customized combination.


IQ8Alarm optical alarm signalling devices 

807212 

807213 

807214 

¬qi-Y− 

¬qi.\− 

¬qi/_− 

IQ8Alarm optical alarm signalling device, amber 

Approval: 


VdS 


device for optical alarm signalling. Its flat and unobtrusive design enables optimum 

adaptation to the environments. 

Load factor 3 

Strength of light max. 24cd peak / 3.87cd effective 

Flash rate 1Hz 

Colour base: white, similar to RAL 9010 

cap: amber 

IQ8Alarm optical alarm signalling device / tranparent, blue, green 

Approval: 


VdS 

As in 807212, but transparent, blue and green. 

Colour base: white, similar to RAL 9010; 

cap: transparent, blue and green 

IQ8Alarm optical alarm signalling device, red 

Approval: 


VdS 


Colour base: red, similar to RAL 3020 

cap: red 

235 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

236 


Accessories 

806201 

806202 


¬q_"$− 

¬q_#'− 

Base IP 65 for IQ8Alarm, white 

Base, white, for IQ8Alarm device with protection type IP 65 and surface mount cable entry. 




Base IP 65 for IQ8Alarm, red 

Base, red, for IQ8Alarm device with protection type IP 65 and surface mount cable entry. 



Type of protection IP65

Alarm Devices Conventional 

Audible Alarm Devices 

766225 

Features 

• Flat design 

• Suitable for 12 and 24 V DC operating voltage 

• Low amount of alarm current 

766226 

766239 

¬m_:h− 

¬m_;k− 

¬m_H+− 

Shallow base sounder, red 

Approval: 


VdS 

The alarm signalling device offers a selection of 32 acoustic signals including the DIN 

German standard as well as additional country-specific acoustic signals. 

The configuration is carried out via a five-pin DIL-switch. Up to two different acoustic signals 

can be activated. 

The volume can be continuously adjusted via a potentiometer. 


18 - 28 V DC 

Alarm current @ 12 V DC from 3 mA 

Alarm current @ 24 V DC from 5 mA / max. 32 mA 

DIN-Ton @ 12 V DC 7 mA 

DIN-Ton @ 24 V DC 15 mA 

Starting current max. 30 mA 

Sound level @ 12 V DC at DIN-tone 96 dB(A) 

Sound level @ 24 V DC at DIN-tone 103 dB(A 


Housing ABS V0 

Type of protection IP 54, IP 65 with 766237 



Dimensions (Ø xH) 93 x 91 mm (incl. base 766237/766238) 

Sounder with low-profile base, white 

Approval: 

As 766225 but white. 



Sounder, red 

VdS 

As per DIN 33404 - 3 and EN 457. 32 programmable signalling tones, can be selected via 

DIL-switch (two tones each), volume control via potentiometer. 





Alarm current @ 24 V DC 240mA for DIN-tone 

Sound level @ 24 V DC 112dB(A) for DIN-tone 

Ambient temperature -10 to +55°C 


Type of protection IP 21C 

Housing ABS 



237 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

238 


766261 

Accessories 

766237 

766238 

766262 


¬m_^m− 

¬m_F%− 

¬m_G(− 

¬m__p− 

Signal base 

Approval: 

Alarm sounder as per DIN 33404, - 3 and EN 457 to be mounted below detector base with 

relay output for automatic detector series 9x00; with 28 programmable signalling tones, 

can be selected via five-pole DIL switch (two tones out of 28 can be programmed), volume 

control via potentiometer. 


VdS 


Current consumption @ 12 V DC min. 5 mA, 9 mA for DIN-tone 

Starting current 30 mA for 2 ms 

Switch-on time 1.5 ms 

Sound level @ 12 V DC max. 102 dB(A)/m; 87 dB(A) for DIN-tone 






Weight 150 g 


Accessories: 

766262 Cover plate for 766261 signal base 

Base with side cable entry, red 

For alarm sounder 766225, 766226, 766410, 766411, 766412, 766413, 766414 including 

rubber seal. 





Rubber seal and two screws 

Base with side cable entry, white 

For 766236 alarm sounder but white. 


Colour white, similar RAL 9003 

Rubber seal and two screws 

Cover plate for 766261 signal base 

For covering the connection when operated without detector. 


Colour white, similar to RAL 9010


Explosion-Proof 

045040 

Features 

9 tone sequences can be programmed: 

• continuous tone 

• alternating tone 

• intermittent tone 

• siren 

• fire alarm (different national regulations taken 

into account) 

766253 

Features 

32 tone sequences can be programmed: 

• Quartz controlled sound synchronisation 

• ATEX approved 

• LM6 aluminium die-cast housing 

• Self-extinguishing aluminium cone, similar to 

UL 94 VO 

¬%SI5− 

¬m_VU− 

Ex signalling device DS10, 12V DC, 107 dB(A) 

Approval: 


VdS (FDT) 

The sound generator is especially suitable for hazardous industrial areas (zone 2 and 22). 

The robust aluminum die-cast housing is resistant to chemicals and environmental factors. 

The DS10 complies with the technical requirements of DIN 33404 - 3 “Hazard signals for 

workplaces”. 


Current consumption at Unenn approx. 300 mA 

Sound level at a distance of 1m 106 dB(A) 


Environmental class as per VdS II 



Relative humidity 90% 



Ex-category II 3GD 


According to the conformity declaration, the alarm devices can be used in zones 2 and 22. 

Ex Sounder 12V DC, 110dB(A) 

KEMA 99 ATEX 7906 design certificate 

The ex sounder is especially suitable for application in hazardous areas at industrial workplaces 

category 2G or 3G (formerly zones 1 and 2) and complies with the technical requirements 

of DIN 33404 - 3. The robust aluminium die-cast housing is resistant to chemicals 

and environmental factors. 



Rated current typ. 195 mA, 170 mA for DIN tone 

Sound level at a distance of 1m 110 dB (A) +/- 3dB depending on signalling type 




Relative humidity 90% 


Material aluminium die cast LM6 


Explosion protection type II 2 G EEx d IIC T4 

EC-type examination certificate KEMA 99ATEX 7906 

Dimensions (Ø x L) 181 x 263 mm 

239 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

240 


Optical Alarm Devices 

Conventional 

766303 

766304 

766305 

766306 


¬m`$(− 

¬m`%+− 

¬m`&.− 

¬m`'1− 

Flashing light, 12V DC, amber 




Frequency of flash approx. 1 Hz, adjustable 

Flash lamp coloured cap amber coloured 






Weight 360g 

Dimensions (Ø xH) 108 x 133 mm; (173 mm with wall mounting) 


Wall bracket included. 

Flashing light, 24V DC, amber 

As 766303 but 24 V DC operating voltage. 




Flash lamp coloured cap amber 


Wall bracket included. 

Flashing light, 12V DC, red 

As 766303 but red. 


Flash lamp coloured cap red 


Flashing light, 24V DC, red 

As 766303 but 24 V DC operating voltage and red cap. 



Current consumption 250 mA 

Lightning energy approx. 4 J


766307 

766308 

766410 

766411 

¬m`(4− 

¬m`)7− 

¬ma+?− 

¬ma,B− 

Flashing light, 12V DC, green 

As 766303 but green. 


Flash lamp coloured cap green 


Flashing light, 24V DC, green 

As 766303, but 24 V DC operating voltage and red cap. 




Flash power approx. 4 J 

Optical alarm signalling device - red 

Approval: 


VdS 

Operating voltage 9 - 60 V 


Strength of light 5 Cd 

Flash lamp cap colour red 

Frequency of flash 1 Hz 

Application temperature -25 to +70 °C 


Material base ABS 

cup PC 

Weight 150 g 

Dimensions (Ø x H) 94 x 67 mm (including base) 

Optical alarm signalling device - amber 

Approval: 


VdS 

as 766410, but amber colour 


Flash lamp cap colour amber 

241 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

242 


766412 

766413 

766414 


¬ma-E− 

¬ma.H− 

¬ma/K− 

Optical alarm signalling device - green 

Approval: 


VdS 

as 766410, but green colour 


Flash lamp cap colour green 

Optical alarm signalling device - blue 

as 766410, but blue colour and without VdS-Approval 



Flash lamp cap colour blue 

Optical alarm signalling device - transparent 

Approval: 


VdS 

as 766410, but transparent colour 


Flash lamp cap colour transparent


Combined alarm devices 

Conventional 

766240 

¬m_I.− 

Combined alarm device, 12V DC, red 

Alarm device as per DIN 33404-3 and EN 457. 

For indoor and outdoor installation (with 766237). Alarm sounder and flashing light may be 

activated separately. Floating tone going by 1 HZ beat between 1200 and 500 HZ (DIN tone). 



Alarm current flash lamp approx. 100 mA at 12 V DC 

Frequency of flash approx. 1 Hz 

Lightning energy 0.7 J 

Strength of light 10 cd 

Sound level 98 dB at 12 V DC 



Type of protection IP 54, IP 65 (with 766237) 

Housing ABS plastic (UV-stabilised) / polycarbonate 


Base red 

Weight 350 g 

Dimensions (Ø xH) 93 x 92 mm (H = 120 mm with 766237) 

Also available with cable entry at the side, possible with 766237 (see accessories). 

243 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

244 

Alarm Devices Remote Indicators 

761803 

761813 

781804 


These indicators are used primarily for signalling alarms of smoke detectors installed above 

suspended ceilings, between floors or in other inaccessible locations. The indicators have 

an elegant plastic housing with a clearly visible illuminated field. 

Cable length of the Remote Indicators to detector base or voltage supply max. 100 m. 

¬m3$5− Remote indicator, red 

Red LED display for surface mounting installation, with protective circuit for connection to 

781590 detector base and 805590 IQ8Quad detector base. 



Rated current 10mA @ 12V DC, 5mA @ 24V DC 

Alarm display 1 red LED (static) 






For Series 9000 conventional fire detectors, the 781487 adapter module is required in the 

detector base. 

¬m3.S− Remote indicator, red, flush mount version, f. detector series 9000, 9200 + IQ8Quad 

Red LED indicator as 761803, but for flush mounting on an installation socket, e.g. Ø 55 

mm. 



¬o3%:− Remote indicator, red, for detector series 9000 

Red prism is illuminated by 4 pulsed LEDs. 





Control voltage 2 to 28 V DC 

Alarm current (medium) approx. 9 mA 

Frequency of flash 1.5 Hz 

Light range red 

Angle of vision 180° 



Housing ABS plastic, white, similar to RAL 9010 


For conventional detectors, belonging to detector series 9000, the 781487 adapter module 

inside detector base is required.


781814 

781814.F0 

781815 

801824 

¬o3/X− Remote indicator for detector series 9000, 9200 and IQ8Quad 

as 761803, but 


Operating voltage 1.8 V DC 

Rated current approx. 9 mA 


Angle of vision 180 ° 




Housing ABS plastic, white, similar to RAL 9010 

Alarm display 3 red LEDs 


For conventional fire detectors, belonging to detector series 9000, the 781487 adapter module 

is required inside the detector base. 

¬o3/§/G1J− Remote indicator - Esser 

¬o30[− Remote indicator 781814/12V - Esser 

As 781814 but 



¬q39x− Remote indicator for detector series 9200 and IQ8Quad 

For operation on esserbus and esserbus-PLus 



Control voltage 2 to 28 V DC 


Alarm current (medium) 150 μA 

Frequency of flash 1,5 Hz 



Ambient temperature -20°C to +70°C (pulsed) 

Storage temperature -35°C bis 85 °C 


Housing ABS 



245 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

246 


801825 

Conventional 

043150 

Accessories 

796231 


¬q3:{− Remote indicator, blue, for series 9200 and IQ8Quad 

¬%@S-− 

¬p_@}− 

A blue prism is illuminated by 4 pulsed LEDs. Connection via three-wire cable. 



Control voltage 2 V DC to 28 V DC 


Alarm current approx. 150 μA 

Frequency of flash 1.5 Hz 


Connection terminal 0.6 mm to max. 1.5 mm 2 

Temperature range -20 °C to +70 °C 




Housing colour white (similar to RAL 9010) 


Dimensions (W x H x D) 85 x 82 x 27 (mm) 

Remote indicator, green, flashing 

In an elegant plastic housing and provided with a clearly visible illuminated field with 4 LED, 

programmable flashing mode or sustained signal. Connection without screw terminals. 


Operating voltage 10 V to 24 V DC 





Environmental class as per VdS II 

Housing colour grey-white RAL 9002 

Dimensions (W x H x D) 85 x 85 x 38,5 mm 

Label / marker ring for parallel detector indicator 

For marking 761803 and 761813 remote indicators as per DIN 14623. Plastic, red, selfadhesive 


Dimensions outside = 50 mm, inside = 10 mm 

100 pcs

Door release system Automatic Door Systems 248 

Triggering Devices 251 - 252 

Door Holding Magnets 253 - 257 

247 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

248 

Door release system Automatic Door Systems 


Automatic door systems for the demarcation of buildings and objects in closed fire compartments 

for the protection of people and valuables. 

Automatic door systems consist of triggering devices and locking devices. 

In the event of a fire, the signals created by the automatic triggering device cause the release 

of the locking device. The actuation by the manual triggering device also leads to a release 

of the locking device. 

The fire doors close and prevent the spreading of fires and of any present smoke to bordering 

areas of the building. In this way, fire and dangerous fire aerosols are contained and 

human life as well as valuables are protected. 

The locking device consists of e.g. clamping magnet with corresponding anchor plate 

and/or of an automatic door closer. The triggering device consists of the smoke protection 

switch, fire detector and release key (manual triggering device). 

In terms of building authorities, automatic door systems are subject to the Deutschen 

Institut for Bautechnik in Berlin and need a system authorization (for this, see certificates of 

approval from the DIBt). 

Arrester system for fire barriers 

Authorization number: Z-6.5-430 

System SAL 9000 FSA Smoke Heat Ventilation Module 

Authorization number: Z.-6.5-1457 

System 8000 FSA system authorization 


System IQ8FSA 8619 system authorization 


System 8000 FSA Plus system authorization 

Authorization number: Z-6.5-1808

Door release system 

Connection examples 

249 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

250 

Door release system 


Connection examples

Door release system Triggering Devices 

Smoke Heat Ventilation Modules 

782103 

¬o6$=− 


Power Supply Units for RAS 2103 

765612 

765624 

¬mY-5− 

¬mY9Y− 

Detector base for door release system type RAS 2103 

Detector base for door release system type RAS 2103 is used for direct activation of lockin 

devices in compliance with the regulations of the German Institute for Building Technique 

(DIBt). For power supply, power supply units 765612 and 765624 are required. 


Quiescent current RAS with detector approx. 20mA to approx. 25mA 

Alarm current RAS with detctor approx. 13mA to approx. 16mA 






Type of protection IP 40 with detector, IP 42 with installation plate 



The RAS 2103 may be operated with the following conventional fire detectors: 

• Rate-of-rise heat detector 761262 (series 9000) 

• Optical smoke detector 761362 (series 9000) 

Power supply unit (12 V / 3A) for automatic door release systems 

Surface mount cabinet for fire door release systems. 


Rated voltage 230 V AC / 115 V AC 



Output current max. 3 A 


Storage temperature -20°C to + 85°C 

Relative humidity max. 95 % (without condensation) 

Fuse (primary) 250 V / F 3,0 A 

Fuse +Vext. 250 V / T 3,15 A 




Dimensions (W x H x D) approx. 195 x 140 x 70 mm 


Power supply unit (12 V / 3A) for automatic door release systems 

As 765612 but 



Output current max 1.5 A 

Fuse +Vext. 250 V / T 1,6 A 

251 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

252 

Door release system Triggering Devices 

Release Keys 

767813 

767814 


¬mo.d− 

¬mo/g− 

Surface mount release key for automatic door - arrester system, German 

Surface mount release key for manual actuation of locking devices with double rocker 

switch insert. 


Version 1 NC contact, 1 NO contact 1-pole (10 A/AC 250V) 





Dimensions (W x H x D) 64 x 64 x 31.5mm 

Flush mount release key for automatic door arrester system, German 

Flush mount release key for manual actuation of locking devices with double rocker switch 

insert. 


Version 1 NC contact, 1 NO contact, 1-pin (10 A/ AC 250 V) 



Colour white 


Dimensions (W x H x D) 80.5 x 80.5 x 35.5mm

Door release system Door Holding Magnets 

Holding Magnets 

800N Holding Magnets 

768002 

¬mq#G− 

Holding Magnet with Spacer 

DIBt approved for: 

SHV module RAS 2103 : Z-6.5-1457 

Automatic door arrester system: Z-6.5-430 

Fire alarm system 8000 FSA: Z-6.5-1764 

FSA transponder: Z-6.5-1759 


Operating voltage 24 V DC (+/-10%) 

Current consumption 0.09 A 

Power consumption 2.1 W 

Operating time 100% ED 

Holding power 800 N 


Operating temperature +45°C at +20°C 


838A holding magnet with mounting plate and clamp 

Dimension Drawing 

Holding magnet and spacer are supplied. The combination can be used for wall and ground 

mounting. The spacers are available in 4 standard lengths and can be sawed off for adjustment. 

The models are prepared for ground mounting. 


Operating voltage 24V DC (for all models) 

Anchor plate is not supplied as standard. 

Mounting example 

253 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

254 


768006 

768007 

768008 

768009 


¬mq'S− 

¬mq(V− 

¬mq)Y− 

¬mq*\− 

838/839 holding magnet BW1 

Distance to wall: 115mm 










Dimension Drawing


For Ex-area 

767153 

Anchor Plates 

800N Anchor Plates 

768101 

¬mhVg− 

¬mr"F− 

Ex holding magnet 


Holding power 1568 N 

EC-type examination certificate TÜV01 ATEX 1778 X 

Ex-category II 2G 

Explosion protection EExme II T6 

Operating time 100% ED 



The anchor plate is not supplied as standard. 


Anchor plates in combination with holding magnets are the integral part of an automatic 

door arrester system. The counter-holding plates are made of special soft magnetic iron and 

the surfaces are chromium plated. The diameter of the counter-holding plate is generally a 

little larger than that of the corresponding holding magnet. This means that inaccurate 

installation will not affect holding power. 

Anchor plate (model 838-2) 

Attached to a mounting plate, with movable anchor plate for the holding magnet types 838 

and ex-door holding magnet 767153. 


255 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

256 


768103 

Door Closer 

Accessories 

767800 

796349 


¬mr$L− 

¬mo!=− 

¬p`RN− 

Anchor plate (model 838-3) 

Attached to mounting plate, with adjustment for external angle modification for the holding 

magnet types 838 and ex-door holding magnet 767153. 


DIBt approved for: 

Fire door module RAS 2103 : Z-6.5-1457 

Automatic door arrester systems for fire barriers: Z-6.5-430 

Fire detection system 8000 FSA: Z-6.5-1764 

FSA-transponder: Z-6.5-1759 

Mounting bracket for lintel installation 

Mounting bracket for all bases/detectors of the IQ8Quad group, series 9x00, RAS 2103 and 

for IQ8Alarm & all alarm devices. 

The distance between the mounting holes is 6 cm and the diameter is approx. 5 mm. 



Dimensions (L x W x H) 175 x 90 x 60 mm 

Mounting bracket and material 

Label for release push button 

Red sticker label for release key button 767813 and 767814. 

10 pcs


796356 

¬p`Yc− 

Label for release push button - Esser, German/English 

Red label, with German & English imprint “AUSLÖSUNG FEUERSCHUTZTÜR / RELEASE 

FIRE DOOR ESSER “ - for release key 767813 and 767814. 

10 pcs 

257 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

258 


Installation & Service Housings 260 - 266 

Services 267 

259 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

260 

Installation & Service Housings 

Accessories 

764708 

764723 

Features 

• Two twin wires can be connected with one 

surge protection module 

764707 


¬mP)~− 

¬mP8D− 

¬mP({− 

Surge protection for network and low-frequency signal loop 

One-part protective device suitable for rail mounting, with gas-filled triple-electrode surge 

diversion as basic protection for two signal wires (for 64KBd essernet and esserbus). 



Maximum operating voltage 560 V AC 

Rated current 2 A @ 60°C 

Rated discharge capacity 8/20μs 10 kA / 10 kA 

Output voltage limitation at 1kV/μs symm./asymm.:< 2.5 kV/


764710 

382040 

764852 

Features 

¬mP+¦− 

¬G5I¤− 

¬mQU6− 

• RS485 2 and 4 wire compatible 

• RS485 automatic mode 

• No re-configuration of transmission parameters 

required 

• Min. 1 kV electrical isolation 

• Top hat rail housing according to DIN EN 

50022-35 

• Suitable as “non-intelligent” converter for 

• RS485 field buses (e.g. profibus, CS31, etc.) 

RS232 

IP65 TG60 protective housing for 764708 and 764723 

As 764707 but 9 DU. 



Installation width 9DU (1DU = 17.5mm) 


8-fuse card 

Approval: 


VdS 

Fuse card with 8 x 0.5 A fuses for individual power supply protection of each area, zone and 

component. It can be used with all Esser mains units, fire and intrusion detection panels. 

8 fuses with T 0.5 A (supplied) 

Cover / tamper contact (S1) 

Contact load 30 V DC / 1 A 

Connection terminal 0,6 mm to max. 1,5 mm 2 



Air humidity ¥ 95 % rel. humidity (non-condensing) 

Weight approx.. 85 g 

Dimensions (W x H x D) 65 x 72 x 15 (mm) 

Possible installation in housings: 120240, 120242, 120244, 788600, 788601, 788650, 

788650.10, 788651, 788651.10, 788603 and 788603.10 

Converter RS 232 / RS 485 

For converting an interface signal from RS 232 to RS 485 and vice versa. Suitable for C-rail 

mounting. 



Baud rate 0..115200 Baud 

Voltage supply included plug-in power supply or 12..24 V AC/DC 

Current consumption typ. 85 mA at 12 V input voltage 

Connection RS232: 9-pin SUB-D plug, PC allocation FO - 

plug type 

FO - Connector type RS422: 9-pin. SUB-D plug 

Housing plastic small-design housing, 105 x 75 x 22 mm 

Weight approx. 500 g incl. power supply 

1 x interface RS232/RS485 Industry, 

1 x power supply unit 

261 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

262 


764855 

Features 

• RS-232 data rate up to 128kbps 

• TX, RX Active/Passive selectable 

• 20 or 60 mA selectable 

• DTE/DCE device setting selectable 

• TD/RD LED indicators 

• Power LED indicator 

050510 

055131 

070450 


¬mQX?− 

¬&&+P− 

¬&T@¦− 

¬(%Sa− 

Converter RS 232 / TTY 

When using this converter as, for example, a current-loop line driver (amplifier), a printer 

with a serial or parallel interface or a fire alarm panel or an intruder alarm panel can be operated 

in a distance of up to 1000m from the management system. 

Please note that two RS 232 / TTY converters are required for each connection. 

1 x converter RS232 

1 x serial connecting plug 

1 x parallel connection plug 

1 x power supply unit 

Network interference suppression filter type 2VK3 

The power supply interference suppression filter is used for retrofitting in mains power 

supplied devices, in which problems occur due to HF interference. 


Rated voltage 120 v - 250 V AC 

Rated current max. 2 A 

Mains frequency 50 - 60 Hz 

Ambient temperature -10°C to + 40°C 

Pitch 60.4 mm 

Dimensions (W x H x D) 52.6 x 46.0 x 23.1 mm (without flange) 

Mains filter and terminal block 

Sealing screws M4x6 

20 pcs 

Additional relay 12V DC 

Small PCB with relay, connection terminals, two changeover contacts. 


Maximum breaking capacity 250V AC / 5A


767503 

767513 

787402 

767510 

¬ml$@− 

¬ml.^− 

¬ok#=− 

¬ml+U− 

Control relay 12V DC 

With four changeover contacts for relay box 787402. 


Exciting voltage 12V DC 

Exciting current 120mA 

Contact rating relay 2 250V DC / 10A 


Control relay 24V DC 

As 767503 but 


Exciting voltage 24V DC 

Exciting current 69mA 



Relay box 

With plug-in holders for a maximum of two control relays (e.g. 767503 and 767513) with 

terminal strips. 


Material plastic (ABS) 




Relative humidity ¥ 95 % relative humidity (w/o condition) 


Material plastic (ABS) 

Colour grey, similar tp RAL 9002 

Weight approx. 190 g (w/o relais) 


Without control relay 

Control relay for top-hat rail mounting 


Switching voltage 12 V AC / DC bis 250 V AC / DC 

Continuous current 6 A 

Exciting voltage 12 V DC 

Contact change-over 

Switching current min. 10 mA 


Type of connection twist-on connector 

263 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

264 


788602 

788652 

788603.10 


¬ow#U− 

¬owU¦− 

¬ow$§/213− 

Top-hat rail 


Length approx. 400mm 

Mounting kit 

Mounting rail for FACP 8000 C/M and IQ8Control C/M housing 

The top hat rail installation kit can be retrofitted into the IQ8Control unit housing. The hat 

rail is fitted to the mounting board via two screws. A maximum of two 788603 module housings 

(option) can be mounted to the control unit housing. 


Dimensions (L x W) 175 x 35mm / standard-snap-on mounting rail 

Mounting rail and accessories 


Module housing for snap-on mounting rail 

For snap-on mounting rail of esserbus transponders resp. with 82 x 72 mm PCB size. 

Angled cable entry. 


Material plastic 

Colour green 


1 x UM-profile and 2 x side panels 

Application example


788605 

057633 

¬ow&^− 

¬&mBU− 

Mounting kit 

Mounting kit required for mounting esserbus transponders in extension housings. 

4 x spacer bolts and 2 x fixing screws 

Installation frame for transmission units and transponders 

Installation frame specially designed for 8000C/M and IQ8Control C/M fire alarm panels 

(IQ8Control C only with extension housing). 


Dimensions (H x W x D) 28 x 13 x 2,5 cm 

1x Installation frame, 1x insulation foil and installation material 

Application example: 

Installation option for 

808610.10 esserbus transponder 12 relays (8bit) 

808611.10 esserbustransponder32 Optocoupler(8bit) 

808613.10 esserbus transponder 4 In/2 Out (8bit) 

808614.10 esserbus transponder 1-detector zone 

057650 DS 7600 ISDN transmission unit voice transmission included 

057651 DS 7700 ISDN/IP transmission unit voice transmission included 

265 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

266 


Installation Housings 

788600 

788601 

788650.10 

788651.10 


¬ow!O− 

¬ow"R− 

¬owS§/21Y− 

¬owT§/21\− 

Housing surface mount, grey 

Small junction box housing for accommodation of esserbus transponders and the 10-pin 

distributor terminal 382030. 

The following esserbus transponders types can be used: 

- each 2 pieces of esserbus transponder (B x H x T) 82 x 72 x 20 mm 

- each 1 piece of esserbus transponder (B x H x T) 150 x 820 x 20 mm 




Material ABS 


Housing flush mount, grey 

Same as 788601, but as flush mount-version 




Material ABS 

Dimensions (WxH) 207 x 149 mm (cover) the rest as 788600 

Housing surface mount, white 

As 788600, but white. 



Housing flush mount, white 

As 788601, but white. 


Colour white, similar to RAL 9003

Installation & Service Services 

Services 

798655 

¬pwX'− 

Log book for FAS 

Log file for fire alarm systems suitable for recording operating states, events and maintenance 

work, etc. 


Format DIN A 5, 40 Pages 

267 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

268 

Notes 


Notes 

269 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

270 

Planning guide for loop installation 

This is a planning guide for loop-powered alarm devices. 

The alarm current of each alarm device is defined as load factor. When added up, the total load factor defines the 

loop length and the maximum number of alarm devices. 

The maximum load factor of all alarm devices may not exceed 96. Altogether up to 127 bus devices per loop can still 

be connected. The "Load factor" download file for easier load factor calculation is available within our customer section 

at http://www.esser-system.com. 

Load factors: 

Part No. Type of alarm signalling device Load factor 

802382 O/So optical smoke detector IQ8Quad 2 

802383 O 2 T/F multisensor IQ8Quad with integr. flash 2 

802384 O 2 T/So multisensor IQ8Quad with integr. sounder 2 

802385 O 2 T/FSp multisensor IQ8Quad with integr. flash, sounder and speech 3 

802386 O 2 T/SpSo multisensor IQ8Quad with integr. sounder and speech 3 

807205 Sounder IQ8Alarm, Housing: white 3 

807206 Sounder IQ8Alarm, Housing: red 3 

807212 Optical alert device IQ8Alarm, Housing: white, lens: amber 3 

807213 Optical alert device IQ8Alarm, Housing: white, lens: white, blue, green 3 

807214 Optical alert device IQ8Alarm, Housing: red, lens: red 3 

807224 Combi sounder IQ8Alarm, Housing: red, Lens: red 3 

807322 Speech alarm unit IQ8Alarm, Housing: white 3 

807332 Speech alarm unit IQ8Alarm, Housing: red 3 

807372 Combi speech alarm unit IQ8Alarm, Housing: red, lens: red 3 

806282 Addressable base sounder esserbus-PLus 2 

Table 1.1: Maximum loop length depending on the total load factor 

Maximum powered loop length total load factor 

bis 700 m 91 bis 96 

bis 800 m 85 bis 90 

bis 900 m 79 bis 84 

bis 1000 m 73 bis 78 

bis 1100 m 67 bis 72 

bis 1300 m 61 bis 66 

bis 1500 m 55 bis 60 

bis 1700 m 49 bis 54 

bis 2000 m 43 bis 48 

bis 2500 m 37 bis 42 

bis 3000 m 31 bis 36 

bis 3500 m 1 bis 30 


Load factor calculation 

Example 1: 

How many IQ8Alarm alarm signalling devices with load factor 3.0 can be connected to one analog loop? 

96 (max. total load factor): 3.0 (load factor) = up to 32 IQ8Alarm devices can be connected 

to each loop depending on the loop length (up to 700m) 

Example 2: 

Various types of alarm signalling devices are connected to one loop: 

Load factor 

4 x 807205 alarm devices with load factor 3,0 = 4 x 3,0 = 12 

+ 

27 x O2T/So multisensor IQ8Quad (802384) with load factor 2,0 = 27 x 2,0 = 54 

total load factor = 66 

As shown in table 1.1, the maximum loop length for a total load factor of 66 is 1300m (at a wire gauge 0,8mm). 

Example 3: 

For alarm signalling with sounder, 25 x 802384 IQ8Quad O²T/So 

detectors are installed - each in one office. What is the maximum loop length? 

Load factor for one 802384 IQ8Quad O²T/So detector = 2 (load factor) 

25 IQ8Quad O²T/So x 2 (load factor) = 50 (total load factor) 

As shown in table 1.1, the maximum loop length is 1700m (at a wire gauge 0,8mm). 

271 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

272 

OA-No. 

Order Form WINMAGplus / WINMAG Lite 

Telefax master 

Novar GmbH a Honeywell Company 

Dieselstraße 2 

D - 41469 Neuss 

1. Licence data 

Please fill in the form for data collection 

End user data (data must be entered: min. 8, max. 45 characters) 

Name: 

Street: 

Town/City/Country: 

Object: 

Installer data: (data must be entered: min. 3, max. 45 characters) 

Name: 

Street: 

Town/City/Country: 

Contact person: 

Entry of data optional: (max. 12 characters) 

Phone: 

Fax: 

Email: (max. 45 characters) 

(Please note that with completing this field, you agree that the licensing file will be sent via E-Mail.) 

2. Ordering 

One of the following must be selected. 

2.1 WINMAG control centre software basic package (select options on page 2) 

1 x 013610.10 WINMAGplus basic package 

1 x 013635.10 WINMAG Lite 

2.2 WINMAGplus retrofitting of options (select options on page 2) 

1 x 013609.10 retrofitting of options from V6.0 

2.3 WINMAG Upgrade 

1 x 013620.10 Upgrade GEMAG – Installation (MS-DOS) to WINMAGplus 

or 

1 x 013632.10 Upgrade WINMAG to WINMAGplus 

for USB interface 

for Parallel interface 

Please enter the license/update number 

Update No.: 

1 x 013636.10 WINMAG Lite Upgrade to WINMAGplus basic version 

Update No: 


Fax +49 (0) 2137 /17 - 528

Order from WINMAGplus - Part 2 


3. Options a basic license is required for each connection) 

Part No. Designation 

013630.10 Basic licence (parallel Port 1) ) 

013631.10 Basic licence (USB Port 1) ) 

013633.10 Basic licence, including dongle for USB port 

(3 month runtime version) 

013590.10 Universal Gateway for Workstations (USB Port 1) ) 

013601.10 Licence intrusion detection technology 

013626.10 Licence fire detection technology 

013603.10 Licence access control technology 

013604.10 Licence CCTV technology 

013605.10 Licence escape door control 

013657.10 WINMAGplus Licence VA/PA 4) 

013656.10 WINMAGplus Licence nurse call systems 4) 

013606.10 Licence Connection Server 

013607.10 Connection server developers kit 

013608.10 Licence - WINMAGplus remote data transmission 

013609.10 WINMAGplus control centre software - 

post installation upgrade 

013611.10 Licence OPC-Server 

013612.10 Licence OPC-Client 

013613.10 Licence Notification 

013614.10 Licence OEM 

013618.10 Licence 500 OPC/BacNet Datapoints 

013619.10 Licence translation tool 

013623.10 Licence interfacing DEZ 9000 

013624.10 Option redundance 

013625.10 Licence - WINMAGplus client 

013634.10 One-time basic licence for USB port (extension of 3 month) 

for Part No. 013633.10 

013640.10 WINMAGplus control centre software - remote-access kit 

013650.10 Licence Escalation 

013651.10 Licence DTMF 

013652.10 Licence Customied rights 

013653.10 Licence Multi Screen 

013654.10 Licence - WINMAGplus control centre software 

013655.10 Licence AutoCAD 

013660.10 Licence WEBX 

Updatenumber3) (for Winmag Version > Version 6) 

Date/Signature 

Multi-station / distributed PCs 

Computer Computer. Computer 

1) 

One of the listed part-numbers has to be chosen 

2) 

Number of PC’s, to which network data is given 

3) 

The update number is given by the info dialog window, or up from version 8, from the textfile lizenzinfo.txt 

4) Not available until Q4 / 2008 

273 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

274 

Order Information for Alarm Signaling Devices IQ8Quad and IQ8Alarm 

The IQ8Quad O²T/FSp Multi-sensor Detector (part no. 802385 ) and the IQ8Alarm "Combi" Speech Alarm (Part No. 

802385) can also be ordered with a different combination of languages. 

The following five languages are the programmed standard for these speech alarms. The respective languages are assigned 

with the five standard speech announcements for the IQ8Quad (Part No. 802385) and the IQ8Alarm (Part No. 

807372). 


Order Information: Individual Combination of Languages 

Up to five languages can be provided per alarm signaling device. 

Other combinations of languages can be ordered in accordance with the following order form. 

The delivery time is four weeks. Please note that returns or cancellations are not possible. 

Order numbers for individual combination of languages: 

IQ8Quad O²T/FSp Multi-sensor Detector 802385.SV98 

IQ8Alarm "Combi" Speech Alarm 807372.SV98 

802385.SV98 

NL_nl 

GB_en 

DE_de 

TR_tr 

RU_ru 

_____ 

Order Information: Customized Combination 

Description: 

Individual combination of languages 

802385.SV98 / 807372.SV98 

For example: 

Phrase 1 - 5 NL_nl 

Phrase 6 - 10 GB_en 

Phrase 11 - 15 DE_de 

Phrase 16 - 20 TR_tr 

Phrase 21 - 25 RU_ru 

The message type per language is always the 

same unless indicated otherwise in the chart: 

"Additional languages for individual combination”: 

1 Evacuation 1 

2 Evacuation 2 

3 Alarm 

4 Test-Message 

5 All Clear signal 

In case you should need individual texts differing from the standard speech messages, additional signal tones or other 

languages which are not listed in the order form, please contact the technical sales consultant in your area. 

Order numbers for individual programming of speech announcements / signal tones: 

IQ8Quad O²T/FSp Multi-sensor Detector 802385.SV99 

IQ8Alarm "Combi" Speech Alarm 807372.SV99 

802385.SV99 

NL_nl 

GB_en 

DE_de 

TR_tr 

RU_ru 

Extra 

Description: 

Individual combination of customer-specific 

special texts / special tones 802385.SV99 / 807372.SV99 

For example: 

Phrase 1 - 5 NL_nl 

Phrase 6 - 10 GB_en 

Phrase 11 - 15 DE_de 

Phrase 16 - 20 TR_tr 

Phrase 21 - 25 RU_ru 

Phrase 26 - 31 Extra 

(customer specific special texts / special tones) 

Information about delivery time and price of recording special texts and special tones available upon request. Please note 

that the maximum recording time is 169 seconds. Also please note that returns or cancellations are not possible. 

The programming of speech and/or tone data is carried out at the factory according to your specifications. The programming 

of the customer data is carried out via the tools 8000programming software. Please take a look at the relevant 

instructions in the online help. 

275 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

276 

Additional Languages for Individual Combination 

Country code 

acc. to ISO 

3166 -Alpha-2 

CN 

China 

Mandarin 

Language 

code acc. 

to ISO 

639-1 

zh 


Evacuation 1 Evacuation 2 Alarm Test-message All-Clear 

DK da Brandalarmen er aktiveret. 

Forlad bygningen. Anvend 

de opmærkede flugtveje. 

Elevatorerne må ikke 

Denmark 

benyttes. 

FI fi Huomio, kiinteistössä on havaittu 

automaattinen paloilmoitus. Poistu 

rakennuksesta käyttäen ohjattuja 

Finland 

reittejä. Hissien käyttö on kielletty. 

GR el Αυτό είναι ένα μήνυμα συναγερμού 

για πυρκαγιά. Παρακαλώ 

εγκαταλείψτε το κτίριο αμέσως 

Greece 

από τις εξόδους κινδύνου. Η 

πυροσβεστική έχει ειδοποιηθεί. 

NL nl Attentie, 

er is een brandalarm. 

Verlaat het gebouw via de 

Netherlands 

dichtstbijzijnde uitgang. 

ES ca Aixó es una alarma díncendi. 

Siusplau abandonin lédifici 

inmediatament per la sortida 

Catalonia 

dévacuació més propera. 

HU hu Ovo je pozarni alarm. Molimo 

odmah napustite objekt koristeci 

najblizi izlaz za nuzdu. Vatrogasna 

Croatia 

postaja je alarmirana. 

NO no Brannalarmen er utløst. Forlat 

bygget. Bruk de oppmerkede 

rømningsveier. Heisene må ikke 

Norway 

brukes. 

PL pl Uwaga! Wystąpił alarm pożarowy. 

Proszę natychmiast opuścić 

budynek najbliższym dostępnym 

Poland 

wyjściem ewakuacyjnym. 

PT pt Isto é um alarme de incêndio. 

Por favor abandonem o edifício 

imediatamente pela saída de 

Portugal 

evacuação mais próxima. 

RO ro Atenţiune, atenţiune! S-a declanşat 

o alarmă de incendiu. Vă rugăm 

părăsiţi imediat clădirea pe cea mai 

Romania 

apropiată cale de evacuare. 

Alarma a fost transmisă la pompieri. 

RU ru Внимание. Пожарная тревога. 

Пожалуйста покиньте помещение 

через ближайшие аварийные 

Russia 

выходы. 

SE sv Brandlarmet är utlöst. Utrymm 

byggnaden. Använd de uppmärkta 

utrymningsvägarna. Hissar får inte 

Sweden 

användas. 

SK sk Toto je požiarny poplach. Opusťte 

prosim okamžite budovu najbližším 

núdzovým východom! 

Slovakia 

CZ cs Toto je požární poplach. 

Prosím, opusťte okamžitě 

budovu nejbližším únikovým 

Czech 

Republic 

východem. 

TR tr Dikkat ! Dikkat ! Acil 

Yangın Uyarısı. Lütfen 

dirhal binayı boşaltın. 

Turkey 

HU hu Tűzriadó! Kérem, azonnal 

hagyják el az épületet az 

Önökhöz legközelebb eső 

Hungary 

kijáraton! 

Huomio, turvallisuussyistä 

kiinteistöstä on poistuttava 

välittömästi. Käytä ohjattuja reittejä. 

Et varsel om brand bliver 

undersøgt. Afvent nærmere 

besked. 

Huomio, paloilmoitin on ilmoittanut 

mahdollisesta vaaratilanteesta. 

Tutkimme asiaa ja annamme 

pian lisätietoja. 

Προσοχή, προσοχή! Αυτό είναι Προσοχή στο κτίριο υπάρχει 

ένα μήνυμα για κατάσταση κατάσταση κινδύνου. Παρακαλώ 

κινδύνου. Παρακαλώ εγκαταλείψτε παραμείνετε ψύχραιμοι και περιμένετε 

το κτίριο από τις επόμενες εξόδους. επόμενες οδηγίες. 

Attentie, 

er is een calamiteit. 

Verlaat het gebouw via de 

dichtstbijzijnde uitgang. 

Atenció. Aixó es una emergencia. 

Siusplau abandonin lédifici per la 

sortida dévacuació més propera. 

Pozor! Pozor! Ovo je priopcenje o 

neposrednoj opasnosti. Molimo 

odmah napustite objekt koristeci 

najblizi izlaz za nuzdu. 

Proszę o uwagę! To jest komunikat 

alarmowy. Proszę opuścić budynek 

najbliższym dostępnym wyjściem 

ewakuacyjnym. 

Atenção. Isto é uma emergência. 

Por favor abandonem o edifício 

pela saída de emergência mais 

próxima. 

Atenţiune! Acesta este un mesaj de 

urgenţă. Vă rugăm părăsiţi clădirea 

pe cea mai apropiată cale de ieşire. 

Внимание. Это предупреждение о 

пожарной опасности. Пожалуйста 

покиньте помещение через 

ближайшие выходы. 

Pozor, hrozí nebezpečenstvo. 

Opusťte prosim budovu 

najbližším núdzovým 

východom! 

Pozor, hrozí nebezpečí. 

Prosím, opusťte budovu 

nejbližším únikovým 

východem. 

Acil bir durum var. Lütfen 

binayı en yakın çıkış 

noktasından terkedin. 

Figyelem! Vészhelyzet! 

Kérem, azonnal hagyják el 

az épületet az Önökhöz 

legközelebb eső kijáraton! 

Attentie, 

er volgt een blussing, 

verlaat de ruimte. 

Atenció. S´ha notificat un 

incident a lédifici. Siusplau, 

esperin altres instruccions. 

Pozor! U objektu je prijavljena 

opasnost. Molimo ostanite 

mirni i pricekajte daljnje 

upute. 

Et automatisk varsel om brann blir 

undersøkt. Avvent nærmere beskjed. 

Uwaga. W budynku wystąpiło 

zdarzenie alarmowe. Proszę spokojnie 

oczekiwać dalszych instrukcji. 

Atenção, ocorreu um incidente no 

edifício. Por favor aguardem mais 

instruções. 

Atenţiune. În clădire a fost semnalat 

un incident. Vă rugăm să vă păstraţi 

calmul şi să aşteptaţi noi instrucţiuni. 

Внимание. Поступило 

предупреждение о пожарной 

опасности. Пожалуйста сохраняйте 

спокойствие и ждите дальнейшей 

информации. 

Ett automatiskt varsel om brand blir 

undersökt. Invänta närmare besked. 

V budove bola vyhlásená 

pohotovosť. Počkajte prosim 

na ďalšie pokyny. 

V budově byla vyhlášena 

pohotovost. Prosím, vyčkejte 

dalších instrukcí. 

Bu bir yangın uyarısıdır. Bu 

bir yangın uyarısıdır. 

Talimatlar için beklemede 

kalın. Talimatlar için beklemede 

kalın. 

Az épületben váratlan esemény 

történt. További utasításig 

kérem várjanak! 

Dette er en testmelding. 

Paloilmoitinjärjestelmää 

testataan. 

Αυτή είναι μια δοκιμαστική 

ανακοίνωση. 

Dit is een testalarm, 

dit is een testalarm. 

Aixó es un missatge 

de prova. No es 

requereix cap acció. 

Ovo je probno 

priopcenje. Nikakve 

mjere nisu neophodne. 

Dette er en testmelding. 

To jest komunikat testowy. 

Nie są wymagane żadne 

działania. 

Atenção, isto é apenas um 

ensaio 

Situaţia de urgenţă a luat 

sfârşit. Ne cerem scuze 

pentru eventualele 

inconveniente. 

Отмена пожарной тревоги. 

Ситуация нормализовалась. 

Извините за причинённые 

неудобства. 

Tekniskt prov av brandlarmet. 

Toto je testovacie 

hlásenie. Nie je 

potrebne naň 

reagovať. 

Toto je testovací 

hlášení. Není třeba na 

něj reagovat. 

Yangın uyarısı test 

edilmektedir. Bir şey 

yapmanız gerekmiyor. 

Bir şey yapmanız 

gerekmiyor. 

Ez egy tesztüzenet. 

Normal tilstand er 

genoprettet. Faren er 

overstået. 

Palohälytys on ohi. Tilanne 

on palautunut normaaliksi. 

Η κατάσταση κινδύνου έχει 

αρθεί. Ζητούμε συγγνώμη 

για τυχόν δυσάρεστες 

καταστάσεις που προκλήθηκαν. 

Einde alarmmelding, 

einde alarmmelding. 

Lálarma ha estat 

cancel.lada. Preguem 

disculpin les molesties. 

Opasnost je prestala. 

Ispricavamo se radi 

eventualnih neugodnosti. 

Normal tilstand er 

gjenopprettet. Faren over. 

Stan alarmu został odwołany. 

Przepraszamy za wszelkie 

niedogodności i utrudnienia. 

O alarme foi cancelado. Queiram 

desculpar o inconveniente. 

Acesta este un mesaj de test. 

Тестовое сообщение. Идет 

проверка системы 

пожарной сигнализации. 

Normal tilstånd är återupprättat. 

Faran är över. 

Pohotovosť bola 

odvolaná.Ospravedlňujeme 

sa za pripadne ťažkosti. 

Pohotovost je nyní 

odvolána. Omlouváme se 

za případné obtíže. 

Tehlike geçmiştir. Tehlike 

geçmiştir. Bir şey yapmanız 

gerekmiyor. 

Vészhelyzet törölve. Az 

esetleges 

kellemetlenségekért 

elnézésüket kérjük.

Order Form for Individual Combination of Languages 

Novar GmbH FAX No. 02137 / 17 -366 

Vertriebsinnendienst 

Dieselstraße 2 

41469 Neuss 

1. Customer Data 

Please fill out the following form for the registration of these data. 

Company: Customer ID: 

Street: Zip Code/City: 

Contact Person: E-mail: 

Telephone: Fax: 

Object: 

Order Number / Order Text: 

Novar Order Number: 

2.Type / Amount 

802385.SV98 Amount 

807372.SV98 Amount 

3. Languages 

Languages Country Code according Code according to 

max. 5 languages to Speech ISO 3166 ISO 639-1 

Chinese Mandarin CN zh 

Danish DK da 

German DE de 

English GB en 

Finnish FI fi 

French FR fr 

Greek GR el 

Dutch NL nl 

Italian IT it 

Catalan ES ca 

Croatian HR hr 

Norwegian NO no 

Polish PL pl 

Portuguese PT pt 

Romanian RO ro 

Russian RU ru 

Swedish SE sv 

Slovak SK sk 

Spanish ES es 

Czech CZ cs 

Turkish TR tr 

Hungarian HU hu 

Repeat Orders or Additions 

For repeat orders or additions please give the Order No. or 

the serial number of the detector with special languages. 

Date/Signature 


Order number: 

Serial number: 

To be filled out by Novar GmbH: 

Please forward to Production when filled out! 

Order number: 

Position: 

277 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

278 

Part Number Index 

Part No. Page Part No. Page Part No. Page Part No. Page 

013330.10 83 

013331.10 83 

013332.10 83 

013405.10 92 

013590.10 91 

013601.10 89 

013603.10 89 

013604.10 89 

013605.10 90 

013606.10 91 

013607.10 91 

013608.10 90 

013609.10 88 

013610.10 87 

013611.10 92 

013612.10 92 

013613.10 93 

013614.10 95 

013616.10 88 

013617.10 88 

013618.10 91 

013619.10 94 

013623.10 90 

013624.10 94 

013625.10 94 

013626.10 89 

013630.10 87 

013631.10 87 

013633.10 87 

013634.10 88 

013635.10 98 

013636.10 98 

013640.10 94 

013650.10 93 

013651.10 93 

013652.10 93 

013653.10 94 

013654.10 90 

013655.10 95 

013656.10 90 

013657.10 91 

013660.10 93 

018001 63 

018002 63 

018003 63 

018004 63 

018005 63 

018006 63 

018007 63 

018008 63 

018010 63 

043150 246 

045040 239 

050510 262 

055131 262 

057633 265 

060426 129 

060427 129 

060429 133 

060430.10 132 


060431 133 

060865 221 

070300 72 

070450 262 

382001 8 

382010 8 

382011 8 

382040 261 

382201 8 

701040 144 

704070 145 

704477.10 142 

704800 143 

704801.10 143 

704804 143 

704850 143 

704854 143 

704870 143 

704874 143 

704890 143 

704900 141 

704901 141 

704902 141 

704903 141 

704904 141 

704910 144 

704911 144 

704912 145 

704917 144 

704951 151 

704960 151 

704961 152 

704964 151 

704965 152 

704966 152 

704967 153 

704975 151 

704980 153 

704981 153 

736235 24 

736235 32 

736264 32 

743212 39 

743245 39 

743248 39 

744027 40 

744028 40 

744029 40 

744030 40 

750707 32 

761162 102 

761162.F0 102 

761220 52 

761221 52 

761226 53 

761227 53 

761228 53 

761230 53 

761243 191 

761244 192 

761245 192 

761246 192 

761247 192 

761262 102 

761262.VC0 103 

761290 191 

761315 196 

761316 197 

761321 198 

761322 199 

761323 199 

761345 219 

761346 220 

761347 181 

761348 182 

761349 183 

761362 103 

761362.VC0 103 

761400 194 

761401 194 

761402 194 

761403 195 

761404 195 

761405 195 

761406 195 

761407 195 

761500 203 

761501 206 

761502 204 

761503 208 

761504 209 

761505 209 

761506 209 

761507 207 

761508 208 

761510 210 

761511 210 

761512 210 

761515 205 

761516 206 

761517 209 

761518 210 

761519 202 

761520 220 

761521 220 

761522 221 

761523 221 

761524 221 

761525 221 

761526 222 

761527 222 

761528 222 

761529 222 

761530 223 

761531 223 

761532 224 

761533 224 

761534 223 

761535 224 

761536 224 

761537 224 

761542 225 

761543 225 

761544 225 

761546 226 

761547 226 

761630 154 

761694 155 

761697 156 

761803 244 

761813 244 

762400 203 

762401 207 

762402 207 

762403 204 

762404 208 

762405 208 

762406 205 

762407 205 

762410 203 

762411 207 

762412 207 

762413 204 

762414 208 

762415 208 

762416 205 

762417 206 

762420 203 

762421 207 

762422 207 

762423 204 

762424 208 

762425 208 

762426 205 

762427 206 

762430 203 

762431 207 

762432 207 

762433 204 

762434 208 

762435 208 

762436 205 

762437 206 

763262.F0 103 

763362.F0 103 

764701 31 

764707 260 

764708 260 

764710 261 

764723 260 

764744 118 

764745 118 

764752 119 

764754 119 

764790 65 

764818 68 

764852 261 

764855 262 

764896 72 

765612 251



765624 251 

766061 117 

766062 117 

766063 117 

766064 118 

766225 237 

766226 237 

766237 238 

766238 238 

766239 237 

766240 243 

766253 239 

766261 238 

766262 238 

766303 240 

766304 240 

766305 240 

766306 240 

766307 241 

766308 241 

766410 241 

766411 241 

766412 242 

766413 242 

766414 242 

767153 255 

767503 263 

767510 263 

767513 263 

767800 256 

767813 252 

767814 252 

768002 253 

768006 254 

768007 254 

768008 254 

768009 254 

768101 255 

768103 256 

768308 28 

768318 28 

768398 28 

768408 35 

768408.VC0 35 

768411 29 

768418 34 

768420 29 

768428 34 

768438 35 

768448 34 

769070 134 

769080 135 

769163 38 

769164 38 

769803 123 

769813 134 

769814 134 

769828 43 

769836 127 

769870.20 133 

769871.20 134 

769910 145 

769911 145 

769914 39 

769915 39 

769916 145 

769921 144 

770392 29 

770393 29 

771365 103 

771669 30 

771794 30 

772084 38 

772147 32 

772180 154 

772331 31 

772333 31 

772363 33 

772365 33 

772366 33 

772384 166 

772386 77 

772387 77 

772388.10 166 

772445 24 

772476 23 

772477 23 

772478 23 

772479 23 

775814 47 

781332 228 

781332.F0 228 

781333 228 

781335 62 

781336 62 

781337 62 

781443 184 

781444 185 

781445 186 

781446 185 

781447 185 

781448 186 

781449 186 

781453 187 

781454 188 

781456 188 

781457 189 

781458 189 

781459 189 

781460 190 

781482 135 

781487 123 

781495 122 

781495.F0 122 

781496 122 

781497 122 

781497.F0 122 

781498 123 

781498.F0 123 

781550 136 

781588 120 

781590 120 

781590.F0 120 

781682 146 

781692 146 

781693 146 

781694 146 

781695 146 

781696 146 

781697 147 

781698 147 

781699 147 

781804 244 

781814 245 

781814.F0 245 

781815 245 

782103 251 

782313 180 

783000 55 

783001 56 

783003 55 

783005 56 

783250 57 

783251 57 

783252 57 

783253 58 

783254 58 

783255 58 

783256 58 

783257 166 

783258 166 

783259 166 

783312 180 

783313 180 

783590.F0 120 

784026 30 

784141 31 

784381 35 

784382.D0 36 

784385 36 

784710 68 

784725 71 

784726 71 

784743 69 

784744 69 

784753 70 

784754 70 

784760 30 

784763 75 

784764 76 

784765 76 

784830.10 95 

784832.10 95 

784833.10 95 

784839.10 95 

784840 74 

784841 75 

784842 36 

784843 75 

784847 84 

784855 76 

784856 76 

784859 77 

784865 75 

784883 33 

784885 32 

784892 24 

785000 79 

785001 79 

785002 79 

785003 79 

785004 79 

785006 80 

785007 80 

785008 80 

785009 80 

785010 80 

785011 80 

785012 80 

785013 80 

785015 81 

785016 81 

785017 81 

785018 81 

785019 81 

785020 81 

785021 81 

785022 82 

785024 82 

785025 82 

785026 82 

785027 82 

785028 82 

785029 82 

785030 82 

785031 82 

785033 82 

785034 82 

785035 82 

785101 66 

785102 66 

785103 66 

785104 66 

785105 66 

785107 66 

785108 66 

785653 60 

785655 61 

785753 63 

786000 21 

786001 19 

786100 21 

786101 19 

786261 22 

786262 22 

786263 22 

786301 20 

786401 20 

786452 20 

786501 20 

279 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

280 



786552 20 

786801 20 

786901 21 

786952 21 

787402 263 

787530 36 

787531 37 

787532 37 

787533 37 

788012 45 

788013 45 

788014 50 

788014.CZ 50 

788014.E 50 

788014.GB 50 

788014.PL 50 

788014.RO 50 

788014.SK 50 

788015 50 

788016 46 

788016.NL 46 

788024 49 

788024.CZ 49 

788024.E 49 

788024.GB 49 

788024.PL 49 

788024.RO 49 

788024.SK 49 

788025 49 

788093 21 

788139 67 

788140 67 

788297 44 

788298 44 

788400 46 

788401 46 

788600 266 

788601 266 

788602 264 

788603.10 264 

788604 83 

788605 265 

788606 77 

788609 84 

788612 167 

788650.10 266 

788651.10 266 

788652 264 

788653 51 

788654 51 

788705 9 

788706 9 

788706.GB0 9 

788730 38 

789300 13 

789301 13 

789302 14 

789303 24 

789304 18 

789305 84 


789310 25 

789855 123 

789856 124 

789860.10 41 

789861 41 

789862.10 42 

789863 42 

789864 43 

789907 58 

796231 246 

796349 256 

796356 257 

797595 210 

798655 267 

801372 220 

801372.SV082.N4 220 

801515 212 

801519 201 

801519.E0 201 

801519.F0 201 

801519.GB0 201 

801519.I0 201 

801521 213 

801522 214 

801523 216 

801524 217 

801525 217 

801531 215 

801532 216 

801533 217 

801534 217 

801535 217 

801540 217 

801541 218 

801542 218 

801543 218 

801547 218 

801548 219 

801549 219 

801550 226 

801551 227 

801552 227 

801553 227 

801554 227 

801555 227 

801556 227 

801557 227 

801558 227 

801559 227 

801560 227 

801561 227 

801562 227 

801563 227 

801564 227 

801565 227 

801566 227 

801567 227 

801824 245 

801825 246 

801979 188 

802171 105 

802171.F 105 

802177 105 

802271 106 

802271.F 106 

802371 106 

802373 107 

802374 108 

802374.F 108 

802375 107 

802375.F 107 

802379 185 

802382 112 

802383 112 

802384 112 

802385 113 

802385.SV98 113 

802385.SV99 113 

802386 113 

802473 108 

803271 106 

803271.EX 115 

803371 107 

803371.EX 115 

803374 108 

803374.EX 115 

804382.D0 36 

804473.10 142 

804791 65 

804863 168 

804864 168 

804868 170 

804869 169 

804870 170 

804900 139 

804901 139 

804902 139 

804905 140 

804906 140 

804950 150 

804955 150 

804970 148 

804970.VC0 148 

804971 149 

804973 149 

804973.F0 149 

805551 130 

805552 131 

805553 131 

805570 126 

805571 125 

805572 127 

805573 126 

805574 125 

805576 125 

805577 126 

805580 128 

805581 129 

805582 131 

805583 132 

805586 132 

805587 124 

805588 124 

805589 124 

805590 121 

805591 121 

805593 173 

805594 174 

805595 175 

805597 64 

805601 176 

805602 177 

805603 177 

805604 177 

805605 178 

805863 168 

805864 169 

806201 236 

806202 236 

807205 233 

807206 233 

807212 235 

807213 235 

807214 235 

807224 234 

807322 233 

807332 233 

807372 234 

807372.SV98 234 

807372.SV99 234 

808003 12 

808004 17 

808020 14 

808030 17 

808031 17 

808139 12 

808218 18 

808219 17 

808610.10 158 

808611.10 159 

808613.10 160 

808613.20 161 

808613.30 162 

808614.10 163 

808615 163 

808619.10 164 

808621 166 

808622 165 

808625 167 

808630.10 165 

808631.10 166 

821056 56 

821057 57 

BME2Z002 43

Notes 

281 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

282 

Index 

Keyword Page 

1 prism for Fireray 199 

19” mounting kit for FACP 8008, operating unit front 

32 

19” mounting kit for retrofitting 32 

19” rack mounting kit for SZI 192 detector zones 21 

3.6V lithium battery 64 

3-relay common fault module 37 

3-relay module 37 

3-way-sphere tap (PVC) for 25mm pipe 223 

4 prisms for Fireray 199 

45° angle (PVC) for 25mm pipe 221 

4inch trim ring and snap-in mounting clips for 

IQ8Quad detector base 125 

4-relay module 36 

4-zones fire detection module 35 

8000 FACP remote serial essernet interface 77 

838/839 holding magnet BW1 254 




838A holding magnet with mounting plate and 

clamp 253 

8-fuse card 261 

90° angle (PVC) for 25mm pipe 221 

90° bend (PVC) for 25mm pipe 220 

Accumulator / battery kit 63 

Adapter for Esser pole (Part No. 769813) 129 

Adapter module ADP- PRS-422 70 

Adapter module ADP-PRS-232 70 

Adapter module for base 781590 123 

Adaptor module ADP-N3E 69 

Additional relay 12V DC 262 

Alarm and monitoring module for IQ8TAM 170 

Analog loop module 36 

Analog loop module powered loop 36 

Anchor plate (model 838-2) 255 

Anchor plate (model 838-3) 256 

ARS 70-1 analog line type aspirating smoke 

detection system 219 

ARS 70-2 aspirating smoke detection system for 

two detectors 220 

Aspirating smoke detector unit LRS 100 - Esser, 

German 203 

Aspiration reducing film sheet 2,0 mm 227 

















Back-flow valve for Titanus EB 218 

Banderole for suction-reducing foil 226 

Base cover for IQ8Quad 124 

Base IP 65 for IQ8Alarm, red 236 

Base IP 65 for IQ8Alarm, white 236 

Base with side cable entry, red 238 

Base with side cable entry, white 238 

Basic license extension for USB port 88 

Basic license for USB port 3 month duration 87 

Basic license for WINMAGplus parallel port 87 

Basic license for WINMAGplus USB port 87 


Keyword Page 

Basic unit Titanus Pro Sens 2 EB 214 

Basic unit Titanus Pro Sens EB 213 

Basic unit Titanus Top Sens 2 without module 216 

Basic unit Titanus Top Sens EB 215 

Battery 12 V DC / 1.2 Ah capacity 63 


Battery 12 V DC / 10 Ah capacity 63 





Battery 12V DC / 2.6 Ah capacity 63 

Battery 12V DC / 65Ah capacity 63 

Battery extension housing 13 

Blank front face for non used place for 

CMSI 8000 58 

Bus CMSI 8000 58 

Cabinet extension for CMSI 8000 56 

Carrying bag for test equipment including 

cover for telescopic rods 132 

CD ROM with software VConfig PRO and 

ASPIRE 210 

Ceiling bracket for LRMX 761400 for distances 

400 to 700 mm 195 

Ceiling bracket for LRMX 761400 for distances 

700 to 1500 mm 195 

CMSI 1 function 56 

CMSI 10 functions 57 

CMSI 32 functions in cabinet 55 

CMSI 8000 rack-mount 19” 32 functions 55 

CO capsule for Multi-stimulus detector tester 

805551 131 

CO test gas for smoke detector tester 805582 132 

Combined alarm device, 12V DC, red 243 

Compact unit Titanus Pro Sens EB 212 

Connection link set for sensor cable 192 

Connection server developers kit 91 

Connection set for panel 8010 Series 2 and 3 in 

19-inch technology (3 HU), 1m 51 

Control center software CD WINMAGplus 

basic kit 87 

Control panel interface RS 232 43 

Control relay 12V DC 263 

Control relay 24V DC 263 

Control relay for top-hat rail mounting 263 

Conventional MCP electronic module 139 

Conventional MCP electronic module w/o snap-on 

function 139 

Conventional MCP electronic module with glass - 

Esser 150 

Conventional MCP electronic module with second 

microswitch 139 

Conventional MCP, red housing with glass pane - 

Esser 148 

Conventional MCP, red housing with glass pane - 

Esser, China 148 

Conversion kit for smoke detector tester 769870 134 

Converter RS 232 / RS 485 261 

Converter RS 232 / TTY 262 

Corrugated polyester hose 225 

Cover plate for 766261 signal base 238 

CPU card for FACP 8008 30 

Cross piece for 25mm pipe 221 

Data points package 91 

DC/DC converter 12V/24V DC 62 

DC/DC converter output voltage 62 

DC/DC converter output voltage 24 V DC 62 

Demo case for IQ8Quad detector with integrated 

alarm device 127 

Detection point input 95 

Detector base for door release system type 

14

Index 

Keyword Page 

RAS 2103 251 

Detector base with relay contact for IQ8Quad 121 

Detector base with relay contact for series 9000 120 

Detector cover for detectors Series 9x00 

and/or base 124 

Detector cover for detectors Series 9x00 with 

base adapter 123 

Detector cover for IQ8Quad with built-in alarm 

sounder 124 

Detector cover for IQ8Quad without built-in 

alarm sounder 124 

Detector dismounting tool for series 

9000/9100/9200 123 

Detector locking for series 9x00 122 

Detector module 0.05%/m DM-TP-05 217 

Detector module 0.05%/m DM-TT-05 217 





Detector removal tool 128 

Detector unit LRS-S 700 - Esser, German 204 

Device holder for aspirating smoke detection 

systems Titanus EB 217 

Diagnostics tool for Titanus EB 219 

Door contact for upright cabinet 38 

Dummy cover 19”, 2 HU 40 




ECS 8000M 19”- Esser, French 44 

Emergency file depot DIN A4 horizontal layout for 

2 x 64 cards, red 72 

Emergency file depot DIN A4 horizontal layout for 

10 pcs. routing cards, red - German 72 

End cap (PVC) for 25mm pipe 222 

EOL-Z Module for detector groups 167 

esserbus communication transponder 163 

esserbus transponder 1 IN 163 

esserbus transponder 12 relays (8bit) 158 

esserbus transponder 32 LED (8bit) 159 

esserbus transponder 4 detector groups / 

2 relays 161 

esserbus transponder 4 IN / 2 OUT 160 

esserbus Transponder 4 IN / 2 OUT - Esser, 

Dutch 166 

esserbus Transponder 4E 2S 808613.F0 with 

housing - Esser, French 166 

esserbus transponder for door release 

application 164 

esserbus Transponder for UniVario 165 

esserbus Transponder SST 162 

essernet module 62.5kBd 74 

essernet module 500kBd 75 

essernet repeater 500kBd 75 

essernet repeater 62.5kBd 75 

Ex Fixed heat detector 1161, Series 9100 117 

Ex holding magnet 255 

Ex manual call point (conventional) IP66 156 

Ex Optical smoke detector, Series 9100 117 

Ex OT-multisensor detector, Series 9100 118 

Ex Rate-of-rise heat detector 1261, Series 9100 117 

Ex safety barrier for intrinsic safe of detectors 

Series IQ8Quad and 9100 118 

Ex signalling device DS10, 12V DC, 107 dB(A) 239 

Ex Sounder 12V DC, 110dB(A) 239 

Extension chassis S1-E for FACP 8008 31 

Extension housing 24 

Extension housing for batteries and SZI 192 

detector zones 13 

Extension housing for Package Part No. 808218 

IQ8Control M 18 

Keyword Page 

Extension housing for SZI 192 detector zones 14 

Extension housing kit S1-E for FACP 8008 31 

Extension module with 3 additional micromodule 

slots 23 

Extension module with one additional 

micromodule slot 23 

Extension pole 134 

External power supply unit 12V DC / 2A 60 

External power supply unit 24V DC / 1A 61 

Extinguishing control panel 8010 Series 2 w/o 

operating unit 49 

Extinguishing control panel 8010 Series 2 with 

operating unit - Esser, Czech 49 


operating unit - Esser, English 49 


operating unit - Esser, German 49 


operating unit - Esser, Polish 49 


operating unit - Esser, Romanian 49 


operating unit - Esser, Slovak 49 


operating unit - Esser, Spanish 49 

Extinguishing control panel 8010 Series 3 w/o 



operating unit - Esser, Czech 50 


operating unit - Esser, English 50 


operating unit - Esser, German 50 


operating unit - Esser, Polish 50 


operating unit - Esser, Romanian 50 


operating unit - Esser, Slovak 50 


operating unit - Esser, Spanish 50 

Extinguishing panel 8010, Series 3 w/o 


Extinguishing panel 8010, Series 3 with 


FACP 80-4 - Esser, German, 24 V DC 9 

FACP 80-8 - Esser, English, 24V DC 9 

FACP 80-8 - Esser, German, 24 V DC 9 

FACP IQ8Control M 17 

FACP IQ8Control M for 19” cabinet 17 

FB inform./operating system, A3 horizonal layout, 

individual locking - German 71 

FB inform./operating system, A4 horizonal layout, 

individual locking-German 71 

Fibre optic converter for essernet, Multi-Mode with 

F-SMA male connection 76 

Fibre optic converter for essernet, Multi-Mode with 

F-ST male connection 75 

Fibre optic converter for essernet, Single-Mode 76 

Field bus interface PLus 42 

Filler panel front, neutral for IQ8Control C/M 21 

Filler panel module left 33 

Filler panel module right 33 

Filter cartridge for air duct module 781443 185 

Filter chamber for 25mm pipe 224 

Fire / Intruder Alarm Panel 2001 - english 

language 8 

Fire / Intruder alarm panel 2001 - Esser, Dutch 8 

Fire / Intruder Alarm Panel 2001 - Esser, German 8 

Fire / Intruder Alarm Panel 2001 - Esser, Russian 8 

Fire alarm panel 8008 for 19” cabinet - Esser 28 

Fire alarm panel 8008 in S1 housing - Esser 28 

283 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

284 

Index 

Keyword Page 

Fire alarm panel 8008 in S1-E housing - Esser 28 

Fire alarm panel ECS 8000 M - Esser, French 44 

Fire alarm panel IQ8Control C 12 

Fire alarm panel IQ8Control C for 19” cabinet 12 

Fire brigade operating panel - Germay 68 

Fire brigade operating panel (FBF-Ö) - Austria 68 

Fire department indicating panel FAT3000 69 

Fireray 100 RV, with four prisms 197 

Fireray 2000 198 

Fireray 50 RV, with one prism 196 

Fixed heat detector 102 

Fixed heat detector - Esser, France 102 

Fixed heat detector class B IQ8Quad 105 

Fixed heat detector IQ8Quad 105 

Fixed heat detector IQ8Quad - France 105 

Flange for climate channel (PVC) for 25mm 

pipe 222 

Flashing light, 12V DC, amber 240 

Flashing light, 12V DC, green 241 

Flashing light, 12V DC, red 240 

Flashing light, 24V DC, amber 240 

Flashing light, 24V DC, green 241 

Flashing light, 24V DC, red 240 

Flat cable 40-pin for 19” rack mounting 32 

Flush mount base adapter for series 9x00 122 

Flush mount base adapter for series 9x00 - 

Esser, 

France 122 

Flush mount kit for base IQ8Quad 125 

Flush mount release key for automatic door 

arrester system, German 252 

Flush mounting kit for LRS 210, 110, 120, 710, 

720 control panels 210 

Flush mounting kit for LRS 100 and 700 

detectors 210 

Foil for front face w. universal text for large 

MCP ABS 70490x 144 

Foil for front face w. universal text for large 

MCP ABS, black lettering 145 

Foil for front face w. universal text for small 

MCP, white lettering 152 

Front face 1 alarm managed unit for 

CMSI 8000 57 

Front face 12 functions UCMC for CMSI 8000 57 

Front face 12 zones for manual call points for 

CMSI 8000 58 

Front face 4 security functions for CMSI 8000 57 

Front foil Titanus Pro Sens 2 EB 218 

Front foil Titanus Top Sens 2 EB 219 

Gateway for FACP 3007/3008/3010 @ System 

8000, IQ8Control 38 

Graphics page conversion 95 

Graphics page input 95 

Hardware Option TCP/IP converter, Ethernet 

RS232/RS485 92 

Hose with textile insertion (PVC) for 25mm pipe 222 

Housing flush mount, grey 266 

Housing flush mount, white 266 

Housing for ex barrier 119 

Housing for small MCP, blue 151 

Housing kit 77 

Housing surface mount, grey 266 

Housing surface mount, white 266 

Housing with glass pane, blue, similar to 

RAL 5015 141 

Housing with glass pane, green, similar to 

RAL 6002 141 

Housing with glass pane, orange, similar to 

RAL 2011 141 

Housing with glass pane, red, similar to 

RAL 3020 141 


Keyword Page 

Housing with glass pane, yellow, similar to 

RAL 1021 141 

Housing with glass, red , in compliance 

with EN 54-11 143 

IGIS-LOOP controller (in housing ZG2) 83 

IGIS-LOOP controller kit for FACP 8000C, C 

IQ8Control or EMZ 5008C 84 

IGIS-LOOP controller kit for FACP 8000M, 

IQ8Control M 84 

IGIS-LOOP controller kit kit for FACP 8008 83 

IGIS-LOOP-Controller 83 

IGIS-LOOP-Controller (in housing ZG0) 83 

Indicating & operating panel for networked 

FACP (Repeater) 67 

Indicating & operating panel for networked 

FACP (Repeater), slim-line 67 

Indicating and operating panel f. releasing 

control equipment 8010 series 2 + 3, English 46 

Indicating and operating panel f. releasing 

control equipment 8010 series 2 and 3 46 

Indicator and operating module LRS 110 - 

Esser, English 207 


Esser, French 207 


Esser, German 206 


Esser, Italian 207 


Esser, Spanish 207 

Indicator and operating module LRS-120 - 










Indicator and operating module LRS-S 710 - 


Indicator and operating module LRS-S 720 - 


Indicator and operating module LRS-S710 - 
















Input/output (I/O)-card for micromodules - Esser 30 

Installation frame for transmission units and 

transponders 265 

Interface module RS232/V24 77 

Interface module TTY/CL 20mA 77 

Intermediate distribution frame for IQ8Control C 25 

Internal module for MCP zones or link with fire 

detection panel 58 

IP 43 moisture-proof surface-mounted base 

adapter aP for IQ8Quad detector base 127 

IP 43 protection for detector base IQ8Quad, 

flat design 126

Index 

Keyword Page 

IP 43 protection for IQ8Quad detector bases, 

deep design 126 

IP 54 kit for large manual call points 7048xx 145 

IP55 kit for protective cover 147 

IP65 TG40 protective housing for 764708 and 

764723 260 

IP65 TG60 protective housing for 764708 and 

764723 261 

IQ8 MCP compact, red housing with plastic 

pane, French 149 

IQ8 MCP, red housing with glass pane - Esser 149 

IQ8 MCP, red housing with plastic pane - Esser 149 

IQ8Alarm combined alarm signalling device 234 

IQ8Alarm combined speech alarm 234 

IQ8Alarm combined speech alarm as 

customized version 234 

IQ8Alarm combined speech alarm with 

composition of other languages 234 

IQ8Alarm optical alarm signalling device / 

tranparent, blue, green 235 

IQ8Alarm optical alarm signalling device, 

amber 235 

IQ8Alarm optical alarm signalling device, red 235 

IQ8Alarm sounder, red 233 

IQ8Alarm sounder, white 233 

IQ8Alarm speech alarm, white 233 

IQ8Alarm speech alarm, red 233 

IQ8Control C/M operating front w. FBOIU - 

Esser, French/Switzerland 22 

IQ8Control C/M operating unit front w. 

FBOIU- Esser, Italian/Switzerland 22 

IQ8Control C/M operating unit front with FBOIU- 

Esser, German/Switzerland 22 

IQ8MCP electronic module 140 

IQ8MCP electronic module w/o isolator but with 

relay 140 

IQ8MCP electronic module with glass - Esser 150 

IQ8Quad O 2 T Intelligent Detector Ex (i) 115 

IQ8Quad O 2 T Intelligent detector without loop 

isolator 108 

IQ8Quad Optical Smoke Detector Ex (i) 115 

IQ8Quad Optical smoke detector without loop 

isolator 107 

IQ8Quad OTblue-LKM 185 

IQ8Quad Rate-of-rise Detector Ex (i) 115 

IQ8Quad Rate-of-rise detector without loop 

isolator 106 

IQ8TAL Technical Alarm Module 170 

IQ8TAM technical alarm module for snap-on 

mounting 169 

IQ8Wireless cover for wireless interface, red 

and white 178 

IQ8Wireless detector base 173 

IQ8Wireless gateway for devices 174 

IQ8Wireless mounting frame for IQ8Quad 

detectors, white 177 

IQ8Wireless mounting frames for IQ8Alarm, 

red and white 177 

IQ8Wireless transponder for devices, wall 

mount 175 

IQ8Wireless universal interface w/o cover, red 176 

IQ8Wireless universal interface w/o cover, white 177 

IR flame detector (ex) X 9800 181 

Isolation and assembly block for safety barrier 118 

Kit for limitation of capacity limit for FACP 8008 31 

Kit for suspended installation 135 

Label / marker ring for parallel detector 

indicator 246 

Label for release push button 256 

Label for release push button - Esser, German/ 

English 257 

Keyword Page 

Label plate for detector base IQ8Quad 125 

Labels-Sampling Points Wrap Round 226 

LAN-surge protection for snap-on mounting rail 260 

LaserFOCUS aspirating sytem - Esser, 

Multilingual 202 

LCD indicator panel - Esser, English 66 

LCD indicator panel - Esser, French 66 

LCD indicator panel - Esser, German 66 

LCD indicator panel - Esser, Italian 66 

LCD indicator panel - Esser, Polish 66 

LCD indicator panel - Esser, Spanish 66 

LCD indicator panel for system 800 - Esser, 

French 66 

Lever lock - type 17 for key no. 801 39 

Lever lock - type for key no. 901 39 

LF-manual activation point low frequency 154 

Line heat detector LWM-1 191 

Linear Smoke Detector LRMX 194 

Log book for FAS 267 

Loop isolator for transponders 167 

Loop LED remote indicator panel for 32 

messages - Esser 65 

LRS 100 aspirating smoke detector - Esser, 

English 203 


French 203 


Italian 203 


Spanish 203 

LRS 200 LCD-Programmer for aspirating system 209 

LRS 210 LCD-Programmer for aspirating system 209 

LRS 300 PC-Interface 209 

LRS compact - Esser, German 205 

LRS compact / net aspirating system - Esser, 

English 205 


French 206 


German 206 


Italian 206 


Spanish 206 

LRS compact aspirating system - Esser, English 205 

LRS compact aspirating system - Esser, French 205 

LRS compact aspirating system - Esser, Italian 205 

LRS compact aspirating system - Esser, Spanish 205 

LRS compact/EB - Esser, English 201 

LRS compact/EB - Esser, French 201 

LRS compact/EB - Esser, German 201 

LRS compact/EB - Esser, Italian 201 

LRS compact/EB - Esser, Spanish 201 

LRS-S 700 aspirating smoke detector - Esser, 

English 204 


French 204 


Italian 204 


Spanish 204 

Manual call point Series 9200, IP66 155 

Master box interface module 36 

Master system software for FACP 8008 29 

MCP Cover for small housing, transparent 152 

MCP housing with glass, printed: Hausalarm - 

ESSER 143 

MCP-electronic module Series 9000 with 

second micro-switch 142 

MCP-electronic module Series 9200 with zone 

isolator 142 

MCP-housing aluminium blue, neutral 143 

285 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

286 

Index 

Keyword Page 

MCP-housing aluminium grey, neutral 143 

MCP-housing aluminium red, neutral 143 

MCP-housing aluminium yellow, neutral 143 

MCP-housing with glass, blue, printed with 

“Hausalarm-ESSER” 143 

MCP-housing with glass, red, printed: 

Hausalarm - ESSER 143 

MD1L Transponder - Esser, French 166 



Metal key for large MCP 145 

Module housing for snap-on mounting rail 264 

Mounting adapter for intermediate ceilings 126 

Mounting bracket for lintel installation 256 

Mounting bracket for UniVario Flame Detector 180 

Mounting clip IKS for 25mm pipe 224 

Mounting frame 19” IQ8Control C/M and 

FACP 8000 C/M 24 

Mounting frame for small MCP, red and white 153 

Mounting kit 265 

Mounting kit for round and insulated air ducts 189 

Mounting plate for ceiling bracket for 

detector/single reflector 195 

Mounting rail for FACP 8000 C/M and 

IQ8Control C/M housing 264 

Mounting set for round and insulated air ducts 186 

Mounting spider for Ceiling Bracket 761404 

and 761405 195 

Multiprotocol Gateway DP7500 Esser - 

custom driver 82 

Multiprotocol Gateway DP7500 Esser - custom 

driver incl. HW 82 

Multiprotocol-Gateway DP1500 Esser - BACnet 

Client 80 


Server 80 

Multiprotocol-Gateway DP1500 Esser - 


Multiprotocol-Gateway DP1500 Esser - custom 

driver incl. HW 81 


EIB/Instabus 80 

Multiprotocol-Gateway DP1500 Esser - LONTalk 80 

Multiprotocol-Gateway DP1500 Esser - Modbus IP 80 


OPC Server 81 


BACnet Client 82 


BACnet Server 82 




custom driver incl. HW 82 




LONTalk 82 


Modbus IP 82 


OPC Server 82 


BACnet Client 79 


BACnet Server 79 




custom driver incl. HW 80 



Multiprotocol-Gateway DP500 Esser - LONTalk 79 


Keyword Page 

Multiprotocol-Gateway DP500 Esser - Modbus IP 79 

Multiprotocol-Gateway DP500 Esser - OPC Server 80 

Multiprotocol-Gateway DP7500 - OPC Server 82 


Client 81 


Server 81 




LONTalk 81 


Modbus IP 82 

Multi-stimulus detector tester 130 

Network interference suppression filter type 

2VK3 262 

O/So optical smoke detector IQ8Quad 112 

O 2 T multisensor IQ8Quad 108 

O 2 T multisensor IQ8Quad - France 108 

O 2 T/F multisensor IQ8Quad 112 

O 2 T/FSp multisensor detector IQ8Quad 113 

O 2 T/FSp multisensor detector IQ8Quad with 

composition of other languages 113 

O 2 T/FSp multisensor IQ8Quad 113 

O 2 T/So multisensor IQ8Quad 112 

O 2 T/Sp multisensor IQ8Quad 113 

Operating front - Esser, German 19 

Operating front 1/4 VGA and SZI for 64 zones - 

Esser, Chinese 20 

Operating front for printer w. take-up reel - 


Operating front w. 1/4 VGA display & SZI for 64 

zones - Esser, German 20 

Operating front w. 1/4 VGA display, printer - 


Operating front w. single zone indication 64 - 


Operating front with 1/4 VGA display - Esser, 

Chinese 20 

Operating front with 1/4 VGA display - Esser, 

German 20 

Operating front with printer, w/o take-up reel - 


Operating module front - Esser, German 29 

Operating module front with ¼ VGA display - 


Operating module front with 1/4 VGA display + 

printer - Esser, Chinese 21 

Optical alarm signalling device - amber 241 

Optical alarm signalling device - blue 242 

Optical alarm signalling device - green 242 

Optical alarm signalling device - red 241 

Optical alarm signalling device - transparent 242 

Optical smoke detector 103 

Optical smoke detector - Esser, China 103 

Optical smoke detector - Esser, France 103 

Optical smoke detector for ARS 70 220 

Optical smoke detector for ARS 70 - ELTEK 220 

Optical smoke detector IQ8Quad 106 

Optical smoke detector non-latched alarm - 

Esser 103 

Option – ability for customized interface 

rights (client-side) 93 

Option – Client 94 

Option – DTMF control option 93 

Option – escalation 93 

Option - notification 93 

Option – redundance 94 

Option – WEBX 93 

Option IP55 shrink sleeve for large 

MCP 80490x 144

Index 

Keyword Page 

OT multisensor detector IQ8Quad 107 

OT blue multisensor detector IQ8Quad 107 

OT blue multisensor IQ8Quad - France 107 

OTG multisensor (CO) IQ8Quad 108 

OTI-intelligent fire detector for 781453 188 

Out of order-sign - Multilingual for large MCP 144 

Package 1 of FACP 8008 34 

Package 2 of FACP 8008 with SZI 34 

Package 3 of FACP 8008 with printer 34 

Package 4 of FACP 8008 with SZI and printer 35 

Package IQ8Control C with two slots for 

micromodules 14 

Package IQ8Control M black box 18 

Package IQ8Control M with four slots for 


Package IQ8Control M with seven slots for 


Package of FACP 8008 - Esser, Chinese 35 

Package of FACP 8008 with SZI and printer 35 

Panel 8010-option with control group indicator 

and alarm counter 46 

Panel 8010-option with control group indicator 

and alarm counter, Dutch 46 

PanelSafe door switch for slave 53 

PanelSafe extra fan for slave 53 

PanelSafe slave connecting cable, 9-pin / 2m 53 

PanelSafe slave connecting cable, 9-pin / 5m 53 

PanelSafe, 19” cabinet extinguishing, basic 

module (master), German 52 

PanelSafe, 19” panel extinguishing system, slave 52 

Peripheral module 23 

Peripheral module with one additional 

micromodule slot 23 

Pipe (PVC), diameter 25mm 220 

Pipe cutter for PVC / ABS pipes 226 

Plastic key for large MCP 145 

Plastic pane - resettable function, for small 

MCP - Esser 151 

Plastic spare key for small MCP 152 

Plastic telescopic extension 129 

Plastic telescopic rod 129 

Power supply unit (12 V / 3A) for automatic 

door release systems 251 

Power supply unit (12 V / 3A) for automatic 

door release systems 251 

Power supply unit for FACP 8008 30 

Printer for mounting in wall housing - Esser 33 

Printer kit with paper take-up reel for 

IQ8Control C/M 24 

Printer paper for printer 736233 / 736234 24 

Printer paper for printer 736233 / 736234 32 

Printer paper for printer 736259 32 

Programming software for extinguishing 

control panel 8010, Series 2 and 3 47 

Protective cage 136 

Protective cover for manual call points - Esser, 

English 146 


French 146 


Italian 146 


Spanish 147 

Protective cover for manual call points Esser, 

German 146 

PVC adhesive, 0.5kg can 224 

PVC detergente, 1l can 224 

Rack 8 U extension for CMSI 8000 56 

Rate-of-rise heat detector 102 

Rate-of-rise heat detector - Esser, China 103 

Rate-of-rise heat detector - Esser, France 103 

Keyword Page 

Rate-of-rise heat detector IQ8Quad 106 

Rate-of-rise heat detector IQ8Quad - France 106 

Reflector set for 761400 for ranges up to 100 m 194 

Reflector set for 761400 for ranges up to 80 m 194 

Refurbishment zone transponder (RZT) / 12V - 

Esser 166 

Refurbishment zone transponder RZT 8000 165 

Refurbishment zone transponder RZT 8000 w. 

housing - Esser, French 166 

Relay box 263 

Remote indicator - Esser 245 

Remote indicator 781814/12V - Esser 245 

Remote indicator for detector series 9000, 

9200 and IQ8Quad 245 

Remote indicator for detector series 9200 and 

IQ8Quad 245 

Remote indicator, blue, for series 9200 and 

IQ8Quad 246 

Remote indicator, green, flashing 246 

Remote indicator, red 244 

Remote indicator, red, flush mount version, f. 

detector series 9000, 9200 + IQ8Quad 244 

Remote indicator, red, for detector series 9000 244 

Reset module for C-rail mounting 228 

Reset module for C-rail mounting - Esser, 

France 228 

Reset module with mounting bracket for 

Fireray 2000 228 

Reset PCB for Titanus EB 218 

RS 232/TTY serial interface module 36 

Sealing screws M4x6 262 

Sensor cable black 192 

Sensor cable black, with steel braiding 192 

Sensor cable blue (PVC) 192 

Separator for 25mm pipe 223 

Serial connecting cable for 789862 43 

Serial essernet interface EDP (bidirectional) 76 

Serial essernet interface EDP (unidirectional) 76 

Serial interface for WINMAGplus / WINMAGLite 84 

Service key for electronic module 

(Part No. 80490x) 145 

Shallow base sounder, red 237 

Signal base 238 

Single reflector for LRMX 761400 195 

Single zone indication module with bus board 33 

Single zone indicator card for max. of 64 zones 31 

Slave system software for FACP 8008 29 

Sleeve (PVC) for 25mm pipe 221 

Small funnel (polypropylen) for 25mm pipe 223 

Smoke capsule for Multi-stimulus detector tester 

805551 131 

Smoke detector tester 131 

Smoke detector tester 133 

Smoke pellets for testing purposes 135 

Software package ECS 8000M - Esser, French 58 

Sound absorber for Titanus EB aspirating 

smoke detection systems 218 

Sounder with low-profile base, white 237 

Sounder, red 237 

Spare battery baton 133 

Spare filter 188 

Spare filter for filter chamber 761532 224 

Spare filter for VESDA aspirating smoke 

systems 210 

Spare glass pane for MCP-housings 70490x, 

7048xx und 761694 144 

Spare glass pane for small MCP, EN54 - Esser 151 

Spare glass pane for small MCP, EN54 - neutral 151 

Spare glass pane red for MCP-housings 

7047xx und 7048xx 144 

Spare key 1D9 for FACP 39 

Spare key 801 for FACP 39 

287 

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

12 

13 

14

288 

Index 

Keyword Page 

Spare key 901 for FACP 39 

Standard detector base for IQ8Quad 121 

Standard detector base series 9000 - Esser, 

France 120 

Standard detector base series 9000 - Esser, 

France 120 

Standard detector base series 9x00 120 

Standard interface module for System 8000 

and IQ8Control C/M 37 

Standard LED remote indicator panel - Esser 65 

Suctions hose set for 25mm pipe 225 

Surface mount adapter for series 9x00 122 

Surface mount adapter for series 9x00 - Esser, 

France 122 

Surface mount base adapter for series 9x00 123 

Surface mount base adapter for series 9x00 - 

Esser, France 123 

Surface mount housing for small MCP, blue 153 

Surface mount housing for small MCP, red 153 

Surface mount release key for automatic door - 

arrester system, German 252 

Surface spacer for protective cover 147 

Surge protection for network and low-frequency 

signal loop 260 

Switched-mode power supply with cylindrical 

plug 43 

SZI front for 192 detector zones 21 

TAL optocoupler input / isolator 168 

TAL optocoupler input / isolator - Esser, German 168 

TAL optocoupler input / relay IP 54 169 

TAL optocoupler input /relay - Esser, German 168 

Telescopic rod 134 

Terminal card for LF-manual call point 761630 154 

Terminal card for panel 8010 Series 2 and 3 in 

19-inch technology (3 UH), 2m 51 

Terminal card power supply, series 3 30 

Termination link set for sensor cable 191 

Test gas for smoke detecetor tester 805582 132 

Test gas for smoke detector testers 769870.10 

and 769870 134 

Test head for heat detector together with 

battery and charger 133 

Text page input 95 

Threaded cable connection for housing 764752 119 

Threaded joint, detachable, 25mm 225 

tools 8000 PLus equipment starter kit 41 

tools 8000 programming software 41 

Top-hat rail 264 

T-Piece (PVC) for 25mm pipe 221 

UniVario MX5000.ESSER standard base 180 

Universal gateway for PC (software) 91 

Upright cabinet 38 

Upright cabinet including mounting 38 

USB cable A/B for 789862 field bus & panel 

interface 42 

UV flame detector (ex) X 2200 182 

UV Flame Detector UniVario Type FMX5000UV. 

ESSER 180 

UV/IR flame detector (ex) X 5200 183 

Vent (PVC) for 25mm pipe 222 

Venturi air duct module for IQ8Quad 

OTb lue -LKM (802379) 184 

Venturi principle air duct kit 187 

Venturi tube 0.6m for IQ8Quad air duct 

construction set 781443 185 





Venturi tube, 0.6m 188 


Keyword Page 



VESDAnet connection box 209 

VSM3 software - basic system 210 

Weather protection housing for air duct 


Weather protective cover for air duct kit 

781453 190 

Weather protective cover, blue for MCPhousings 

7047/48xx 146 

Weather protective cover, red for MCPhousings 

7047/48xx 146 

WINMAG upgrade as of version 6 to 

WINMAGplus 88 

WINMAG upgrade to WINMAGplus 88 

WINMAGLIte upgrade to WINMAGplus 

full version 98 

WINMAGLite with USB dongle 98 

WINMAGplus – 4-monitor support option 94 

WINMAGplus – AutoCAD option 95 

WINMAGplus – OEM option 95 

WINMAGplus - remote-access package 94 

WINMAGplus – translation tool 94 

WINMAGplus control centre software - 

subsequent 

upgrade 88 

WINMAGplus Licence – CMSI 90 

WINMAGplus licence - fire detection technology 89 

WINMAGplus Licence - intrusion detection 

technology 89 

WINMAGplus Licence – OPC client 92 

WINMAGplus Licence – OPC server 92 

WINMAGplus Licence - rescue route 

technology/escape door control 90 

WINMAGplus Licence - RTD 90 

WINMAGplus Licence - video technology 89 

WINMAGplus Licence connection server 91 

WINMAGplus Licence nurse call systems 90 

WINMAGplus Licence VA/PA 91 

WINMAGplus License - access control 89 

WINMAGplus License - interfacing DEZ 9000 90

Novar GmbH a Honeywell Company 

Dieselstr. 2, 41469 Neuss, Germany 

Phone: +49 2137 17-0 (Administration) 

Phone: +49 2137 17-600 (Customer Service Center) Part No. 054581.G0 

Fax: +49 2137 17-286 September 2008 

Internet: www.esser-systems.com Subject to change without notice 

E-mail: info@esser-systems.com ©2008 Honeywell International Inc.

Fire Alarm Systems

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?